• BS EN 12101-3:2015

    Current The latest, up-to-date edition.

    SMOKE AND HEAT CONTROL SYSTEMS - SPECIFICATION FOR POWERED SMOKE AND HEAT EXHAUST VENTILATORS (FANS)

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2015

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    European foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions, symbols and abbreviations
    4 Requirements
    5 Testing, assessment and sampling methods
    6 Assessment and verification of constancy of
      performance - AVCP
    7 Marking, labelling and packaging
    Annex A (normative) - Criteria to determine family of fans
            in order to select the sizes to be tested
    Annex B (normative) - Criteria to determine a family of
            motors in order to select the sizes to be tested
    Annex C (normative) - Test method for the determination
            of fire resistance of powered smoke and heat control
            ventilators (fans)
    Annex D (normative) - Test methods for electric motors to
            determine the impact of the changes on the product
            characteristics
    Annex E (normative) - Test method for assessing the
            response delay and ability to open under environmental
            conditions
    Annex F (informative) - Explanatory notes
    Annex G (informative) - General guidance for installation
            and maintenance
    Annex ZA (informative) - Clauses of this European Standard
             addressing the provisions of the EU Construction
             Products Regulation
    Bibliography

    Abstract - (Show below) - (Hide below)

    Defines the products characteristics of powered smoke and heat control ventilators (fans) intended to be used as part of a powered smoke and heat control ventilation system in construction works.

    General Product Information - (Show below) - (Hide below)

    Committee FSH/25
    Development Note Supersedes 95/542302 DC (06/2002) Supersedes BS 7346-2(1990). (05/2013)
    Document Type Standard
    Publisher British Standards Institution
    Status Current
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS 9991:2011 FIRE SAFETY IN THE DESIGN, MANAGEMENT AND USE OF RESIDENTIAL BUILDINGS - CODE OF PRACTICE
    09/30189450 DC : 0 BS 8519 - CODE OF PRACTICE FOR THE SELECTION AND INSTALLATION OF FIRE-RESISTANT CABLES AND SYSTEMS FOR LIFE SAFETY AND FIRE-FIGHTING APPLICATIONS
    NFPA 204 : 2018 SMOKE AND HEAT VENTING
    BS 7346-7:2006 COMPONENTS FOR SMOKE AND HEAT CONTROL SYSTEMS - PART 7: CODE OF PRACTICE ON FUNCTIONAL RECOMMENDATIONS AND CALCULATION METHODS FOR SMOKE AND HEAT CONTROL SYSTEMS FOR COVERED CAR PARKS
    BS 5588-5:2004 FIRE PRECAUTIONS IN THE DESIGN, CONSTRUCTION AND USE OF BUILDINGS - PART 5: ACCESS AND FACILITIES FOR FIRE-FIGHTING
    11/30203947 DC : 0 BS 9991 - FIRE SAFETY IN THE DESIGN, MANAGEMENT AND USE OF RESIDENTIAL BUILDINGS - CODE OF PRACTICE
    BS 8519:2010 SELECTION AND INSTALLATION OF FIRE-RESISTANT POWER AND CONTROL CABLE SYSTEMS FOR LIFE SAFETY AND FIRE-FIGHTING APPLICATIONS - CODE OF PRACTICE
    06/30112774 DC : DRAFT APR 2006 BS 7346-7 - COMPONENTS FOR SMOKE AND HEAT CONTROL SYSTEMS - PART 7: CODE OF PRACTICE ON FUNCTIONAL RECOMMENDATIONS AND CALCULATION METHODS FOR SMOKE AND HEAT CONTROL SYSTEMS FOR COVERED CAR PARKS
    13/30264663 DC : 0 BS 7346-7 - COMPONENTS FOR SMOKE AND HEAT CONTROL SYSTEMS - PART 7: CODE OF PRACTICE ON FUNCTIONAL RECOMMENDATIONS AND CALCULATION METHODS FOR SMOKE AND HEAT CONTROL SYSTEMS FOR COVERED CAR PARKS
    BS 7346-7:2013 COMPONENTS FOR SMOKE AND HEAT CONTROL SYSTEMS - PART 7: CODE OF PRACTICE ON FUNCTIONAL RECOMMENDATIONS AND CALCULATION METHODS FOR SMOKE AND HEAT CONTROL SYSTEMS FOR COVERED CAR PARKS

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM E 228 : 2017 : REDLINE Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer
    EN ISO 6892-1:2016 METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT ROOM TEMPERATURE (ISO 6892-1:2016)
    EN 12101-2:2017 Smoke and heat control systems - Part 2: Natural smoke and heat exhaust ventilators
    EN 60085:2008 ELECTRICAL INSULATION - THERMAL EVALUATION AND DESIGNATION
    EN 60034-1:2010/corrigendum Oct. 2010 ROTATING ELECTRICAL MACHINES - PART 1: RATING AND PERFORMANCE
    ISO 6892-1:2016 Metallic materials Tensile testing Part 1: Method of test at room temperature
    EN 13501-4:2016 Fire classification of construction products and building elements - Part 4: Classification using data from fire resistance tests on components of smoke control systems
    ISO 3:1973 Preferred numbers Series of preferred numbers
    EN ISO 204 : 2009 METALLIC MATERIALS - UNIAXIAL CREEP TESTING IN TENSION - METHOD OF TEST
    ISO 281:2007 Rolling bearings Dynamic load ratings and rating life
    EN 60034-18-41:2014 ROTATING ELECTRICAL MACHINES - PART 18-41: PARTIAL DISCHARGE FREE ELECTRICAL INSULATION SYSTEMS (TYPE 1) USED IN ROTATING ELECTRICAL MACHINES FED FROM VOLTAGE CONVERTERS - QUALIFICATION AND QUALITY CONTROL TESTS (IEC 60034-18-41:2014)
    ASTM E 1461 : 2013 : REDLINE Standard Test Method for Thermal Diffusivity by the Flash Method
    EN ISO 5801:2017 FANS - PERFORMANCE TESTING USING STANDARDIZED AIRWAYS (ISO 5801: 2017)
    ISO 5801:2017 Fans — Performance testing using standardized airways
    IEC 60085:2007 Electrical insulation - Thermal evaluation and designation
    IEC 60034-2-1:2014 Rotating electrical machines - Part 2-1: Standard methods for determining losses and efficiency from tests (excluding machines for traction vehicles)
    EN ISO 9001:2015 QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS (ISO 9001:2015)
    IEC TS 60034-17:2006 Rotating electrical machines - Part 17: Cage induction motors when fed from converters - Application guide
    IEC 60034-18-41:2014 Rotating electrical machines - Part 18-41: Partial discharge free electrical insulation systems (Type I) used in rotating electrical machines fed from voltage converters - Qualification and quality control tests
    EN 60034-2-1 : 2014 ROTATING ELECTRICAL MACHINES - PART 2-1: STANDARD METHODS FOR DETERMINING LOSSES AND EFFICIENCY FROM TESTS (EXCLUDING MACHINES FOR TRACTION VEHICLES) (IEC 60034-2-1:2014)
    IEC 60034-1:2017 Rotating electrical machines - Part 1: Rating and performance
    EN ISO 6892-2 : 2011 METALLIC MATERIALS - TENSILE TESTING - PART 2: METHOD OF TEST AT ELEVATED TEMPERATURE
    ISO 9001:2015 Quality management systems - Requirements
    ISO 14520-1:2015 Gaseous fire-extinguishing systems Physical properties and system design Part 1: General requirements
    ISO 6892-2:2011 Metallic materials Tensile testing Part 2: Method of test at elevated temperature
    ISO 1099:2017 Metallic materials — Fatigue testing — Axial force-controlled method
    CLC/TS 60034-17 : 2004 ROTATING ELECTRICAL MACHINES - PART 17: CAGE INDUCTION MOTORS WHEN FED FROM CONVERTERS - APPLICATION GUIDE
    ISO 834-1:1999 Fire-resistance tests Elements of building construction Part 1: General requirements
    ISO 204:2009 Metallic materials Uniaxial creep testing in tension Method of test
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective