• I.S. EN 12101-3:2015

    Current The latest, up-to-date edition.

    SMOKE AND HEAT CONTROL SYSTEMS - PART 3: SPECIFICATION FOR POWERED SMOKE AND HEAT CONTROL VENTILATORS (FANS)

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2015

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National Foreword
    European foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions, symbols and abbreviations
    4 Requirements
    5 Testing, assessment and sampling methods
    6 Assessment and verification of constancy of
      performance - AVCP
    7 Marking, labelling and packaging
    Annex A (normative) - Criteria to determine family of fans
            in order to select the sizes to be tested
    Annex B (normative) - Criteria to determine a family of
            motors in order to select the sizes to be tested
    Annex C (normative) - Test method for the determination
            of fire resistance of powered smoke and heat control
            ventilators (fans)
    Annex D (normative) - Test methods for electric motors to
            determine the impact of the changes on the product
            characteristics
    Annex E (normative) - Test method for assessing the
            response delay and ability to open under environmental
            conditions
    Annex F (informative) - Explanatory notes
    Annex G (informative) - General guidance for installation
            and maintenance
    Annex ZA (informative) - Clauses of this European Standard
             addressing the provisions of the EU Construction
             Products Regulation
    Bibliography

    Abstract - (Show below) - (Hide below)

    Defines the products characteristics of powered smoke and heat control ventilators (fans) intended to be used as part of a powered smoke and heat control ventilation system in construction works.

    General Product Information - (Show below) - (Hide below)

    Development Note 2002 COR 2005 Issued on 15/08/2010. (09/2010)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM E 228 : 2017 : REDLINE Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer
    EN ISO 6892-1:2016 METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT ROOM TEMPERATURE (ISO 6892-1:2016)
    EN 12101-2:2017 Smoke and heat control systems - Part 2: Natural smoke and heat exhaust ventilators
    EN 60085:2008 ELECTRICAL INSULATION - THERMAL EVALUATION AND DESIGNATION
    EN 60034-1:2010/corrigendum Oct. 2010 ROTATING ELECTRICAL MACHINES - PART 1: RATING AND PERFORMANCE
    ISO 6892-1:2016 Metallic materials Tensile testing Part 1: Method of test at room temperature
    EN 13501-4:2016 Fire classification of construction products and building elements - Part 4: Classification using data from fire resistance tests on components of smoke control systems
    ISO 3:1973 Preferred numbers Series of preferred numbers
    EN ISO 204 : 2009 METALLIC MATERIALS - UNIAXIAL CREEP TESTING IN TENSION - METHOD OF TEST
    ISO 281:2007 Rolling bearings Dynamic load ratings and rating life
    EN 60034-18-41:2014 ROTATING ELECTRICAL MACHINES - PART 18-41: PARTIAL DISCHARGE FREE ELECTRICAL INSULATION SYSTEMS (TYPE 1) USED IN ROTATING ELECTRICAL MACHINES FED FROM VOLTAGE CONVERTERS - QUALIFICATION AND QUALITY CONTROL TESTS (IEC 60034-18-41:2014)
    ASTM E 1461 : 2013 : REDLINE Standard Test Method for Thermal Diffusivity by the Flash Method
    EN ISO 5801:2017 FANS - PERFORMANCE TESTING USING STANDARDIZED AIRWAYS (ISO 5801: 2017)
    ISO 5801:2017 Fans — Performance testing using standardized airways
    IEC 60085:2007 Electrical insulation - Thermal evaluation and designation
    IEC 60034-2-1:2014 Rotating electrical machines - Part 2-1: Standard methods for determining losses and efficiency from tests (excluding machines for traction vehicles)
    EN ISO 9001:2015 QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS (ISO 9001:2015)
    IEC TS 60034-17:2006 Rotating electrical machines - Part 17: Cage induction motors when fed from converters - Application guide
    IEC 60034-18-41:2014 Rotating electrical machines - Part 18-41: Partial discharge free electrical insulation systems (Type I) used in rotating electrical machines fed from voltage converters - Qualification and quality control tests
    EN 60034-2-1 : 2014 ROTATING ELECTRICAL MACHINES - PART 2-1: STANDARD METHODS FOR DETERMINING LOSSES AND EFFICIENCY FROM TESTS (EXCLUDING MACHINES FOR TRACTION VEHICLES) (IEC 60034-2-1:2014)
    IEC 60034-1:2017 Rotating electrical machines - Part 1: Rating and performance
    EN ISO 6892-2 : 2011 METALLIC MATERIALS - TENSILE TESTING - PART 2: METHOD OF TEST AT ELEVATED TEMPERATURE
    ISO 9001:2015 Quality management systems - Requirements
    ISO 14520-1:2015 Gaseous fire-extinguishing systems Physical properties and system design Part 1: General requirements
    ISO 6892-2:2011 Metallic materials Tensile testing Part 2: Method of test at elevated temperature
    ISO 1099:2017 Metallic materials — Fatigue testing — Axial force-controlled method
    CLC/TS 60034-17 : 2004 ROTATING ELECTRICAL MACHINES - PART 17: CAGE INDUCTION MOTORS WHEN FED FROM CONVERTERS - APPLICATION GUIDE
    ISO 834-1:1999 Fire-resistance tests Elements of building construction Part 1: General requirements
    ISO 204:2009 Metallic materials Uniaxial creep testing in tension Method of test
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective