IEC 60243-1:2013
|
Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
IEC 60112:2003+AMD1:2009 CSV
|
Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
EN ISO 75-3:2004/AC:2006
|
Plastics - Determination of temperature of deflection under load - Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics (ISO 75-3:2004) |
EN ISO 180:2000/A2:2013
|
PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH (ISO 180:2000/AMD 2:2013) |
IEC 60695-2-1:1991
|
Fire hazard testing - Part 2: Test methods - Section 1: Glow-wire test and guidance |
IEC 60250:1969
|
Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
EN ISO 527-2:2012
|
Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012) |
ISO 295:2004
|
Plastics — Compression moulding of test specimens of thermosetting materials |
ISO 1172:1996
|
Textile-glass-reinforced plastics — Prepregs, moulding compounds and laminates — Determination of the textile-glass and mineral-filler content — Calcination methods |
EN ISO 75-1:2013
|
Plastics - Determination of temperature of deflection under load - Part 1: General test method (ISO 75-1:2013) |
EN ISO 178:2010/A1:2013
|
PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013) |
ISO 10350:1993
|
Plastics Acquisition and presentation of comparable single-point data |
EN ISO 527-1:2012
|
Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012) |
EN ISO 75-2:2013
|
Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013) |
EN ISO 6603-1 : 2000
|
PLASTICS - DETERMINATION OF PUNCTURE IMPACT BEHAVIOUR OF RIGID PLASTICS - PART 1: NON-INSTRUMENTED IMPACT TESTING |
ISO 1183:1987
|
Plastics Methods for determining the density and relative density of non-cellular plastics |
IEC 60093:1980
|
Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials |
ISO 472:2013
|
Plastics Vocabulary |
ISO 1210:1992
|
Plastics — Determination of the burning behaviour of horizontal and vertical specimens in contact with a small-flame ignition source |
EN ISO 179 : 1996
|
PLASTICS - DETERMINATION OF CHARPY IMPACT STRENGTH |
EN ISO 12115 : 1997
|
FIBRE-REINFORCED PLASTICS - THERMOSETTING MOULDING COMPOUNDS AND PREPREGS - DETERMINATION OF FLOWABILITY, MATURATION AND SHELF LIFE |
EN ISO 6603-2:2000
|
Plastics - Determination of puncture impact behaviour of rigid plastics - Part 2: Instrumented puncture test (ISO 6603-2:2000) |
ISO 62:2008
|
Plastics Determination of water absorption |
ISO 4589:1984
|
Plastics Determination of flammability by oxygen index |
IEC 60243-2:2013
|
Electric strength of insulating materials - Test methods - Part 2: Additional requirements for tests using direct voltage |
EN ISO 12114 : 1997
|
FIBRE-REINFORCED PLASTICS - THERMOSETTING MOULDING COMPOUNDS AND PREPREGS - DETERMINATION OF CURE CHARACTERISTICS (ISO 12114:1997) |
ISO 8604:1988
|
Plastics — Prepregs — Definitions of terms and symbols for designations |
ISO 12114:1997
|
Fibre-reinforced plastics — Thermosetting moulding compounds and prepregs — Determination of cure characteristics |
EN 1842:1997
|
Plastics - Thermoset moulding compounds (SMC - BMC) - Determination of compression moulding shrinkage |