BS EN 12735-2:2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Copper and copper alloys. Seamless, round tubes for air conditioning and refrigeration Tubes for equipment
Hardcopy , PDF
08-11-2024
English
30-06-2016
Important note : Users cannot be edited or removed once added to your Multi user PDF.
European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Designations
5 Ordering information
6 Requirements
7 Sampling
8 Test methods
9 Declaration of conformity and inspection documentation
10 Packaging, marking and form of delivery
Annex A (normative) - Freedom from defects test
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of
Directive 2014/68/EU aimed to be covered
Bibliography
Defines the requirements, sampling, test methods and conditions of delivery for seamless round copper tubes, smooth or inner finned, used for heat exchangers and their internal connecting pipes in the manufacturing of refrigeration and air conditioning equipment
| Committee |
NFE/34
|
| DevelopmentNote |
Supersedes 97/702696 DC. (09/2004)
|
| DocumentType |
Standard
|
| Pages |
30
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This European Standard specifies the requirements, sampling, test methods and conditions of delivery for seamless round copper tubes, smooth or inner finned, used for heat exchangers and their internal connecting pipes in the manufacturing of refrigeration and air conditioning equipment. It is applicable to tubes with an outside diameter from 3,97mm up to and including 219mm. NOTE The tubes are supplied in straight length in the material conditions hard, half-hard or skin hard or as coils in the material conditions light annealed or soft annealed.
| Standards | Relationship |
| NBN EN 12735-2 : 2016 | Identical |
| I.S. EN 12735-2:2016 | Identical |
| DIN EN 12735-2:2015-11 (Draft) | Identical |
| SN EN 12735-2 : 2016 | Identical |
| UNI EN 12735-2 : 2010 | Identical |
| NF EN 12735-2 : 2016 | Identical |
| NEN EN 12735-2 : 2016 | Identical |
| UNE-EN 12735-2:2016 | Identical |
| NS EN 12735-2 : 2016 | Identical |
| EN 12735-2:2016 | Identical |
| DIN EN 12735-2:2001-07 | Identical |
| ISO 6507-1:2005 | Metallic materials Vickers hardness test Part 1: Test method |
| EN 1655:1997 | Copper and copper alloys - Declarations of conformity |
| EN 1971-2:2011 | Copper and copper alloys - Eddy current test for measuring defects on seamless round copper and copper alloy tubes - Part 2: Test with an internal probe on the inner surface |
| EN ISO 8493:2004 | Metallic materials - Tube - Drift-expanding test (ISO 8493:1998) |
| EN 1412:2016 | Copper and copper alloys - European numbering system |
| ISO 1190-1:1982 | Copper and copper alloys — Code of designation — Part 1: Designation of materials |
| EN ISO 6892-1:2016 | Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016) |
| ISO 2624:1990 | Copper and copper alloys — Estimation of average grain size |
| EN 1057:2006+A1:2010 | Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications |
| ISO 1553:1976 | Unalloyed copper containing not less than 99,90 % of copper Determination of copper content Electrolytic method |
| ISO 6892-1:2016 | Metallic materials Tensile testing Part 1: Method of test at room temperature |
| ISO 8493:1998 | Metallic materials Tube Drift-expanding test |
| EN 723:2009 | Copper and copper alloys - Combustion method for determination of the carbon content on the inner surface of copper tubes or fittings |
| ISO 6708:1995 | Pipework components Definition and selection of DN (nominal size) |
| EN 1971-1:2011 | Copper and copper alloys - Eddy current test for measuring defects on seamless round copper and copper alloy tubes - Part 1: Test with an encircling test coil on the outer surface |
| EN 1173:2008 | Copper and copper alloys - Material condition designation |
| EN ISO 6708:1995 | Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995) |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN ISO 2624:1995 | Copper and copper alloys - Estimation of average grain size (ISO 2624:1990) |
| ISO 4741:1984 | Copper and copper alloys — Determination of phosphorus content — Molybdovanadate spectrometric method |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| 2014/68/EU : 2014 COR 1 2015 | DIRECTIVE 2014/68/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 15 MAY 2014 ON THE HARMONISATION OF THE LAWS OF THE MEMBER STATES RELATING TO THE MAKING AVAILABLE ON THE MARKET OF PRESSURE EQUIPMENT TEXT WITH EEA RELEVANCE |
| ISO 9001:2015 | Quality management systems — Requirements |
| ISO 857-2:2005 | Welding and allied processes Vocabulary Part 2: Soldering and brazing processes and related terms |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.