BS EN 1279-6:2002
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Glass in building. Insulating glass units Factory production control and periodic tests
Hardcopy , PDF
06-08-2018
English
12-07-2002
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Quality assurance and factory production control
5 Factory production control requirements
6 Handling, storage, packaging and delivery
7 Training of personnel
Annex A (normative) Inspection and testing tables of
insulating glass units
Annex B (normative) Periodic testing and inspections
Annex C (normative) Fogging test
Annex D (informative) Two component sealants, check
on the thoroughness of mixing
Annex E (informative) Sealants, hardness measurements
Annex F (informative) Seals, adherence measurements
Annex G (informative) Volatile test
Annex H (informative) Tightness check of hollow spacer
closed by welding on the back
Annex J (informative) Adhesion test for leaded light strip
Annex K (informative) Desiccant, adsorption capacity check
Bibliography
Specifies insulating glass units, and ensures by means of an adequate evaluation of conformity to this standard that over time.
Committee |
B/520
|
DevelopmentNote |
Supersedes 97/100572 DC. (08/2002) Also available as part of BS KIT 168. (09/2005)
|
DocumentType |
Standard
|
Pages |
72
|
PublisherName |
British Standards Institution
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
This draft European Standard is the product standard for insulating glass units, which defines insulating glass units, and ensures by means of an adequate evaluation of conformity to this standard that: - energy savings are made because the U-value and solar factor do not change significantly; - health because sound reduction and vision do not change significantly; - safety is provided because mechanical resistance does not change significantly.
Standards | Relationship |
NBN EN 1279-6 : 2002 | Identical |
UNI EN 1279-6 : 2004 | Identical |
DIN EN 1279-6:2015-08 (Draft) | Identical |
UNE-EN 1279-6:2002 | Identical |
ONORM EN 1279-6 : 2002 | Identical |
NS EN 1279-6 : 1ED 2002 | Identical |
I.S. EN 1279-6:2002 | Identical |
SN EN 1279-6 : 2002 | Identical |
EN 1279-6:2002 | Identical |
NEN EN 1279-6 : 2002 | Identical |
NF EN 1279-6 : 2002 | Identical |
BS 6262-1:2017 | Glazing for buildings General methodology for the selection of glazing |
EN 10218-1:2012 | Steel wire and wire products - General - Part 1: Test methods |
ISO/IEC Guide 62:1996 | General requirements for bodies operating assessment and certification/registration of quality systems |
PREN 1279-1 : DRAFT 95 | GLASS IN BUILDING - INSULATING GLASS UNITS - PART 1: GENERALITIES AND DIMENSIONAL TOLERANCES |
PREN 1279-3 : DRAFT 2015 | GLASS IN BUILDING - INSULATING GLASS UNITS - PART 3: LONG TERM TEST METHOD AND REQUIREMENTS FOR GAS LEAKAGE RATE AND FOR GAS CONCENTRATION TOLERANCES |
ISO 2859:1974 | Sampling procedures and tables for inspection by attributes |
PREN 1279-2 : DRAFT 2015 | GLASS IN BUILDING - INSULATING GLASS UNITS - PART 2: LONG TERM TEST METHOD AND REQUIREMENTS FOR MOISTURE PENETRATION |
EN 45011:1998 | General requirements for bodies operating product certification systems (ISO/IEC Guide 65:1996) |
ISO 2137:2007 | Petroleum products and lubricants Determination of cone penetration of lubricating greases and petrolatum |
EN 45011 : 1998 | GENERAL REQUIREMENTS FOR BODIES OPERATING PRODUCT CERTIFICATION SYSTEMS |
EN 1279-4:2002 | Glass in building - Insulating glass units - Part 4: Methods of test for the physical attributes of edge seals |
EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
ISO 7619:1997 | Rubber Determination of indentation hardness by means of pocket hardness meters |
EN 10204:2004 | Metallic products - Types of inspection documents |
ISO 9001:2015 | Quality management systems — Requirements |
MIL-I-25135 Revision E:1984 | INSPECTION MATERIALS, PENETRANTS |
ISO/IEC Guide 65:1996 | General requirements for bodies operating product certification systems |
EN 45012 : 1998 | GENERAL REQUIREMENTS FOR BODIES OPERATING ASSESSMENT AND CERTIFICATION/REGISTRATION OF QUALITY SYSTEMS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.