BS EN 129000:1996
Current
The latest, up-to-date edition.
Harmonized system of quality assessment for electronic components. Generic specification. Fixed RF wound inductors
Hardcopy , PDF
English
15-10-1996
Foreword
1 Scope
2 General
2.1 Related documents
2.2 Units, symbols and terminology
2.3 Preferred values
2.4 Marking
3 Quality assessment procedures
3.1 Qualification approval/Quality assessment systems
3.2 Primary stage of manufacture
3.3 Structurally similar components
3.4 Qualification approval procedures
3.5 Quality conformance inspection
3.6 Alternative test methods
3.7 Unchecked parameters
3.8 Manufacturing stages in a factory other than the
approved manufacturer's and/or outside the
geographical limits of CECC
4 Tests and measuring methods
4.1 General
4.2 Standard atmospheric conditions
4.3 Drying
4.4 Visual examination and check of dimensions
4.5 Insulation resistance
4.6 Voltage proof
4.7 Inductance
4.8 Q-factor
4.9 Self-resonant frequency
4.10 D.C. resistance
4.11 Robustness of terminations
4.12 Resistance to soldering heat
4.13 Solderability
4.14 Rapid change of temperature
4.15 Vibration
4.16 Bump
4.17 Shock
4.18 Sealing
4.19 Climatic sequence
4.20 Damp, heat, steady state
4.21 Temperature rise
4.22 Endurance
4.23 Change of inductance with current (superimposed
direct current)
4.24 Component solvent resistance
4.25 Solvent resistance of marking
4.26 Passive flammability
4.27 Active flammability
Annex
A Interpretation of sampling plans and procedures as
described in IEC 410 for use within the CECC System
electronic components
Figure
1 Suitable insulation resistance and voltage proof
test apparatus for surface mounting inductors
Applicable to RF fixed wound inductors (with inductance values below 10 mH) for use in electronic equipment. It establishes standard terms, inspection procedures and methods of test for use in sectional specifications within the CECC system for electronic components.
Committee |
EPL/51
|
DevelopmentNote |
Supersedes BS 9750(1990). (08/2005)
|
DocumentType |
Standard
|
Pages |
22
|
PublisherName |
British Standards Institution
|
Status |
Current
|
Supersedes |
Standards | Relationship |
EN 129000:1993/A1:1995 | Identical |
I.S. EN 129000:1993 | Identical |
DIN EN 129000:1994-03 | Identical |
NEN EN 129000 : 1995 AMD 1 1995 | Identical |
SN EN 129000 : AMD 1 1995 | Identical |
BS EN 129100:1995 | Harmonized system of quality assessment for electronic components. Sectional specification: wirewound surface mounting inductors |
BS EN 129200:1996 | Harmonized system of quality assessment for electronic components. Sectional specification: fixed inductors with ceramic or ferrite core wound with copper wire for RF circuits |
BS 5555:1993 | Specification for SI units and recommendations for the use of their multiples and of certain other units |
BS EN 60068-1:2014 | Environmental testing General and guidance |
BS 5692:1979 | Method for measurement of the dimensions of a cylindrical electronic component having two axial terminations |
BS 6062-1:1981 | Packaging of electronic components for automatic handling Specification for tape packaging of components with axial leads on continuous tapes |
BS EN 60695-2-2:1995 | Fire hazard testing. Test methods Needle-flame test |
BS 2011-2.1M:1984 | Environmental testing. Tests Test M. Low air pressure |
BS EN 60068-2-27:2009 | Environmental testing Tests. Test Ea and guidance. Shock |
BS EN 60068-2-29:1993 | Environmental testing. Test methods Environmental testing procedures. Tests. Test Eb and guidance. Bump |
CECC 00100 : 1988 | BASIC RULES - TO BE USED IN CONNECTION WITH THE INTERNAL REGULATIONS OF THE FEN e.V |
ISO 3:1973 | Preferred numbers Series of preferred numbers |
IEC 60027-1:1992 | Letters symbols to be used in electrical technology - Part 1: General |
BS 2011-2.1N:1985 | Environmental testing. Tests Test N. Change of temperature |
BS 6062-2:1988 | Packaging of electronic components for automatic handling Specification for tape packaging of components with unidirectional leads on continuous tapes |
BS 2011-2.1Ca:1977 | Environmental testing. Tests Test Ca. Damp heat, steady state |
BS EN 60068-2-45:1993 | Environmental testing. Test methods Environmental testing. Tests. Test XA and guidance. Immersion in cleaning solvents |
IEC 60410:1973 | Sampling plans and procedures for inspection by attributes |
BS EN 60068-2-1:2007 | Environmental testing Tests. Test A. Cold |
BS CECC 00114-2:1995 | Rule of procedure 14. Quality assessment procedures Qualification approval of electronic components |
IEC 60062:2016 | Marking codes for resistors and capacitors |
BS EN 60068-2-17:1995 | Environmental testing. Test methods Test Q. Sealing |
BS EN 60068-2-2:2007 | Environmental testing Tests. Test B. Dry heat |
IEC 60063:2015 | Preferred number series for resistors and capacitors |
ISO 497:1973 | Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers |
BS 2011-2.1T:1981 | Environmental testing. Tests Test T. Soldering |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.