BS EN 15649-7:2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Floating leisure articles for use on and in the water Additional specific safety requirements and test methods for Class E devices
Hardcopy , PDF
31-10-2017
English
31-12-2009
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Materials
5 Construction and functional components of boats
6 Safety requirements and test methods
7 Performance requirements and test methods for boats
8 Standard equipment and accessories for boats
9 Marking
10 Instructions for use for boats
11 Exclusions
Annex A (normative) - Inflatable canoes, kayaks and
sit-on-top kayaks
Annex B (normative) - Inflatable boat propelled by
sail or motor
Annex C (informative) - General arrangement of a typical
boat with the hull made of
non-reinforced material
Annex D (informative) - General arrangement of a typical
boat with the hull made of
reinforced material
Annex E (informative) - General arrangement of a typical
paddle boat/kayak
Annex F (informative) - Examples of typical products forming
Class E
Bibliography
Pertains to CLASS E floating leisure articles for use on and in water according to EN 15649-1 regardless whether the buoyancy is achieved by inflation or inherent buoyant material.
| Committee |
SW/136
|
| DevelopmentNote |
Supersedes 07/30161910 DC. (12/2009)
|
| DocumentType |
Standard
|
| Pages |
36
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This European Standard is applicable for CLASS E floating leisure articles for use on or in water according to EN 15649-1 regardless whether the buoyancy is achieved by inflation or inherent buoyant material. This document (EN 15649-7) is applicable with EN 15649-1 and EN 15649-2. Class E devices are intended for use in bathing areas or in protected and safe shore zones. NOTE 1 Typical products forming class E: - inflatable boats for rowing or paddling of near oval shape with or without transom; - canoes and kayaks; - inflatable boats made from plastic sheets or from reinforced materials; - motor kit/sail kit as additional option. NOTE moving from A to B for pleasure purposes; - staying on the water for relaxing; - moving from shore to the main water craft, transportation of persons and load (tender boat).
| Standards | Relationship |
| EN 15649-7:2009 | Identical |
| EN ISO 6185-1:2001 | Inflatable boats - Part 1: Boats with a maximum motor power rating of 4,5 kW (ISO 6185-1:2001) |
| EN 13138-3:2014 | Buoyant aids for swimming instruction - Part 3: Safety requirements and test methods for swim seats to be worn |
| EN ISO 8665:2017 | Small craft - Marine propulsion reciprocating internal combustion engines - Power measurements and declarations (ISO 8665:2006) |
| EN ISO 6185-2:2001 | Inflatable boats - Part 2: Boats with a maximum motor power rating of 4,5 kW to 15 kW inclusive (ISO 6185-2:2001) |
| ISO 4646:1989 | Rubber- or plastics-coated fabrics — Low-temperature impact test |
| ISO 6185-1:2001 | Inflatable boats Part 1: Boats with a maximum motor power rating of 4,5 kW |
| EN 15649-2:2009+A2:2013 | Floating leisure articles for use on and in the water - Part 2: Consumer information |
| EN 13138-2:2014 | Buoyant aids for swimming instruction - Part 2: Safety requirements and test methods for buoyant aids to be held |
| EN ISO 13857:2008 | Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) |
| EN ISO 179-1:2010 | Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2010) |
| ISO 6185-3:2014 | Inflatable boats — Part 3: Boats with a hull length less than 8 m with a motor rating of 15 kW and greater |
| ISO 1431-1:2012 | Rubber, vulcanized or thermoplastic Resistance to ozone cracking Part 1: Static and dynamic strain testing |
| EN 71-1:2014 | Safety of toys - Part 1: Mechanical and physical properties |
| EN 15649-1:2009+A2:2013 | Floating leisure articles for use on and in the water - Part 1: Classification, materials, general requirements and test methods |
| EN ISO 6185-3:2014 | Inflatable boats - Part 3: Boats with a hull length less than 8 m with a motor rating of 15 kW and greater (ISO 6185-3:2014) |
| ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| ISO 4892-2:2013 | Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps |
| ISO 8665:2006 | Small craft Marine propulsion reciprocating internal combustion engines Power measurements and declarations |
| ISO 6185-2:2001 | Inflatable boats Part 2: Boats with a maximum motor power rating of 4,5 kW to 15 kW inclusive |
| ISO 3011:1997 | Rubber- or plastics-coated fabrics Determination of resistance to ozone cracking under static conditions |
| EN 837-3:1996 | Pressure gauges - Part 3: Diaphragm and capsule pressure gauges - Dimensions, metrology, requirements and testing |
| EN 13138-1:2014 | Buoyant aids for swimming instruction - Part 1: Safety requirements and test methods for buoyant aids to be worn |
| EN ISO 4892-2:2013 | Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps (ISO 4892-2:2013) |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.