BS EN 1845:2007

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or protective measures
  5.1 General
  5.2 Common requirements for all footwear moulding machines
      5.2.1 Mechanical hazards
      5.2.2 Electrical equipment
      5.2.3 Thermal protection
      5.2.4 Noise control
      5.2.5 Fumes detrimental to health
      5.2.6 Ergonomics
      5.2.7 Pressurized fluid systems
      5.2.8 Control systems
      5.2.9 Additional safety devices
      5.2.10 Material feeding
      5.2.11 Auxiliary equipment
      5.2.12 Integrated manufacturing systems
      5.2.13 Aids for transportation
  5.3 Requirements for specific types of footwear moulding
      machines
      5.3.1 Direct-on sole moulding machines
      5.3.2 Unit sole and footwear component moulding machines
      5.3.3 Full shoe and boot moulding machines with rotary
            configuration
6 Verification of safety requirements and/or measures
7 Information for use
  7.1 General
  7.2 Signal and warning devices
  7.3 Instruction handbook
  7.4 Declared noise emission values
  7.5 Marking
Annex A (normative) - Requirements for guards
      A.1 Fixed covers
      A.2 Movable enclosing guards and movable covers
      A.3 Fencing
Annex B (normative) - Requirements for interlocking systems
Annex C (normative) - Requirements for trip devices
      C.1 Mechanical trip device with one position sensor
      C.2 Electro-sensitive protective devices (ESPD) with normal
          level
      C.3 Electro-sensitive protective devices (ESPD) with high
          level
      C.4 Electro-sensitive protective devices (high level) with
          control function
      C.5 Electro-sensitive protective device (ESPD) used as danger
          area protection
      C.6 Active-opto-electric protective devices (laser scanner)
Annex D (normative) - Requirements for two-hand control devices
      D.1 Two-hand control devices (normal level)
      D.2 Two-hand control devices (high level)
Annex E (normative) - Requirements for hold-to-run control devices
      E.1 Hold-to-run control devices (stop function, Figure E.1,
          illustration of the principle for pneumatic systems)
      E.2 Hold-to-run control devices (reverse function, Figure E.2,
          illustration of the principle for pneumatic systems)
Annex F (normative) - Requirements for pressure sensitive mats (PSM)
        and floors (PSF)
Annex G (normative) - Requirements for controls for mould closing
      G.1 Power interlocking system
      G.2 Control systems category 1 of EN ISO 13849-1
Annex H (normative) - Requirements for two-fault safety machine control
        systems
Annex I (normative) - Control measures for the suspension of safeguards
        relating to integrated manufacturing systems
Annex J (normative) - Requirements for control guards (interlocking
        guard with start function)
Annex K (normative) - Temperatures of burn threshold
Annex L (normative) - Noise test code for footwear moulding machines
      L.1 Scope
      L.2 Definitions
          L.2.1 Material
          L.2.2 Processing temperature
          L.2.3 Test cycle
          L.2.4 Operator standing area (operating area)
      L.3 Description of machinery family
      L.4 Measurement of A-weighted sound power level
      L.5 Measurement of A-weighted emission sound pressure level
          L.5.1 Position of microphone for determination of A-weighted
                emission sound pressure level at the workstation
      L.6 Operating conditions
      L.7 Measurement uncertainties
      L.8 Documentation
Annex M (normative) - Important considerations relating to integrated
        manufacturing systems
      M.1 Project organisation
      M.2 Application of a safety strategy
      M.3 Risk assessment
      M.4 Requirements for documentation
      M.5 Starting
      M.6 Emergency stop
Annex ZA (informative) - Relationship between this European Standard
         and the essential requirements of EU Directive 98/37/EC
Annex ZB (informative) - Relationship between this European Standard
         and the Essential Requirements of EU Directive 2006/42/EC
Bibliography

Applies to footwear moulding machines, which are intended for use in the shoe industry for the production of footwear and footwear components. It also defines safety requirements for construction, transport, installation, adjustment, setting, teaching or process change-over, operation, cleaning, maintenance, decommissioning, dismantling and, as far as safety is concerned, disposal for machines.

This European Standard applies to footwear moulding machines which are intended for use in the shoe industry for the production of footwear and footwear components. These machines are: - direct-on sole moulding machines (see Figures 1, 2 and 3); - unit sole and footwear component moulding machines (see Figures 4 to 10); - full shoe and boot moulding machines (see Figure 11). This European Standard applies also to the mentioned machines when used for other products than footwear and footwear components, as far as these products require no other changes than a different mould. 1.2 This European Standard specifies safety requirements for construction, transport, installation, adjustment, setting, teaching or process change-over, operation, cleaning, maintenance, decommissioning, dismantling and, as far as safety is concerned, disposal for machines mentioned in l.1. It deals with all significant hazards, hazardous situations and events relevant to footwear moulding machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). 1.3 The following machines are excluded from the scope of this European Standard unless used for direct-on sole moulding or reaction moulding: - moulding machines with static injection units and static mould stations (clamping units); - moulding machines with static metering and mixing units and mobile stations with linear configuration (mould carriers). 1.4 The European Standard does not deal with hazards created by the mixing and metering unit. NOTE For metering and mixing units, see EN 1612-1. The use of machines within the scope of this European Standard in industries other than those specified in 1.1 may give rise to hazards not considered during its preparation. NOTE For this application see also EN 201 and prEN 1612-2. 1.5 This European Standard also applies to the following additional equipment for material handling and operation which are an integ