I.S. EN 1845:2007

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or protective measures
  5.1 General
  5.2 Common requirements for all footwear moulding machines
      5.2.1 Mechanical hazards
      5.2.2 Electrical equipment
      5.2.3 Thermal protection
      5.2.4 Noise control
      5.2.5 Fumes detrimental to health
      5.2.6 Ergonomics
      5.2.7 Pressurized fluid systems
      5.2.8 Control systems
      5.2.9 Additional safety devices
      5.2.10 Material feeding
      5.2.11 Auxiliary equipment
      5.2.12 Integrated manufacturing systems
      5.2.13 Aids for transportation
  5.3 Requirements for specific types of footwear moulding
      machines
      5.3.1 Direct-on sole moulding machines
      5.3.2 Unit sole and footwear component moulding machines
      5.3.3 Full shoe and boot moulding machines with rotary
            configuration
6 Verification of safety requirements and/or measures
7 Information for use
  7.1 General
  7.2 Signal and warning devices
  7.3 Instruction handbook
  7.4 Declared noise emission values
  7.5 Marking
Annex A (normative) Requirements for guards
      A.1 Fixed covers
      A.2 Movable enclosing guards and movable covers
      A.3 Fencing
Annex B (normative) Requirements for interlocking systems
Annex C (normative) Requirements for trip devices
      C.1 Mechanical trip device with one position sensor
      C.2 Electro-sensitive protective devices (ESPD) with normal
          level
      C.3 Electro-sensitive protective devices (ESPD) with high
          level
      C.4 Electro-sensitive protective devices (high level) with
          control function
      C.5 Electro-sensitive protective device (ESPD) used as danger
          area protection
      C.6 Active-opto-electric protective devices (laser scanner)
Annex D (normative) Requirements for two-hand control devices
      D.1 Two-hand control devices (normal level)
      D.2 Two-hand control devices (high level)
Annex E (normative) Requirements for hold-to-run control devices
      E.1 Hold-to-run control devices (stop function, Figure E.1,
          illustration of the principle for pneumatic systems)
      E.2 Hold-to-run control devices (reverse function, Figure E.2,
          illustration of the principle for pneumatic systems)
Annex F (normative) Requirements for pressure sensitive mats (PSM)
        and floors (PSF)
Annex G (normative) Requirements for controls for mould closing
      G.1 Power interlocking system
      G.2 Control systems category 1 of EN ISO 13849-1
Annex H (normative) Requirements for two-fault safety machine control
        systems
Annex I (normative) Control measures for the suspension of safeguards
        relating to integrated manufacturing systems
Annex J (normative) Requirements for control guards (interlocking
        guard with start function)
Annex K (normative) Temperatures of burn threshold
Annex L (normative) Noise test code for footwear moulding machines
      L.1 Scope
      L.2 Definitions
          L.2.1 Material
          L.2.2 Processing temperature
          L.2.3 Test cycle
          L.2.4 Operator standing area (operating area)
      L.3 Description of machinery family
      L.4 Measurement of A-weighted sound power level
      L.5 Measurement of A-weighted emission sound pressure level
          L.5.1 Position of microphone for determination of A-weighted
                emission sound pressure level at the workstation
      L.6 Operating conditions
      L.7 Measurement uncertainties
      L.8 Documentation
Annex M (normative) Important considerations relating to integrated
        manufacturing systems
      M.1 Project organisation
      M.2 Application of a safety strategy
      M.3 Risk assessment
      M.4 Requirements for documentation
      M.5 Starting
      M.6 Emergency stop
Annex ZA (informative) Relationship between this European Standard
         and the essential requirements of EU Directive 98/37/EC
Annex ZB (informative) Relationship between this European Standard
         and the Essential Requirements of EU Directive 2006/42/EC
Bibliography

Applicable to footwear moulding machines which are intended for use in the shoe industry for the production of footwear and footwear components.