Skip to content
Please enter a keyword to search

  • BS EN 60297-5-103:2001

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Mechanical structures for electronic equipment. Dimensions of mechanical structures of the 482.6 mm (19 in) series. Subracks and associated plug-in units Electrostatic discharge protection

    Available format(s):  Hardcopy, PDF

    Superseded date:  30-05-2008

    Language(s):  English

    Published date:  15-08-2001

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Introduction
    Clause
    1 Scope and object
    2 Normative references
    3 Definitions
    4 Extended feature added to IEC 60297-3 and IEC 60927-4
    5 General equipment arrangement
    6 Provision for electrostatic discharge protection
        6.1 Subrack front and/or rear interface dimensions
             for electrostatic discharge protection
        6.2 Plug-in unit interface dimensions for
             electrostatic discharge protection
    Figure 1 - General equipment arrangement - Typical 6U
        subrack front and/or rear mounted plug-in units
        featured with electrostatic discharge protection
    Figure 2 - Subrack guide rail dimensions for the
        electrostatic discharge contact position
    Figure 3 - Printed board discharge strip dimensions
        maintaining ESD contact during connector engagement
     Figure 4 - Printed board discharge strip dimensions
        breaking ESD contact before connector engagement
    Annex ZA (normative) Normative references to international
        publications with their corresponding European
        publications

    Abstract - (Show below) - (Hide below)

    Provides the extended features of electrostatic discharge protection added to subracks and plug-in units according to IEC 60297-3, IEC 60297-4 and IEC 60297-5-107.

    Scope - (Show below) - (Hide below)

    Specifies dimensions which will ensure dimensional interchangeability of subracks and associated plug-in units using the extended function of electrostatic discharge protection added to IEC 60297-3, IEC 60297-4 and IEC 60297-5-107.

    General Product Information - (Show below) - (Hide below)

    Committee EPL/48
    Development Note Also numbered as IEC 60297-5-103. (06/2001) Supersedes 98/231540 DC. (05/2005)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 60297-5-100:2001 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-100: Subracks and associated plug-in units - Design overview
    IEC 60297-5-107:2001 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-107: Subracks and associated plug-in units - Rear-mounted plug-in units
    IEC 61587-1:2016 Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 1: Environmental requirements, test set-up and safety aspects for cabinets, racks, subracks and chassis under indoor condition use and transportation
    IEC 60297-4:1995+AMD1:1999 CSV Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 4: Subracks and associated plug-in units - Additional dimensions
    EN 60297-5-107:2001 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-107: Subracks and associated plug-in units - Rear mounted plug-in units
    EN 61587-1:2017 Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 1: Environmental requirements, test set-up and safety aspects for cabinets, racks, subracks and chassis under indoor condition use and transportation
    IEC 60297-5-100:2001 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-100: Subracks and associated plug-in units - Design overview
    EN 60297-4:1995/A1:1999 MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT - DIMENSIONS OF MECHANICAL STRUCTURES OF THE 482.6 MM (19 IN) SERIES - SUBRACKS AND ASSOCIATED PLUG-IN UNITS - ADDITIONAL DIMENSIONS
    HD 493.3 : 200S2 DIMENSIONS OF MECHANICAL STRUCTURES OF THE 482.6 MM (19 IN) SERIES - SUBRACKS AND ASSOCIATED PLUG-IN UNITS
    IEC 60917-1:1998+AMD1:2000 CSV Modular order for the development of mechanical structures for electronic equipment practices - Part 1: Generic standard
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective