EN 60297-5-103:2001

Superseded

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View superseded by

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-103: Subracks and associated plug-in units - Electrostatic discharge protection

Available format(s):

Superseded date: 17-09-2004

Language(s):

Published date: 13-04-2001

Publisher: European Committee for Standards - Electrical

Pure ENs are not available for sale, please purchase a suitable national adoption

Table of Contents - (Show below) - (Hide below)

Introduction
Clause
1 Scope and object
2 Normative references
3 Definitions
4 Extended feature added to IEC 60297-3 and IEC 60927-4
5 General equipment arrangement
6 Provision for electrostatic discharge protection
    6.1 Subrack front and/or rear interface dimensions
         for electrostatic discharge protection
    6.2 Plug-in unit interface dimensions for
         electrostatic discharge protection
Figure 1 - General equipment arrangement - Typical 6U
    subrack front and/or rear mounted plug-in units
    featured with electrostatic discharge protection
Figure 2 - Subrack guide rail dimensions for the
    electrostatic discharge contact position
Figure 3 - Printed board discharge strip dimensions
    maintaining ESD contact during connector engagement
Figure 4 - Printed board discharge strip dimensions
    breaking ESD contact before connector engagement
Annex ZA (normative) Normative references to international
    publications with their corresponding European
    publications

Abstract - (Show below) - (Hide below)

Specifies dimensions which will ensure dimensional interchangeability of subracks and associated plug-in units using the extended function of electrostatic discharge protection added to EN 60297-3, EN 60297-4 and EN 60297-5-107.

General Product Information - (Show below) - (Hide below)

Committee	CLC/SR 48D
Document Type	Standard
ISBN
Pages
Published
Publisher	European Committee for Standards - Electrical
Status	Superseded
Superseded By	EN 60297-3-101:2004
Supersedes	EN 60297-5-104:2001

National Adoptions - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
NBN EN 60297 5-103 : 2001	Identical
NEN EN IEC 60297-5-103 : 2001	Identical
CEI EN 60297-5-103 : 1ED 2002	Identical
UNE-EN 60297-5-103:2001	Identical
SN EN 60297-5-103 : 2001	Identical
IEC 60297-5-103:2001	Identical
I.S. EN 60297-5-103:2001	Identical
BS EN 60297-5-103:2001	Identical
DIN EN 60297-5-103:2001-11	Identical

Standards Referenced By This Book - (Show below) - (Hide below)

BS EN 60297-5-100:2001	Mechanical structures for electronic equipment. Dimensions of mechanical structures of the 482.6 mm (19 in) series. Subracks and associated plug-in units Design overview
BS EN 60297-5-105:2001	Mechanical structures for electronic equipment. Dimensions of mechanical structures of the 482.6 mm (19 in) series. Subracks and associated plug-in units Alignments and/or earth pin

Standards Referencing This Book - (Show below) - (Hide below)

IEC 60297-5-107:2001	Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-107: Subracks and associated plug-in units - Rear-mounted plug-in units
IEC 61587-1:2016	Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 1: Environmental requirements, test set-up and safety aspects for cabinets, racks, subracks and chassis under indoor condition use and transportation
IEC 60297-4:1995+AMD1:1999 CSV	Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 4: Subracks and associated plug-in units - Additional dimensions
IEC 60297-5-100:2001	Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-100: Subracks and associated plug-in units - Design overview
IEC 60917-1:1998+AMD1:2000 CSV	Modular order for the development of mechanical structures for electronic equipment practices - Part 1: Generic standard

Categories associated with this Standard - (Show below) - (Hide below)

Sub-Categories associated with this Standard - (Show below) - (Hide below)

Sorry this product is not available in your region.

Add To Cart