BS EN 62282-3-3:2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Fuel cell technologies Stationary fuel cell power systems. Installation
Hardcopy , PDF
30-11-2012
English
30-09-2008
Important note : Users cannot be edited or removed once added to your Multi user PDF.
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General safety requirements and strategy
5 Siting considerations
5.1 General siting
5.2 Outdoor installations
5.3 Indoor installations
5.3.1 Large fuel cell power systems
5.3.2 Small fuel cell power systems
5.4 Rooftop installation
6 Ventilation and exhaust
6.1 General
6.2 Ventilation
6.3 Exhaust system
6.4 Process purging and venting
7 Fire protection and gas detection
7.1 Fire protection and detection
7.1.1 Site fire protection
7.1.2 Combustible gas detection (indoor installations only)
7.2 Fire prevention and emergency planning
8 Interconnections with site interfaces
8.1 General
8.2 Connections to fuel supplies - General
8.3 Fuel shut off and piping
8.4 Connections to auxiliary media supply and media disposal
8.4.1 Combustible auxiliary gases
8.4.2 Non combustible or inert auxiliary gases
8.4.3 Water
8.4.4 Waste water disposal
8.4.5 Discharge pipe
9 Environmental requirements
10 Approval tests
10.1 Gas leakage
10.2 Site specific shutdown devices
11 Maintenance tests
12 Documentation
12.1 Markings and instructions
12.2 Inspection checklist
12.3 Installation manual
12.4 User's information manual
12.5 Maintenance manual
Annex ZA (normative) Normative references to international
publications with their corresponding European
publications
Gives minimum safety requirements for the installation of indoor and outdoor stationary fuel cell power systems in compliance with IEC 62282-3-1.
| Committee |
GEL/105
|
| DevelopmentNote |
Supersedes 05/30089621 DC. (09/2008)
|
| DocumentType |
Standard
|
| Pages |
20
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
Provides minimum safety requirements for the installation of indoor and outdoor stationary fuel cell power systems in compliance with IEC 62282-3-1; applies to the installation of systems intended for electrical connection to mains directly or with a transfer switch, or intended for a stand-alone power distribution system, or intended to provide AC or DC power.
| Standards | Relationship |
| IEC 62282-3-3:2007 | Identical |
| EN 62282-3-3:2008 | Identical |
| IEC 60079-10:2002 | Electrical apparatus for explosive gas atmospheres - Part 10: Classification of hazardous areas |
| IEC 62282-3-1:2007 | Fuel cell technologies - Part 3-1: Stationary fuel cell power systems - Safety |
| IEC 61779-6:1999 | Electrical apparatus for the detection and measurement of flammable gases - Part 6: Guide for the selection, installation, use and maintenance of apparatus for the detection and measurement of flammable gases |
| EN 61779-4:2000 | Electrical apparatus for the detection and measurement of flammable gases - Part 4: Performance requirements for group II apparatus indicating a volume fraction up to 100 % lower explosive limit |
| EN 61511-3:2017 | Functional safety - Safety instrumented systems for the process industry sector - Part 3: Guidance for the determination of the required safety integrity levels |
| IEC 61779-4:1998 | Electrical apparatus for the detection and measurement of flammable gases - Part 4: Performance requirements for group II apparatus indicating up to 100% lower explosive limit |
| IEC 61511-3:2016 | Functional safety - Safety instrumented systems for the process industry sector - Part 3: Guidance for the determination of the required safety integrity levels |
| ISO 14121:1999 | Safety of machinery Principles of risk assessment |
| EN 60079-10:2003 | Electrical apparatus for explosive gas atmospheres - Part 10: Classification of hazardous areas |
| EN 62282-3-1 : 2007 | FUEL CELL TECHNOLOGIES - PART 3-1: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.