BS EN ISO 11298-3:2011
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
View Superseded by
Plastics piping systems for renovation of underground water supply networks Lining with close-fit pipes
24-10-2018
31-05-2011
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Pipes at the "M" stage
6 Fittings at the "M" stage
7 Ancillary components
8 Fitness for purpose of the installed lining system at
the "I" stage
9 Installation practice
Annex A (normative) - Factory-folded heat-reverted
polyethylene (PE) pipe - Determination of memory
ability
Bibliography
Describes, in conjunction with ISO 11298-11, requirements and test methods for close-fit lining systems intended to be used for the renovation of water supply networks, which transport water intended for human consumption, including raw water intake pipelines.
| Committee |
PRI/88
|
| DevelopmentNote |
Supersedes BS EN 14409-3 & 08/30174014 DC. (05/2011)
|
| DocumentType |
Standard
|
| PublisherName |
British Standards Institution
|
| Status |
Withdrawn
|
| SupersededBy | |
| Supersedes |
This part of ISO 11298, in conjunction with ISO 11298-1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of water supply networks, which transport water intended for human consumption, including raw water intake pipelines.
It is applicable to polyethylene (PE) pipe for both independent and interactive pressure pipe liners as well as associated fittings and joints for the construction of the lining system.
| Standards | Relationship |
| ISO 11298-3:2010 | Identical |
| EN ISO 11298-3:2011 | Identical |
| EN 12201-4:2012 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 4: Valves |
| ISO 4427-3:2007 | Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 3: Fittings |
| ISO 4427-1:2007 | Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 1: General |
| ISO 11295:2017 | Classification and information on design and applications of plastics piping systems used for renovation and replacement |
| ISO 12176-1:2017 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion |
| ISO 3:1973 | Preferred numbers Series of preferred numbers |
| ISO 4427-5:2007 | Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 5: Fitness for purpose of the system |
| ISO 12176-2:2008 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2: Electrofusion |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| ISO 11298-1:2010 | Plastics piping systems for renovation of underground water supply networks Part 1: General |
| ISO 497:1973 | Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers |
| ISO 4427-2:2007 | Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 2: Pipes |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.