BS EN ISO 1179-2:2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Connections for general use and fluid power. Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E)
Hardcopy , PDF
25-11-2022
English
30-11-2013
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Dimensions
5 Requirements
6 Elastomeric seals
7 Test methods
8 Designation of stud ends
9 Identification statement (reference to this part of ISO 1179)
Annex A (normative) - Test data form for ISO 1179-1 port and
ISO 1179-2 stud ends
Bibliography
Describes dimensions, performance requirements and test procedures for heavy-duty (S series) and light-duty (L series) stud ends with ISO 228-1 threads and the elastomeric sealing (type E) that is used with them.
| Committee |
MCE/18/-/4
|
| DevelopmentNote |
Supersedes 01/714273 DC & 05/30135258 DC. (02/2009) Supersedes 12/30260523 DC. (11/2013)
|
| DocumentType |
Standard
|
| Pages |
22
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This part of ISO1179 specifies dimensions, performance requirements and test procedures for heavy-duty (Sseries) and light-duty (Lseries) stud ends with ISO228-1 threads and the elastomeric sealing (typeE) that is used with them.
Heavy-duty (Sseries) stud ends with typeE sealing in accordance with this part of ISO1179 can be used at working pressures up to 63MPa (630bar). Light-duty (Lseries) stud ends with typeE sealing in accordance with this part of ISO1179 can be used at working pressures up to 25MPa (250bar). The permissible working pressure depends upon size, materials, design, working conditions, application, etc.
Conformance to the dimensional information in this part of ISO1179 does not guarantee rated performance. It is the responsibility of each manufacturer to perform testing according to the specification contained in this part of ISO1179 in order to ensure that components made to this part of ISO1179 comply with the performance ratings.
NOTE1 This part of ISO1179 applies to connectors detailed in ISO8434-1 and ISO8434-2.
NOTE2 The introduction of this part of ISO1179 gives recommendations for ports and stud ends to be used for new designs in hydraulic and pneumatic fluid power applications.
| Standards | Relationship |
| EN ISO 1179-2:2013 | Identical |
| ISO 1179-2:2013 | Identical |
| BS 4368-1(1998) : 1998 | METALLIC TUBE CONNECTORS FOR FLUID POWER AND GENERAL USE - PART 1: SPLIT COLLET COMPRESSION FITTINGS |
| 14/30284897 DC : 0 | BS 4368-1(1998) + A1 - METALLIC TUBE CONNECTORS FOR FLUID POWER AND GENERAL USE - PART 1: SPLIT COLLET COMPRESSION FITTINGS |
| ISO 11926-2:1995 | Connections for general use and fluid power — Ports and stud ends with ISO 725 threads and O-ring sealing — Part 2: Heavy-duty (S series) stud ends |
| ISO 8434-1:2007 | Metallic tube connections for fluid power and general use Part 1: 24 degree cone connectors |
| ISO 5598:2008 | Fluid power systems and components Vocabulary |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| ISO 9974-1:1996 | Connections for general use and fluid power Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing Part 1: Threaded ports |
| ISO 9974-3:1996 | Connections for general use and fluid power — Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing — Part 3: Stud ends with metal-to-metal sealing (type B) |
| ISO 9974-2:1996 | Connections for general use and fluid power — Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing — Part 2: Stud ends with elastomeric sealing (type E) |
| ISO 8434-2:2007 | Metallic tube connections for fluid power and general use — Part 2: 37 degree flared connectors |
| ISO 6149-3:2006 | Connections for hydraulic fluid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 3: Dimensions, design, test methods and requirements for light-duty (L series) stud ends |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| ISO 1302:2002 | Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation |
| ISO 19879:2010 | Metallic tube connections for fluid power and general use Test methods for hydraulic fluid power connections |
| ISO 6149-2:2006 | Connections for hydraulic fluid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 2: Dimensions, design, test methods and requirements for heavy-duty (S series) stud ends |
| ISO 286-1:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits |
| ISO 6149-1:2006 | Connections for hydraulic fluid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 1: Ports with truncated housing for O-ring seal |
| ISO 8434-4:1995 | Metallic tube connections for fluid power and general use Part 4: 24 degree cone connectors with O-ring weld-on nipples |
| ISO 286-2:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts |
| ISO 11926-3:1995 | Connections for general use and fluid power — Ports and stud ends with ISO 725 threads and O-ring sealing — Part 3: Light-duty (L series) stud ends |
| ISO 16030:2001 | Pneumatic fluid power — Connections — Ports and stud ends |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| ISO 11926-1:1995 | Connections for general use and fluid power Ports and stud ends with ISO 725 threads and O-ring sealing Part 1: Ports with O-ring seal in truncated housing |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.