Skip to content
Please enter a keyword to search

  • BS EN ISO 12215-9:2012

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Small craft. Hull construction and scantlings Sailing craft appendages

    Available format(s):  Hardcopy, PDF

    Superseded date:  24-10-2018

    Language(s):  English

    Published date:  30-06-2012

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols
    5 Design stresses
    6 Structural components to be assessed
    7 Load cases
    8 Computational methods
    9 Compliance
    Annex A (normative) - Application declaration
    Annex B (informative) - Information on metal for appendages
            and fasteners and "established practice" for
            fastening and welding
    Annex C (informative) - "Established practice" structural
            arrangement for ballast keels
    Annex D (informative) - "Established practice" calculation
            of keel fin strength (fixed or canting) and fixed
            ballast keel connected by bolts
    Annex E (informative) - Geometrical properties of some typical
            appendage foil shapes
    Annex F (informative) - Simplified fatigue strength assessment
    Bibliography
    Annex ZA (informative) - Relationship between this European
             Standard and the Essential Requirements of EU
             Directive 94/25/EC as amended by Directive 2003/44/EC

    Abstract - (Show below) - (Hide below)

    Describes the loads and specifies the scantlings of sailing craft appendages on monohull sailing craft with a length of hull, L[H], of up to 24 m, measured according to ISO 8666.

    General Product Information - (Show below) - (Hide below)

    Committee GME/33
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    2003/44/EC : 2003 COR 1 2006 DIRECTIVE 2003/44/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 16 JUNE 2003 AMENDING DIRECTIVE 94/25/EC ON THE APPROXIMATION OF THE LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO RECREATIONAL CRAFT
    ISO 12215-5:2008 Small craft Hull construction and scantlings Part 5: Design pressures for monohulls, design stresses, scantlings determination
    ISO 3506-1:2009 Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs
    ISO 16143-2:2014 Stainless steels for general purposes Part 2: Corrosion-resistant semi-finished products, bars, rods and sections
    GL I-1-1 : JAN 2016 RULES FOR CLASSIFICATION AND CONSTRUCTION - 1: SHIP TECHNOLOGY - PART 1: SEAGOING SHIPS - CHAPTER 1: HULL STRUCTURES
    EN 10088-3:2014 Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
    ISO 12217-2:2015 Small craft — Stability and buoyancy assessment and categorization — Part 2: Sailing boats of hull length greater than or equal to 6 m
    1994/25/EC : 1994 DIRECTIVE 94/25/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 16 JUNE 1994 ON THE APPROXIMATION OF THE LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO RECREATIONAL CRAFT
    ISO 8666:2016 Small craft Principal data
    NFE 25 030-1 : 2014 FASTENERS - THREADED CONNECTIONS WITH ISO METRIC THREAD - PART 1: DESIGN RULES FOR TENSILE LOADED BOLTED JOINTS - SIMPLIFIED PROCEDURE - FIXATIONS
    ISO 5817:2014 Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections
    ISO 12215-3:2002 Small craft — Hull construction and scantlings — Part 3: Materials: Steel, aluminium alloys, wood, other materials
    EN 10025-6:2004+A1:2009 Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition
    ISO 12215-6:2008 Small craft — Hull construction and scantlings — Part 6: Structural arrangements and details
    ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread
    ABS 0037 : 1994 COR 2012 GUIDE FOR BUILDING AND CLASSING OFFSHORE RACING YACHTS
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective