BS EN ISO 13479:2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Polyolefin pipes for the conveyance of fluids — Determination of resistance to crack propagation — Test method for slow crack growth on notched pipes
Hardcopy , PDF
08-07-2022
English
30-11-2009
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Principle
5 Apparatus
6 Test piece preparation
7 Conditioning
8 Procedure
9 Test report
Annex A (normative) - Ligament thicknesses
Annex B (normative) - Test-pressure levels for
polyethylene
Describes a test method for determining the resistance to slow crack growth of polyolefin pipes, expressed in terms of time to failure in a hydrostatic pressure test on a pipe with machined longitudinal notches in the outside surface.
| Committee |
PRI/88
|
| DevelopmentNote |
Supersedes 94/300559 DC. (11/2005) Supersedes BS 2782-11.1109N(1997). (11/2009)
|
| DocumentType |
Standard
|
| Pages |
16
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This International Standard specifies a test method for determining the resistance to slow crack growth of polyolefin pipes, expressed in terms of time to failure in a hydrostatic pressure test on a pipe with machined longitudinal notches in the outside surface. The test is applicable to pipes of wall thickness greater than 5mm.
| Standards | Relationship |
| ONORM EN ISO 13479 : 2010 | Identical |
| NS EN ISO 13479 : 2009 | Identical |
| NBN EN ISO 13479 : 2009 | Identical |
| NF EN ISO 13479 : 2009 | Identical |
| DIN EN ISO 13479:2010-01 | Identical |
| EN ISO 13479:2009 | Identical |
| ISO 13479:2009 | Identical |
| UNE-EN ISO 13479:2010 | Identical |
| SN EN ISO 13479:2010 | Identical |
| I.S. EN ISO 13479:2009 | Identical |
| NEN EN ISO 13479 : 2009 | Identical |
| UNI EN ISO 13479 : 2009 | Identical |
| BS 8588:2017 | Polyethylene pressure pipe with an aluminium barrier layer and associated fittings for potable water supply in contaminated land. Size 20 mm to 630 mm |
| BS EN 13244-1:2002 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage. Polyethylene (PE) General |
| EN 13244-1:2002 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 1: General |
| EN 13244-3:2002 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 3: Fittings |
| 16/30340367 DC : 0 | BS 8588 - POLYEPTRHEYSLSEUNREE PIPES WITH AN ALUMINIUM BARRIER LAYER AND ASSOCIATED FITTINGS FOR POTABLE WATER SUPPLY IN CONTAMINATED LAND - SIZE 20 MM TO 630 MM |
| BS EN 13244-3:2002 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage. Polyethylene (PE) Fittings |
| BS EN 13244-2:2002 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage. Polyethylene (PE) Pipes |
| EN 13244-2:2002 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 2: Pipes |
| ISO 6108:1978 | Double equal angle cutters with plain bore and key drive |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| ISO 161-1:1996 | Thermoplastics pipes for the conveyance of fluids Nominal outside diameters and nominal pressures Part 1: Metric series |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| ISO 11922-1:1997 | Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.