• BS EN ISO 22475-1:2006

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    Geotechnical investigation and testing. Sampling methods and groundwater measurements Technical principles for execution

    Available format(s):  Hardcopy, PDF

    Superseded date:  01-11-2021

    Language(s):  English

    Published date:  30-04-2007

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
       3.1 Site investigation methods
       3.2 Drilling rigs and equipment
       3.3 Sampling
       3.4 Groundwater measurements
    4 Drilling rigs and ancillary equipment
       4.1 General
       4.2 Requirements for the drilling rigs and equipment
       4.3 Equipment scope
    5 General requirements prior to sampling and groundwater
       measurements
       5.1 General
       5.2 Selection of techniques and methods
       5.3 Requirements for ground investigation sites and
            points
       5.4 Preliminary information needed before starting
            sampling and groundwater measurements
       5.5 Backfilling and site abandonment
       5.6 Safety and special requirements
    6 Soil sampling methods
       6.1 General
       6.2 Categories of soil sampling methods
       6.3 Sampling by drilling (continuous sampling)
       6.4 Sampling using samplers
       6.5 Block sampling
    7 Rock sampling methods
       7.1 General
       7.2 Categories for rock sampling methods
       7.3 Sampling by drilling
       7.4 Block sampling
       7.5 Integral sampling
    8 Groundwater sampling methods for geotechnical purposes
       8.1 General
       8.2 Equipment
       8.3 Techniques of groundwater sampling
    9 Groundwater measuring stations and piezometers
       9.1 General
       9.2 Piezometers
       9.3 Installation of piezometers
       9.4 Maintenance
       9.5 Decommissioning
    10 Groundwater measurements
       10.1 Calibration
       10.2 Performance of the measurements
    11 Handling, transport and storage of samples
       11.1 General
       11.2 Preservation materials and sample containers
       11.3 Handling of samples
       11.4 Labelling of samples
       11.5 Transport of samples
       11.6 Preparation of storage and shipping containers
       11.7 Storage of samples
    12 Report
       12.1 Field report
       12.2 Report of the results
    Annex A (informative) Example of a form for the preliminary
            information on the intended sampling and groundwater
            measurements
    Annex B (informative) Field reports
    Annex C (informative) Drilling and sampling equipment for
            soil and rock
    Annex D (informative) Vacuum bottles for groundwater sampling
    Annex E (informative) Protective measures of piezometers
    Bibliography

    Abstract - (Show below) - (Hide below)

    Deals with the technical principles of sampling of soil, rock and groundwater, and with groundwater measurements, in the context of geotechnical investigation and testing, as described in EN 1997-1 and EN 1997-2.

    General Product Information - (Show below) - (Hide below)

    Committee B/526/3
    Development Note Supersedes 04/30113757 DC. (04/2007) 2006 version re-issued on 31 July 2007 due to typesetting error. (07/2007)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS 6349-1-3:2012 Maritime works General. Code of practice for geotechnical design
    14/30268442 DC : 0 BS 5930 - CODE OF PRACTICE FOR GROUND INVESTIGATIONS
    BS 8006-1(2010) : 2010 CODE OF PRACTICE FOR STRENGTHENED/REINFORCED SOILS AND OTHER FILLS
    BS 5930:2015+A1:2020 Code of practice for ground investigations
    BS 5930(1999) : 1999 CODE OF PRACTICE FOR SITE INVESTIGATIONS
    BS 8006-2(2011) : 2011 CODE OF PRACTICE FOR STRENGTHENED/REINFORCED SOILS - PART 2: SOIL NAIL DESIGN
    BS PAS 8810(2016) : 2016 TUNNEL DESIGN - DESIGN OF CONCRETE SEGMENTAL TUNNEL LININGS - CODE OF PRACTICE
    15/30302283 DC : 0 BS 8081 - GROUTED ANCHORS - CODE OF PRACTICE
    BS 8081:2015 CODE OF PRACTICE FOR GROUTED ANCHORS
    BS 22475-2:2011 Geotechnical investigation and testing. Sampling methods and groundwater measurements Qualification criteria for enterprises and personnel
    12/30250709 DC : 0 BS 6349-1-3 - MARITIME WORKS - PART 1-3: CODE OF PRACTICE FOR PLANNING, DESIGN, CONSTRUCTION AND MAINTENANCE OF STRUCTURES SET IN THE MARITIME ENVIRONMENT - GEOTECHNICS
    BS EN 1997-2 NA : 2007 UK NATIONAL ANNEX TO EUROCODE 7: GEOTECHNICAL DESIGN - PART 2: GROUND INVESTIGATION AND TESTING
    BS 5930:2015 Code of practice for ground investigations
    BS 22475-3:2011 Geotechnical investigation and testing. Sampling methods and groundwater measurements Conformity assessment of enterprises and personnel by third party
    10/30190274 DC : 0 BS 5930+A2 - CODE OF PRACTICE FOR SITE INVESTIGATIONS

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 14688-1:2002 Geotechnical investigation and testing Identification and classification of soil Part 1: Identification and description
    EN 996:1995+A3:2009 Piling equipment - Safety requirements
    ISO 10097-1:1999 Wireline diamond core drilling equipment — System A — Part 1: Metric units
    ISO/TS 22475-2:2006 Geotechnical investigation and testing Sampling methods and groundwater measurements Part 2: Qualification criteria for enterprises and personnel
    EN 791:1995+A1:2009 Drill rigs - Safety
    ISO 14689-1:2003 Geotechnical investigation and testing Identification and classification of rock Part 1: Identification and description
    ISO 22476-3:2005 Geotechnical investigation and testing — Field testing — Part 3: Standard penetration test
    ISO 3552-1:1992 Rotary core diamond drilling equipment — System B — Part 1: Metric units
    EN 1997-2:2007/AC:2010 EUROCODE 7 - GEOTECHNICAL DESIGN - PART 2: GROUND INVESTIGATION AND TESTING
    ISO/TS 22475-3:2007 Geotechnical investigation and testing Sampling methods and groundwater measurements Part 3: Conformity assessment of enterprises and personnel by third party
    ISO 3551-1:1992 Rotary core diamond drilling equipment — System A — Part 1: Metric units
    BS 879-2:1988 Water well casing Specification for thermoplastics tubes for casing and slotted casing
    EN 1997-1:2004/A1:2013 EUROCODE 7: GEOTECHNICAL DESIGN - PART 1: GENERAL RULES
    BS 879-1:1985 Water well casing Specification for steel tubes for casing
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective