BS EN ISO 5270:2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Pulps. Laboratory sheets. Determination of physical properties
Hardcopy , PDF
12-09-2022
English
31-10-2012
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Principle
4 Apparatus
5 Trimmed laboratory sheets
6 Procedures for physical properties ("low grammage" sheets)
7 Procedures for physical properties ("high grammage" sheets)
8 Test report
Bibliography
Describes the relevant International Standards to be used for the determination of physical properties of laboratory sheets made of all kind of pulps.
| Committee |
PAI/11
|
| DevelopmentNote |
Supersedes BS ISO 5270. (05/2000) Supersedes 96/126335 DC. (10/2005)
|
| DocumentType |
Standard
|
| Pages |
20
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This International Standard specifies the relevant International Standards to be used for the determination of physical properties of laboratory sheets made of all kind of pulps. It is applicable to laboratory sheets prepared in accordance with ISO5269-1, ISO5269-2 or ISO5269-3.
In this International Standard, it is left to the pulp producer and the pulp user to agree upon which properties are relevant to be tested. The results are, if applicable, reported in index form.
| Standards | Relationship |
| NEN EN ISO 5270 : 2012 | Identical |
| UNI EN ISO 5270 : 2012 | Identical |
| EN ISO 5270:2012 | Identical |
| ISO 5270:2012 | Identical |
| I.S. EN ISO 5270:2012 | Identical |
| SN EN ISO 5270 : 2012 | Identical |
| UNE-EN ISO 5270:2013 | Identical |
| DIN EN ISO 5270:2013-02 | Identical |
| NBN EN ISO 5270 : 2012 | Identical |
| NF EN ISO 5270 : 2012 | Identical |
| NS EN ISO 5270 : 2012 | Identical |
| ONORM EN ISO 5270 : 2013 | Identical |
| ISO 5269-1:2005 | Pulps — Preparation of laboratory sheets for physical testing — Part 1: Conventional sheet-former method |
| ISO 2493-1:2010 | Paper and board Determination of bending resistance Part 1: Constant rate of deflection |
| ISO 1974:2012 | Paper — Determination of tearing resistance — Elmendorf method |
| ISO 5636-3:2013 | Paper and board — Determination of air permeance (medium range) — Part 3: Bendtsen method |
| ISO 5636-4:2013 | Paper and board — Determination of air permeance (medium range) — Part 4: Sheffield method |
| ISO 11476:2016 | Paper and board Determination of CIE whiteness, C/2 (indoor illumination conditions) |
| ISO 1924-3:2005 | Paper and board Determination of tensile properties Part 3: Constant rate of elongation method (100 mm/min) |
| ISO 7263:2011 | Corrugating medium Determination of the flat crush resistance after laboratory fluting |
| ISO 5626:1993 | Paper Determination of folding endurance |
| ISO 2493-2:2011 | Paper and board Determination of bending resistance Part 2: Taber-type tester |
| ISO 2471:2008 | Paper and board — Determination of opacity (paper backing) — Diffuse reflectance method |
| ISO 9895:2008 | Paper and board — Compressive strength — Short-span test |
| ISO 15361:2000 | Pulps Determination of zero-span tensile strength, wet or dry |
| ISO 2758:2014 | Paper Determination of bursting strength |
| ISO 187:1990 | Paper, board and pulps — Standard atmosphere for conditioning and testing and procedure for monitoring the atmosphere and conditioning of samples |
| ISO 5628:2012 | Paper and board — Determination of bending stiffness — General principles for two-point, three-point and four-point methods |
| ISO 2470-1:2016 | Paper, board and pulps Measurement of diffuse blue reflectance factor Part 1: Indoor daylight conditions (ISO brightness) |
| ISO 5636-5:2013 | Paper and board — Determination of air permeance (medium range) — Part 5: Gurley method |
| ISO 1924-2:2008 | Paper and board — Determination of tensile properties — Part 2: Constant rate of elongation method (20 mm/min) |
| ISO 11475:2017 | Paper and board — Determination of CIE whiteness, D65/10 degrees (outdoor daylight) |
| ISO 536:2012 | Paper and board Determination of grammage |
| ISO 12192:2011 | Paper and board — Determination of compressive strength — Ring crush method |
| ISO 534:2011 | Paper and board — Determination of thickness, density and specific volume |
| ISO 5269-3:2008 | Pulps — Preparation of laboratory sheets for physical testing — Part 3: Conventional and Rapid-Köthen sheet formers using a closed water system |
| ISO 3688:1999 | Pulps — Preparation of laboratory sheets for the measurement of diffuse blue reflectance factor (ISO brightness) |
| ISO 9416:2017 | Paper — Determination of light scattering and absorption coefficients (using Kubelka-Munk theory) |
| ISO 15754:2009 | Paper and board Determination of z-directional tensile strength |
| ISO 5269-2:2004 | Pulps — Preparation of laboratory sheets for physical testing — Part 2: Rapid-Köthen method |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.