BS ISO 10135:1994
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Technical drawings. Simplified representation of moulded, cast and forged parts
Hardcopy , PDF
31-05-2009
English
15-09-2001
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Letter Symbols
5 Line conventions
6 Drawing indications for moulded parts
6.1 Parting surface
6.2 Tool markings
6.3 Special ejector markings identifier
6.4 Mismatch
6.5 Flash
6.6 Extent of specification
6.7 Draft angles
6.8 Tool motion direction
6.9 Part removal direction
6.10 Surface enlargement
6.11 Sinks
6.12 Porosity
6.13 Identification and marking
6.14 Other necessary information
6.15 Special indication for undisturbed surfaces
7 Rules for linear and geometrical dimensioning and tolerancing
7.1 Linear dimensioning and tolerancing
7.2 Geometrical tolerancing
7.3 Datums
7.4 Surface texture
7.5 Edges
Annex A (normative) - Proportions and dimensions of graphical
symbols
Annex B (informative) - Former practice (tapered features)
Annex C (informative) - Relation to the GPS matrix model
Bibliography
Describes rules and conventions for the indications of requirements for moulded parts on technical product documentation.
| Committee |
TPR/1
|
| DevelopmentNote |
Supersedes 00/704035 DC. (06/2005) Supersedes 04/30125936 DC. (01/2008) Renumbered and superseded by BS EN ISO 10135. (05/2009)
|
| DocumentType |
Standard
|
| Pages |
16
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| BS 8888:2008 | Technical product specification. Specification |
| BS 8888:2002 | Technical product documentation (TPD). Specification for defining, specifying and graphically representing products |
| PD 8888:2001 | Technical product documentation (TPD). An interim report |
| BS 8888:2004 | Technical product specification (TPS). Specification |
| BIP 3016 : 2004 | BS 8888(2004) - TECHNICAL PRODUCT SPECIFICATION CD-ROM |
| BS 8888:2006 | Technical product specification (TPS). Specification |
| ISO/TR 14638:1995 | Geometrical product specification (GPS) Masterplan |
| ISO 8015:2011 | Geometrical product specifications (GPS) Fundamentals Concepts, principles and rules |
| ISO 5459:2011 | Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems |
| ISO 2692:2014 | Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR) |
| ISO 128-24:2014 | Technical drawings General principles of presentation Part 24: Lines on mechanical engineering drawings |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| ISO 7083:1983 | TECHNICAL DRAWINGS - SYMBOLS FOR GEOMETRICAL TOLERANCING - PROPORTIONS AND DIMENSIONS |
| ISO 11971:2008 | Steel and iron castings Visual examination of surface quality |
| ISO 15787:2016 | Technical product documentation — Heat-treated ferrous parts — Presentation and indications |
| ISO 81714-1:2010 | Design of graphical symbols for use in the technical documentation of products Part 1: Basic rules |
| ISO 406:1987 | Technical drawings Tolerancing of linear and angular dimensions |
| ISO 1302:2002 | Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation |
| ISO 8062-1:2007 | Geometrical product specifications (GPS) Dimensional and geometrical tolerances for moulded parts Part 1: Vocabulary |
| ISO 128-22:1999 | Technical drawings General principles of presentation Part 22: Basic conventions and applications for leader lines and reference lines |
| ISO 14660-2:1999 | Geometrical Product Specifications (GPS) Geometrical features Part 2: Extracted median line of a cylinder and a cone, extracted median surface, local size of an extracted feature |
| ISO 8785:1998 | Geometrical Product Specification (GPS) — Surface imperfections — Terms, definitions and parameters |
| ISO 128-20:1996 | Technical drawings General principles of presentation Part 20: Basic conventions for lines |
| ISO 129-1:2004 | Technical drawings Indication of dimensions and tolerances Part 1: General principles |
| ISO 14660-1:1999 | Geometrical Product Specifications (GPS) Geometrical features Part 1: General terms and definitions |
| ISO 13715:2017 | Technical product documentation — Edges of undefined shape — Indication and dimensioning |
| ISO 8062:1994 | Castings System of dimensional tolerances and machining allowances |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.