BS ISO 1268-8:2004
Current
The latest, up-to-date edition.
Fibre-reinforced plastics. Methods of producing test plates Compression moulding of SMC and BMC
Hardcopy , PDF
English
02-06-2004
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Health and safety
5 Plate dimensions
6 Apparatus
7 Sampling and conditioning
8 Procedure
9 Stabilization
10 Test plate preparation report
Annex A (informative) Applicable test methods
Bibliography
Provides the general principles and procedures for the compression moulding of test plates from two types of fibre-reinforced thermosetting moulding compound: sheet moulding compound (SMC) and bulk moulding compound (BMC).
| Committee |
PRI/42
|
| DevelopmentNote |
Supersedes 98/122193 DC. (06/2004)
|
| DocumentType |
Standard
|
| Pages |
18
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
This part of ISO1268 specifies the general principles and procedures for the compression moulding of test plates from two types of fibre-reinforced thermosetting moulding compound: sheet moulding compound (SMC) and bulk moulding compound (BMC).
The aim of this part of ISO1268 is to ensure the preparation of flat test plates from which test specimens can be cut (for the relevant test methods, see AnnexA). The plates are produced in such a way that specimens cut from them give representative results when used in these test methods.
| Standards | Relationship |
| ISO 1268-8:2004 | Identical |
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| ISO 4589-3:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 3: Elevated-temperature test |
| ISO 75-1:2013 | Plastics Determination of temperature of deflection under load Part 1: General test method |
| ISO 6603-2:2000 | Plastics — Determination of puncture impact behaviour of rigid plastics — Part 2: Instrumented impact testing |
| ISO 11667:1997 | Fibre-reinforced plastics — Moulding compounds and prepregs — Determination of resin, reinforced-fibre and mineral-filler content — Dissolution methods |
| ISO 527-4:1997 | Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites |
| IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
| ISO 6603-1:2000 | Plastics Determination of puncture impact behaviour of rigid plastics Part 1: Non-instrumented impact testing |
| ISO 295:2004 | Plastics — Compression moulding of test specimens of thermosetting materials |
| ISO 1172:1996 | Textile-glass-reinforced plastics — Prepregs, moulding compounds and laminates — Determination of the textile-glass and mineral-filler content — Calcination methods |
| ISO 11359-2:1999 | Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 3795:1989 | Road vehicles, and tractors and machinery for agriculture and forestry — Determination of burning behaviour of interior materials |
| ISO 1183:1987 | Plastics Methods for determining the density and relative density of non-cellular plastics |
| IEC 60093:1980 | Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials |
| ISO 472:2013 | Plastics — Vocabulary |
| ISO 180:2000 | Plastics Determination of Izod impact strength |
| ISO 2577:2007 | Plastics Thermosetting moulding materials Determination of shrinkage |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| ISO 14125:1998 | Fibre-reinforced plastic composites — Determination of flexural properties |
| ISO 62:2008 | Plastics Determination of water absorption |
| ISO 4589-2:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test |
| IEC 60243-2:2013 | Electric strength of insulating materials - Test methods - Part 2: Additional requirements for tests using direct voltage |
| ISO 75-3:2004 | Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics |
| ISO 8604:1988 | Plastics — Prepregs — Definitions of terms and symbols for designations |
| IEC 60695-2-10:2013 | Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure |
| ISO 12114:1997 | Fibre-reinforced plastics — Thermosetting moulding compounds and prepregs — Determination of cure characteristics |
| ISO 527-1:2012 | Plastics Determination of tensile properties Part 1: General principles |
| EN 1842:1997 | Plastics - Thermoset moulding compounds (SMC - BMC) - Determination of compression moulding shrinkage |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.