BS ISO 7628:2010
Current
The latest, up-to-date edition.
Road vehicles. Thermoplastics tubing for air braking systems
Hardcopy , PDF
English
28-02-2010
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Marking and identification
5 Dimensions
6 Manufacture
7 Installation on the vehicle
8 Testing and requirements
9 Test procedures and requirements
Annex A (normative) - Cold impact apparatus
Annex B (normative) - Tests on tube assemblies
(tube with end fittings)
Annex C (informative) - Method for leak detection
in leak-proof testing
Annex D (informative) - Synopsis of test and
corresponding samples
Bibliography
Describes the minimum requirements for mono wall and multilayer tubing used in air braking systems on road vehicles.
| Committee |
AUE/15
|
| DevelopmentNote |
Supersedes 08/30171587 DC. (02/2010)
|
| DocumentType |
Standard
|
| Pages |
36
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
This International Standard specifies the minimum requirements for mono wall and multilayer tubing used in air braking systems on road vehicles. The conformity of production is the responsibility of the tubing manufacturer.
The marking of the tubing does not automatically imply that the tube assembly (i.e. tube with end fittings) is appropriate for its use on a vehicle.
It is the responsibility of the tube assembler and/or the vehicle manufacturers to ensure that the tests described in AnnexB, relating to the tube assembly itself, are successfully performed.
For the requirements on coiled tube assemblies refer to ISO7375-1 and ISO7375-2.
| Standards | Relationship |
| ISO 7628:2010 | Identical |
| ISO 2719:2016 | Determination of flash point — Pensky-Martens closed cup method |
| ISO 2977:1997 | Petroleum products and hydrocarbon solvents Determination of aniline point and mixed aniline point |
| ISO 1874-1:2010 | Plastics Polyamide (PA) moulding and extrusion materials Part 1: Designation system and basis for specification |
| ISO 1133-1:2011 | Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method |
| ISO 6427:2013 | Plastics — Determination of matter extractable by organic solvents (conventional methods) |
| ISO 7375-2:1998 | Road vehicles — Coiled tube assemblies for air brake connection between towing and towed vehicles — Part 2: Performance requirements |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 1874-2:2012 | Plastics Polyamide (PA) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| ISO 3795:1989 | Road vehicles, and tractors and machinery for agriculture and forestry — Determination of burning behaviour of interior materials |
| ISO 14910-2:2013 | Plastics Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion Part 2: Preparation of test specimens and determination of properties |
| ISO 3146:2000 | Plastics — Determination of melting behaviour (melting temperature or melting range) of semi-crystalline polymers by capillary tube and polarizing-microscope methods |
| ISO 1183-1:2012 | Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 7375-1:1986 | Road vehicles — Coiled pipe assemblies for pneumatic braking connection between motor vehicles and towed vehicles — Part 1: Dimensions |
| ISO 307:2007 | Plastics Polyamides Determination of viscosity number |
| ISO 4892-4:2013 | Plastics — Methods of exposure to laboratory light sources — Part 4: Open-flame carbon-arc lamps |
| ISO 14910-1:2013 | Plastics Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion Part 1: Designation system and basis for specification |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| ISO 4892-2:2013 | Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps |
| ISO 1133-2:2011 | Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 2: Method for materials sensitive to time-temperature history and/or moisture |
| ISO 4080:2009 | Rubber and plastics hoses and hose assemblies — Determination of permeability to gas |
| ISO 1043-1:2011 | Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics |
| SAE J2260_200411 | Nonmetallic Fuel System Tubing with One or More Layers |
| SAE J1131_199808 | Performance Requirements for SAE J844 Nonmetallic Tubing and Fitting Assemblies Used in Automotive Air Brake Systems |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.