BS ISO 8085-3:2001
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels. Metric series. Specifications Electrofusion fittings
Hardcopy , PDF
31-01-2014
English
29-06-2007
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Material
6 General requirements
7 Geometrical characteristics
8 Mechanical characteristics
9 Physical characteristics
10 Technical file
11 Marking
12 Packaging
Annex A (informative) Examples of typical connector sockets
for electrofusion fittings
Annex B (normative) Formulae for calculating the equivalent
dimensions of non-metric fitting series
Annex C (normative) Short-term pressure test method
Annex D (normative) Tensile test for fitting/pipe assemblies
Bibliography
Gives the requirements for polyethylene electrofusion fittings intended to be used with PE pipes and fittings for the supply of gaseous fuels.
| Committee |
PRI/88
|
| DevelopmentNote |
Supersedes 00/122205 DC (12/2001)
|
| DocumentType |
Standard
|
| Pages |
32
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 8085-3:2001 | Identical |
| ISO 8085-2:2001 | Polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels Metric series Specifications Part 2: Spigot fittings for butt fusion, for socket fusion using heated tools and for use with electrofusion fittings |
| ISO 6964:1986 | Polyolefin pipes and fittings Determination of carbon black content by calcination and pyrolysis Test method and basic specification |
| ISO 13477:2008 | Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test) |
| ISO 3:1973 | Preferred numbers Series of preferred numbers |
| ISO 18553:2002 | Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds |
| ISO/TS 10839:2000 | Polyethylene pipes and fittings for the supply of gaseous fuels — Code of practice for design, handling and installation |
| ISO 13957:1997 | Plastics pipes and fittings — Polyethylene (PE) tapping tees — Test method for impact resistance |
| ISO 13479:2009 | Polyolefin pipes for the conveyance of fluids Determination of resistance to crack propagation Test method for slow crack growth on notched pipes |
| IEC 60364-1:2005 | Low-voltage electrical installations - Part 1: Fundamental principles, assessment of general characteristics, definitions |
| ISO 12176-2:2008 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2: Electrofusion |
| ISO 12162:2009 | Thermoplastics materials for pipes and fittings for pressure applications Classification, designation and design coefficient |
| ISO 13478:2007 | Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Full-scale test (FST) |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| ASTM D 4019 : 1994 : REV A | Standard Test Method for Moisture in Plastics by Coulometric Regeneration of Phosphorus Pentoxide (Withdrawn 2002) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| ISO 13954:1997 | Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm |
| ISO 9356:1989 | Polyolefin pipe assemblies with or without jointed fittings Resistance to internal pressure Test method |
| ISO 13955:1997 | Plastics pipes and fittings — Crushing decohesion test for polyethylene (PE) electrofusion assemblies |
| ISO/TR 10837:1991 | Determination of the thermal stability of polyethylene (PE) for use in gas pipes and fittings |
| ISO 1872-1:1993 | Plastics Polyethylene (PE) moulding and extrusion materials Part 1: Designation system and basis for specifications |
| ISO 497:1973 | Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers |
| EN 12117:1997 | Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships |
| ISO 11413:2008 | Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting |
| ISO 1133:2005 | Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| ISO 13951:2015 | Plastics piping systems Test method for the resistance of plastic pipe/pipe or pipe/fitting assemblies to tensile loading |
| ISO 4437:2007 | Buried polyethylene (PE) pipes for the supply of gaseous fuels Metric series Specifications |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.