• Shopping Cart
    There are no items in your cart

BS PAS 67(2008) : 2008

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

LABORATORY TESTS TO DETERMINE THE HEATING AND ELECTRICAL PERFORMANCE OF HEAT-LED MICRO-COGENERATION PACKAGES PRIMARILY INTENDED FOR HEATING DWELLINGS

Available format(s)

Hardcopy , PDF

Superseded date

28-06-2013

Language(s)

English

Published date

01-01-2008

€303.84
Excluding VAT

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Abbreviations
5 Symbols
6 Micro-cogeneration packages, test modes and test regimes
   6.1 Category of micro-cogeneration package
   6.2 Composition of the micro-cogeneration package to be
         tested
   6.3 Test modes and test regimes
   6.4 Supplementary partial output tests
7 Test laboratory conditions adjacent to the micro-cogeneration
   unit
8 Records for future package surveillance
   8.1 General
   8.2 Manufacturer
   8.3 Manufacturer and test laboratory
   8.4 Test laboratory
9 Actions of the test laboratory upon acceptance of
   micro-cogeneration package
10 Testing principles
   10.1 Introduction
   10.2 Test fuels
         10.2.1 Second and third family gas
         10.2.2 Gas from a bespoke source
         10.2.3 Hydrogen
         10.2.4 Mineral oil
         10.2.5 Other liquid fuels, principally bio-oils
         10.2.6 Other fuels, including unconventional fuel and
                solid fuel
   10.3 Introduction
   10.4 Measurement of energy output
         10.4.1 Space heating heat Q[space]
         10.4.2 Domestic hot water (DHW) Q[DHW]
   10.5 Electrical input and output E[in] and E[out]
   10.6 Case losses Q[case]
   10.7 Flue losses Q[flue]
   10.8 Calculation of the energy content of the micro-cogeneration
         package at the beginning and end of individual tests
         (excluding DHW)
   10.9 Energy balance
   10.10 Instrumentation and laboratory procedures
11 Data to be recorded
12 Test conditions
   12.1 Test sequence
   12.2 Full output test
   12.3 30% output test
         12.3.1 General
         12.3.2 Packages described as being suitable for continuous
                operation
         12.3.3 Packages described as being suitable for uni-modal
                operation
         12.3.4 Packages described as being suitable for bi-modal
                operation
   12.4 10% output test
         12.4.1 General
         12.4.2 Packages described as being suitable for continuous
                operation
         12.4.3 Packages described as being suitable for uni-modal
                operation
         12.4.4 Packages described as being suitable for bi-modal
                operation
   12.5 Supplementary test at other output values (optional)
         12.5.1 General
         12.5.2 Packages described as being suitable for continuous
                operation
         12.5.3 Packages described as being suitable for uni-modal
                operation
         12.5.4 Packages described as being suitable for bi-modal
                operation
   12.6 Test for standby losses
   12.7 DHW only test
         12.7.1 CombiPK with hot water content less than 15 litres
         12.7.2 RegPK
13 Declarations and test results
Annexes
Annex A (normative) - Typical arrangements for micro-cogeneration
                      packages
Annex B (informative) - Method to determine case losses
Annex C (informative) - Direct method of measuring the energy
                        from exhaust gases and condensate
Bibliography

Describes a comprehensive set of test conditions for determining the heating and electrical performance of heat-led micro-cogeneration packages that are primarily intended for use in dwellings.

Committee
ZZ/1
DocumentType
Standard
Pages
65
PublisherName
British Standards Institution
Status
Superseded

BS 845-1:1987 Methods for assessing thermal performance of boilers for steam, hot water and high temperature heat transfer fluids Concise procedure
BS EN 437 : 2003 TEST GASES - TEST PRESSURES - APPLIANCE CATEGORIES
BS 845-2:1987 Methods for assessing thermal performance of boilers for steam, hot water and high temperature heat transfer fluids. Comprehensive procedure
BS EN ISO 9001:2015 Quality management systems. Requirements
BS EN 13203-2:2015 Gas-fired domestic appliances producing hot water Assessment of energy consumption
2004/108/EC : 2004 DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 15 DECEMBER 2004 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO ELECTROMAGNETIC COMPATIBILITY AND REPEALING DIRECTIVE 89/336/EC
2004/8/EC : 2004 DIRECTIVE 2004/8/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 11 FEBRUARY 2004 ON THE PROMOTION OF COGENERATION BASED ON A USEFUL HEAT DEMAND IN THE INTERNAL ENERGY MARKET AND AMENDING DIRECTIVE 1992/42/EEC
BS EN 304:1992 Heating boilers. Test code for heating boilers for atomizing oil burners
92/42/EEC : 1992 AMD 5 2013 COUNCIL DIRECTIVE 92/42/EEC OF 21 MAY 1992 ON EFFICIENCY REQUIREMENTS FOR NEW HOT-WATER BOILERS FIRED WITH LIQUID OR GASEOUS FUELS
BS EN 483 : 2000 GAS-FIRED CENTRAL HEATING BOILERS - TYPE C BOILERS OF NOMINAL HEAT INPUT NOT EXCEEDING 70 KW
PD CEN/TR 1749:2014 European scheme for the classification of gas appliances according to the method of evacuation of the combustion products (types)
BS EN 60751:2008 Industrial platinum resistance thermometers and platinum temperature sensors
1990/396/EEC : 1990 COUNCIL DIRECTIVE OF 29 JUNE 1990 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO APPLIANCES BURNING GASEOUS FUELS

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.