Skip to content
Please enter a keyword to search

  • CEI EN 62329-2 : 2007

    Current The latest, up-to-date edition.

    HEAT SHRINKABLE MOULDED SHAPES - PART 2: METHODS OF TEST

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2007

    Publisher:  Comitato Elettrotecnico Italiano

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Test conditions
    4 Standard test specimens
    5 Dimensions
    6 Density
    7 Heat shock
    8 Bending at low temperature
    9 Dimensional stability on storage
    10 Tensile strength and elongation at break
    11 Secant modulus at 2% elongation
    12 Electric strength
    13 Volume resistivity after damp heat
    14 Permittivity and dissipation factor
    15 Resistance to tracking
    16 Flammability
    17 Oxygen index
    18 Copper corrosion (presence of corrosive
       volatiles)
    19 Colour fastness to light
    20 Resistance to selected fluids
    21 Long term heat ageing (3000 h)
    22 Mass
    23 Heat ageing
    24 Water absorption
    25 Colour stability to heat
    26 Smoke index
    27 Toxicity index
    28 Halogen content
    29 Acid gas generation
    30 Resistance to mould growth
    Bibliography
    Annex ZA (normative) - Normative references to international
             publications with their corresponding European
             publications

    Abstract - (Show below) - (Hide below)

    Gives methods of test for heat-shrinkable moulded shapes in a range of configurations and materials suitable for insulation, environmental sealing, mechanical protection and strain relief for connector/cable terminations and multi-way transitions.

    General Product Information - (Show below) - (Hide below)

    Committee CT 15/112
    Development Note Classificazione CEI 15-212. (03/2007)
    Document Type Standard
    Publisher Comitato Elettrotecnico Italiano
    Status Current

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60243-1:2013 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
    ISO 4589-3:2017 Plastics — Determination of burning behaviour by oxygen index — Part 3: Elevated-temperature test
    ISO 3261:1975 Fire tests — Vocabulary
    IEC 60212:2010 Standard conditions for use prior to and during the testing of solid electrical insulating materials
    IEC 60250:1969 Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths
    IEC 60216-4-2:2000 Electrical insulating materials - Thermal endurance properties - Part 4-2: Ageing ovens - Precision ovens for use up to 300 °C
    IEC 60216-4-1:2006 Electrical insulating materials - Thermal endurance properties - Part 4-1: Ageing ovens - Single-chamber ovens
    ISO 105-B01:2014 Textiles Tests for colour fastness Part B01: Colour fastness to light: Daylight
    IEC 60754-1:2011 Test on gases evolved during combustion of materials from cables - Part 1: Determination of the halogen acid gas content
    IEC 62329-1:2005 Heat shrinkable moulded shapes - Part 1: Definitions and general requirements
    ISO 846:1997 Plastics Evaluation of the action of microorganisms
    IEC 60093:1980 Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
    IEC 60754-2:2011 Test on gases evolved during combustion of materials from cables - Part 2: Determination of acidity (by pH measurement) and conductivity
    IEC 60695-11-10:2013 Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
    ISO 62:2008 Plastics Determination of water absorption
    ISO 37:2017 Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
    ISO 4589-2:2017 Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test
    IEC 60587:2007 Electrical insulating materials used under severe ambient conditions - Test methods for evaluating resistance to tracking and erosion
    ISO 105-A02:1993 Textiles Tests for colour fastness Part A02: Grey scale for assessing change in colour
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective