CEN/TR 14549:2004
Current
The latest, up-to-date edition.
Guide to the use of ISO 15649 and ANSI/ASME B31.3 for piping in Europe in compliance with the Pressure Equipment Directive
10-03-2004
1 Scope
2 Normative References
3 Terms and definitions
4 General
4.1 Scope of the PED
4.2 Responsibilities
4.3 Fluid groups
4.4 Conformity assessment categories
4.5 Conformity assessment procedures
4.6 Hazard analysis
5 Materials
5.1 Material selection and appraisal
5.2 Material certification
6 Design and calculation
6.1 Allowable stresses
6.2 Joint coefficients
6.3 Isolation
7 Fabrication and installation
7.1 Permanent joining (e.g. Welding)
7.2 Traceability
7.3 Documentation
7.3.1 Marking and labelling
7.3.2 Operating instructions
7.3.3 Marking at take-off points
7.3.4 Declaration of conformity
8 Inspection and testing
8.1 Non-destructive tests
8.2 Final inspection
9 Safety devices
Annex A (informative) Checklist of major actions arising from
the PED
Annex B (informative) Key articles in the PED
B.1 Introduction
B.2 Table of Key Articles in the PED
Annex C (informative) Clauses of this guide addressing essential
requirements or other provisions of the PED
Annex D (informative) Comparison of ISO 15649, ANSI/ASME B31.3
and PED annex I (Essential Safety Requirements)
D.1 Introduction
D.2 Comparison tables
D.2.1 Contents of each table
D.2.2 How to use the tables
Annex E (informative) Sources of further information and guidance
E.1 Established guidelines
E.1.1 General
E.1.2 European Commission (CEC) guidelines
E.1.3 Other guidelines
E.2 Other sources of information
E.2.1 Websites
E.2.2 Published Guidance documents
E.2.3 Miscellaneous sources
E.3 Abbreviations
This Guide is intended for use in the petroleum, petrochemical and chemical industries. It identifies and defines a set of common additional and modified requirements to ISO 15649 and ANSI/ASME B31.3 necessitated by the PED. Additional guidance is provided by a suite of annexes (A to E) which are intended to be read independently, but in the context of the main text. These include an actions checklist, tables identifying key requirements of the PED and the corresponding clauses of the ISO/ANSI-ASME standards, and supplementary information.ISO 15649 incorporates ANSI/ASME B31.3 by normative reference and also contains additional common international practice. The relationships are illustrated in Figure 1.
Committee |
CEN/TC 12
|
DocumentType |
Technical Report
|
PublisherName |
Comite Europeen de Normalisation
|
Status |
Current
|
Standards | Relationship |
NEN NPR CEN/TR 14549 : 2004 | Identical |
FD CEN/TR 14549 : 2005 FD | Identical |
I.S. CEN TR 14549:2004 | Identical |
PD CEN/TR 14549:2004 | Identical |
ISO 10438-1:2007 | Petroleum, petrochemical and natural gas industries — Lubrication, shaft-sealing and control-oil systems and auxiliaries — Part 1: General requirements |
I.S. EN ISO 10438-1:2007 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - LUBRICATION, SHAFT-SEALING AND CONTROL-OIL SYSTEMS AND AUXILIARIES - PART 1: GENERAL REQUIREMENTS |
UNI EN ISO 10438-1 : 2009 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - LUBRICATION, SHAFT-SEALING AND CONTROL-OIL SYSTEMS AND AUXILIARIES - PART 1: GENERAL REQUIREMENTS |
ASME B31.3:2016 | PROCESS PIPING |
API 614 REDLINE : 2008 | LUBRICATION, SHAFT-SEALING AND OIL-CONTROL SYSTEMS AND AUXILIARIES |
EI GUIDE. DESIGN & OPER. HEAT EXCHANGERS : 2015-12 | GUIDELINES FOR THE SAFE DESIGN AND OPERATION OF SHELL AND TUBE HEAT EXCHANGERS TO WITHSTAND THE IMPACT OF TUBE FAILURE |
BS EN ISO 10438-1:2003 | Petroleum, petrochemical and natural gas industries. Lubrication, shaft-sealing and control-oil systems and auxiliaries General requirements |
EN ISO 10438-1:2007 | Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 1: General requirements (ISO 10438-1:2007) |
API 614 : 2008 | LUBRICATION, SHAFT-SEALING AND OIL-CONTROL SYSTEMS AND AUXILIARIES |
ISO 15649:2001 | Petroleum and natural gas industries — Piping |
EEMUA 196 : 1999 | VALVE PURCHASER'S GUIDE TO THE EUROPEAN PRESSURE EQUIPMENT DIRECTIVE |
ASME B31.3:2016 | PROCESS PIPING |
ASME QAI 1 : 2010 | QUALIFICATIONS FOR AUTHORIZED INSPECTION |
EN 10204:2004 | Metallic products - Types of inspection documents |
EN 764-4:2014 | Pressure equipment - Part 4: Establishment of technical delivery conditions for metallic materials |
1997/23/EC : 1997 | DIRECTIVE 97/23/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 MAY 1997 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING PRESSURE EQUIPMENT |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.