CSA/ANSI Z21.60-2017 (R2021)/CSA 2.26-2017 (R2021)

Preface
1 Scope
2 Reference publications
3 Definitions
4 Construction
5 Performance
6 Manufacturing and production tests
7 Items unique to the United States
8 Items unique to Canada
Annex A (normative) - Outline of lighting instructions for
        appliances equipped with continuous pilots
Annex B (normative) - Outline of operating instructions for
        appliances equipped with intermittent pilot or
        interrupted pilot systems
Annex C (normative) - Outline of operating instructions for
        appliances equipped with direct ignition systems
Annex D (normative) - Provisions for listed gas appliance
        conversion kits (optional)
Annex E (informative) - Pertinent references to ANSI Y14.15
Annex F (informative) - Wire color designations
Annex G (informative) - Recommended wire color usage
Annex H (informative) - Preferred graphic symbols of
        commonly used items, extracted from the
        Standard for Graphic Symbols for Electrical
        and Electronics Diagrams, ANSI/ IEEE 315,
        and abbreviations for these items
Annex I (informative) - Table of conversion factors

Pertains to decorative gas appliances for installation in solid-fuel burning fireplaces, hereinafter referred to as appliances, which are constructed entirely of new, unused parts and materials, and having input ratings up to and including 400,000 Btu/hr (117228 W).

Preface This is the fourth edition of ANSI Z21.60 • CSA 2.26, Decorative gas appliances for installation in solid- fuel burning fireplaces. It supersedes the previous editions published in 2012, 2003, and 1996. This Standard was prepared by the Z21/CSA Joint Technical Subcommittee on Standards for Decorative Gas Appliances under the jurisdiction of the Z21/83 Technical Committee on Standards for Performance and Installation of Gas Burning Appliances and Related Accessories and the CSA Technical Committee on Gas Appliances and Related Accessories, and had been formally approved by the Technical Committees and the American National Standards Institute. Scope 1.1 This Standard applies to decorative gas appliances for installation in solid-fuel burning fireplaces, (see Clause 3, Definitions), hereinafter referred to as appliances, which are constructed entirely of new, unused parts and materials, and having input ratings up to and including 400,000 Btu/hr (117 228 W). These appliances are: a) for use with natural gas; b) for use with propane gas; c) for use with natural and convertible for use with propane gas (see Clause 3, Definitions); d) for manufactured home (U.S. only) or mobile home installation for use with natural and convertible for use with propane gas; and e) for manufactured home (U.S. only) or mobile home installation for use with propane gas only. The construction of decorative appliances for installation in solid-fuel burning fireplaces for use with the above-mentioned gases is covered under Clause 4. The performance of decorative appliances for installation in solid-fuel burning fireplaces for use with the above-mentioned gases is covered under Clause 5. 1.2 Decorative appliances for installation in solid-fuel burning fireplaces are not thermostatically controlled. 1.3 This Standard does not cover unvented room heaters. 1.4 The use of the term \"appliance\" henceforth in this Standard is in reference to a decorative gas appliance for installation in a solid-fuel burning fireplace. 1.5 If a value for measurement as given in this Standard is followed by an equivalent value in other units, the first stated value is to be regarded as the specification. (Also see Clause 8.3.) 1.6 All references to psi throughout this Standard are to be considered gage pressure unless otherwise specified. 1.7 Clause 7, Items unique to the United States, contains provisions that are unique to the United States. 1.8 Clause 8, Items unique to Canada, contains provisions that are unique to Canada. 1.9 Special construction provisions applicable to an appliance designed for use with an optional listed conversion kit are outlined under Annex D, Provisions for listed gas appliances conversion kits (optional). 1.10 Clause 2 contains a list of standards specifically referenced in this Standard and sources from which they may be obtained. Clause 2 includes both U.S. and Canadian reference standards where applicable. It is the responsibility of the user of this Standard to determine which referenced standard applies based on the requirements of the authority having jurisdiction at the location of the installation.