DD CEN/TS 45545-2:2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Railway applications. Fire protection on railway vehicles Requirements for fire behaviour of materials and components
Hardcopy , PDF
30-11-2015
English
31-05-2009
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
3.1 Definition of parameters
3.2 Explanation of expressions
3.3 Hazard levels
4 Requirements
4.1 Essential
4.2 General
4.3 Listed products
4.4 Non listed products
4.5 Refurbishment and maintenance requirements
4.6 Products to be approved on functional necessity
4.7 Set of material requirements
5 Test properties
5.1 Summary of test methods
5.2 Modifications on test methods used in 5.1
5.3 Testing rules
6 Evaluation of conformity
Annex A (normative) - Standard vandalisation test for seat
coverings
A.1 Introduction
A.2 Apparatus
A.3 Preparation of test specimen
A.4 Test procedure
A.5 Results
A.6 Test report
Annex B (normative) - Fire test method for seating
B.1 General
B.2 Safety warning
B.3 Test facility
B.4 Test specimens
B.5 Test procedure and application of the burner
B.6 Early termination of test
B.7 Test results
B.8 Test report
Annex C (normative) - Testing methods for determination of
toxic gases from railway products
C.1 Introduction
C.2 Method 1 - Test apparatus
C.3 Analysis of fire effluents for Method 1
C.4 Test environment
C.5 Conditioning
C.6 Pre-test conditions for the apparatus for Method 1
C.7 Warnings
C.8 Smoke and gas testing using Method 1
C.9 Data treatment
C.10 Test report for Method 1
C.11 Use of alternative gas analysis techniques to FTIR
C.12 Method 2 - Test apparatus
C.13 Test environment (Method 2)
C.14 Conditioning of Samples
C.15 Test for gases using Method 2
C.16 Calculations of CIT
Annex D (normative) - Protocol for test specimen preparation
in standard tests
D.1 Protocol for specimen preparation for tests
according to EN ISO 5659-2 and ISO 5660-1
D.2 Protocol for specimen preparation of upholstered
furniture assembled products for tests according
to EN ISO 5659-2 and ISO 5660-1
D.3 Protocol for test specimen preparation for flame
spread testing
Annex ZA (informative) - Relationship between this Technical
Specification and the Essential Requirements of
EU Directive 96/48/EC, as amended by 2004/50/EC
Bibliography
Describes the reaction to fire performance requirements for materials and products used on railway vehicles as defined in CEN/TS 45545-1.
| Committee |
FSH/19
|
| DevelopmentNote |
Supersedes 04/19990095 DC. (05/2009)
|
| DocumentType |
Standard
|
| Pages |
76
|
| PublisherName |
British Standards Institution
|
| RevisionOf | |
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| CEN/TS 45545-2:2009 | Identical |
| EN 50266-2-4 : 2001 COR 2002 | COMMON TEST METHODS FOR CABLES UNDER FIRE CONDITIONS - TEST FOR VERTICAL FLAME SPREAD OF VERTICALLY- MOUNTED BUNCHED WIRES OR CABLES - PART 2-4: PROCEDURES - CATEGORY C |
| ISO 5660-1:2015 | Reaction-to-fire tests Heat release, smoke production and mass loss rate Part 1: Heat release rate (cone calorimeter method) and smoke production rate (dynamic measurement) |
| CEN/TS 45545-1:2009 | Railway applications - Fire protection on railway vehicles - Part 1: General |
| CEN/TS 45545-3:2009 | Railway applications - Fire protection on railway vehicles - Part 3: Fire resistance requirements for fire barriers |
| ISO 5658-2:2006 | Reaction to fire tests Spread of flame Part 2: Lateral spread on building and transport products in vertical configuration |
| NFT 90 210 : 2009 | WATER QUALITY - PROTOCOL FOR THE INITIAL METHOD PERFORMANCE ASSESSMENT IN A LABORATORY |
| ISO 1716:2010 | Reaction to fire tests for products Determination of the gross heat of combustion (calorific value) |
| UIC 564-2 : 1991 AMD 2 | REGULATIONS RELATING TO FIRE PROTECTION AND FIREFIGHTING MEASURES IN PASSENGER CARRYING RAILWAY VEHICLES OR ASSIMILATED VEHICLES USED ON INTERNATIONAL SERVICES |
| IEC TS 60695-1-40:2002 | Fire hazard testing - Part 1-40: Guidance for assessing the fire hazard of electrotechnical products - Insulating liquids |
| ISO 5659-2:2017 | Plastics — Smoke generation — Part 2: Determination of optical density by a single-chamber test |
| EN ISO 5659-2:2017 | Plastics - Smoke generation - Part 2: Determination of optical density by a single-chamber test (ISO 5659-2:2017) |
| ISO 11925-2:2010 | Reaction to fire tests Ignitability of products subjected to direct impingement of flame Part 2: Single-flame source test |
| EN ISO 1182:2010 | Reaction to fire tests for products - Non-combustibility test (ISO 1182:2010) |
| ISO 13943:2017 | Fire safety — Vocabulary |
| EN 50266-1:2001 | Common test methods for cables under fire conditions - Test for vertical flame spread of vertically-mounted bunched wires or cables - Part 1: Apparatus |
| EN 60332-1-2:2004/A11:2016 | TESTS ON ELECTRIC AND OPTICAL FIBRE CABLES UNDER FIRE CONDITIONS - PART 1-2: TEST FOR VERTICAL FLAME PROPAGATION FOR A SINGLE INSULATED WIRE OR CABLE - PROCEDURE FOR 1 KW PRE-MIXED FLAME (IEC 60332-1-2:2004/A1:2015) |
| ISO 12952-4:1998 | Textiles Burning behaviour of bedding items Part 4: Specific test methods for the ignitability by a small open flame |
| EN 13238:2010 | Reaction to fire tests for building products - Conditioning procedures and general rules for selection of substrates |
| ISO 6507-3:2005 | Metallic materials Vickers hardness test Part 3: Calibration of reference blocks |
| ISO 1182:2010 | Reaction to fire tests for products Non-combustibility test |
| IEC 60332-1-2:2004+AMD1:2015 CSV | Tests on electric and optical fibre cables under fire conditions - Part 1-2: Test for vertical flame propagation for a single insulatedwire or cable - Procedure for 1 kW pre-mixed flame |
| 2004/50/EC : 2004 | DIRECTIVE 2004/50/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 APRIL 2004 AMENDING COUNCIL DIRECTIVE 1996/48/EC ON THE INTEROPERABILITY OF THE TRANS-EUROPEAN HIGH-SPEED RAIL SYSTEM AND DIRECTIVE 2001/16/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL ON THE INTEROPERABILITY OF THE TRANS-EUROPEAN CONVENTIONAL RAIL SYSTEM |
| NFX 70 100-2 : 2006 | FIRE TESTS - ANALYSIS OF GASEOUS EFFLUENTS - PART 2: TUBULAR FURNACE THERMAL DEGRADATION METHOD |
| ISO/TR 9705-2:2001 | Reaction-to-fire tests Full-scale room tests for surface products Part 2: Technical background and guidance |
| EN ISO 9239-1:2010 | Reaction to fire tests for floorings - Part 1: Determination of the burning behaviour using a radiant heat source (ISO 9239-1:2010) |
| EN ISO 12952-4 : 1998 | TEXTILES - BURNING BEHAVIOUR OF BEDDING ITEMS - PART 4: SPECIFIC TEST METHODS FOR THE IGNITABILITY BY A SMALL OPEN FLAME |
| ISO 19702:2015 | Guidance for sampling and analysis of toxic gases and vapours in fire effluents using Fourier Transform Infrared (FTIR) spectroscopy |
| EN 61034-2:2005/A1:2013 | MEASUREMENT OF SMOKE DENSITY OF CABLES BURNING UNDER DEFINED CONDITIONS - PART 2: TEST PROCEDURE AND REQUIREMENTS (IEC 61034-2:2005/A1:2013) |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| NFX 70 100-1 : 2006 | FIRE TESTS - ANALYSIS OF GASEOUS EFFLUENTS - PART 1: METHODS FOR ANALYSING GASES STEMMING FROM THERMAL DEGRADATION |
| EN 60584-1:2013 | Thermocouples - Part 1: EMF specifications and tolerances |
| ISO 14001:2015 | Environmental management systems — Requirements with guidance for use |
| EN 50305:2002 | Railway applications - Railway rolling stock cables having special fire performance - Test methods |
| ISO 12952-3:1998 | Textiles Burning behaviour of bedding items Part 3: General test methods fot the ignitability by a small open flame |
| EN ISO 13943:2017 | Fire safety - Vocabulary (ISO 13943:2017) |
| EN ISO 14001:2015 | Environmental management systems - Requirements with guidance for use (ISO 14001:2015) |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN ISO 4589-2:2017 | Plastics - Determination of burning behaviour by oxygen index - Part 2: Ambient-temperature test (ISO 4589-2:2017) |
| EN 61034-1:2005/A1:2014 | MEASUREMENT OF SMOKE DENSITY OF CABLES BURNING UNDER DEFINED CONDITIONS - PART 1: TEST APPARATUS (IEC 61034-1:2005/A1:2013) |
| ISO 4589-2:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test |
| EN ISO 12952-3 : 1998 | TEXTILES - BURNING BEHAVIOUR OF BEDDING ITEMS - PART 3: GENERAL TEST METHODS FOR THE IGNITABILITY BY A SMALL OPEN FLAME |
| ISO 9239-1:2010 | Reaction to fire tests for floorings Part 1: Determination of the burning behaviour using a radiant heat source |
| EN ISO 1716:2010 | Reaction to fire tests for products - Determination of the gross heat of combustion (calorific value) (ISO 1716:2010) |
| IEC 61034-2:2005+AMD1:2013 CSV | Measurement of smoke density of cables burning under definedconditions - Part 2: Test procedure and requirements |
| IEC 60584-1:2013 | Thermocouples - Part 1: EMF specifications and tolerances |
| IEC 61034-1:2005+AMD1:2013 CSV | Measurement of smoke density of cables burning under defined conditions - Part 1: Test apparatus |
| 96/48/EC : 1996 | COUNCIL DIRECTIVE 96/48/EC OF 23 JULY 1996 ON THE INTEROPERABILITY OF THE TRANS-EUROPEAN HIGH-SPEED RAIL SYSTEM |
| ISO 11054:2006 | Cutting tools — Designation of high-speed steel groups |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.