• DD CLC/TS 50131-2-7-1:2009

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    ALARM SYSTEMS - INTRUSION AND HOLD-UP SYSTEMS - PART 2-7-1: INTRUSION DETECTORS - GLASS BREAK DETECTORS (ACOUSTIC)

    Available format(s):  Hardcopy, PDF

    Superseded date:  31-10-2013

    Language(s):  English

    Published date:  01-01-2009

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1 Scope
    2 Normative references
    3 Terms, definitions and abbreviations
      3.1 Terms and definitions
      3.2 Abbreviations
    4 Functional requirements
      4.1 Event processing
      4.2 Operational requirements
      4.3 Detection
      4.4 Immunity to false alarm sources
      4.5 Tamper security
      4.6 Electrical requirements
      4.7 Environmental classification and conditions
    5 Marking, identification and documentation
      5.1 Marking and/or identification
      5.2 Documentation
    6 Testing
      6.1 General test conditions
      6.2 Basic detection test
      6.3 Performance tests
      6.4 Switch-on delay, time interval between signals
           and indication of detection
      6.5 Fault condition signals or messages: self tests
      6.6 Tests of immunity to false alarm sources
      6.7 Tamper security
      6.8 Electrical tests
      6.9 Environmental classification and conditions
      6.10 Marking, identification and documentation
    Annex A (informative) - Example of the setup of the test
            room
    Annex B (normative) - Catalogue of standard glass types
    Annex C (normative) - List of small tools suitable for testing
            immunity of casing to attack
    Annex D (normative) - Dimensions & requirements of a
            standard test magnet
      D.1 Normative references
      D.2 Requirements
    Annex E (normative) - Immunity test: Small objects hit
            sensitivity
    Annex F (normative) - Immunity test: Soft objects hit
            sensitivity
    Annex G (normative) - Immunity test: Hard objects hit
            sensitivity
    Annex H (normative) - General testing matrix
    Annex I (normative) - Immunity test: Noise sensitivity
    Annex J (normative) - Performance test setup
      J.1 Performance test setup
      J.2 Alternative performance test setup
    Annex K (informative) - Manipulation test: Resistance to
            re-orientation of adjustable mountings

    Abstract - (Show below) - (Hide below)

    Applies for passive acoustic glass break detectors installed in buildings and provides for security grades 1 to 4, specific or non-specific wired or wire-free detectors and uses environmental classes I to IV.

    General Product Information - (Show below) - (Hide below)

    Comment Closes On
    Committee GW/1/1
    Document Type Draft
    Publisher British Standards Institution
    Revision Of
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    PD 6662:2010 SCHEME FOR THE APPLICATION OF EUROPEAN STANDARDS FOR INTRUSION AND HOLD-UP ALARM SYSTEMS

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60068-1:2013 Environmental testing - Part 1: General and guidance
    EN ISO 527-2:2012 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012)
    EN 60068-1:2014 ENVIRONMENTAL TESTING - PART 1: GENERAL AND GUIDANCE (IEC 60068-1:2013)
    EN ISO 527-1:2012 PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 1: GENERAL PRINCIPLES (ISO 527-1:2012)
    ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
    ISO 2039-2:1987 Plastics Determination of hardness Part 2: Rockwell hardness
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    EN 50131-1:2006/A2:2017 ALARM SYSTEMS - INTRUSION AND HOLD-UP SYSTEMS - PART 1: SYSTEM REQUIREMENTS
    EN 50131-6:2017 ALARM SYSTEMS - INTRUSION AND HOLD-UP SYSTEMS - PART 6: POWER SUPPLIES
    EN 50130-4:2011/A1:2014 ALARM SYSTEMS - PART 4: ELECTROMAGNETIC COMPATIBILITY - PRODUCT FAMILY STANDARD: IMMUNITY REQUIREMENTS FOR COMPONENTS OF FIRE, INTRUDER, HOLD UP, CCTV, ACCESS CONTROL AND SOCIAL ALARM SYSTEMS
    EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
    EN ISO 2039-2 : 1999 PLASTICS - DETERMINATION OF HARDNESS - PART 2 - ROCKWELL HARDNESS
    IEC 60068-2-52:2017 Environmental testing - Part 2-52: Tests - Test Kb: Salt mist, cyclic (sodium chloride solution)
    EN 50130-5:2011 ALARM SYSTEMS - PART 5: ENVIRONMENTAL TEST METHODS
    ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective