DIN 16874:2000-06
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
PIPES AND FITTINGS OF HIGH-DENSITY POLYETHYLENE (PE-HD) FOR CABLE DUCTING - DIMENSIONS AND TECHNICAL DELIVERY CONDITIONS
Hardcopy , PDF
01-09-2019
English
01-01-2000
Foreword
1 Scope
2 Normative references
3 Concepts, quantities, symbols and abbreviations
3.1 Concepts
3.1.1 Virgin material
3.1.2 Reworked material
3.1.3 Reprocessed material
3.1.4 Recycled material
3.2 Quantities and symbols
3.3 Abbreviations
4 Dimensions and designation
4.1 General
4.2 Pipes
4.2.1 General
4.2.2 Tolerances on outside diameter (ovality)
4.3 Sockets
4.4 Fittings
4.4.1 General
4.4.2 Bends
4.4.3 Double sockets and pipe sleeves
5 Material
5.1 Pipes and fittings
5.2 Seals
6 Requirements
6.1 General
6.2 Surface
6.3 Colour
6.4 Dimensions and tolerances
6.5 Resistance to internal pressure
6.6 Melt mass-flow rate
6.7 Heat reversion
6.7.1 Pipes
6.7.2 Fittings
6.8 Leaktightness of pipes, fittings and pipe
assemblies
6.8.1 Resistance to hydrostatic pressure
6.8.2 Airtightness
6.9 Ring seal performance
6.10 Weldability
6.11 Interchangeability
7 Testing
7.1 Surface
7.2 Colour
7.3 Dimensions
7.4 Ovality
7.5 Resistance to internal pressure
7.6 Melt mass-flow rate
7.7 Heat reversion
7.7.1 Pipes
7.7.2 Fittings
7.8 Leaktightness of pipes, fittings and pipe
assemblies
7.8.1 Resistance to hydrostatic pressure
7.8.2 Airtightness
7.9 Ring seal performance
7.10 Weldability
7.11 Marking
7.12 Additional tests
8 Marking
9 Installation instructions
9.1 Structural strength
9.2 Installation of pipes and fittings
Other relevant standards
Specifies the dimensions and technical delivery conditions for high-density polyethylene (PE-HD) pipes and fittings used for cable ducting in telecommunications and high and low voltage electrical power systems for buried conduit systems.
DevelopmentNote |
Suspended until publication of a revised English text, due to a new German edition. (08/2009)
|
DocumentType |
Standard
|
Pages |
12
|
PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
Status |
Superseded
|
DIN 16876:2000-11 | PIPES AND FITTINGS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) FOR DUCTING - DIMENSIONS AND TECHNICAL DELIVERY CONDITIONS |
DIN EN 681-1:2016-07 (Draft) | Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber; German and English version prEN 681-1:2016 |
ISO 161-1:1996 | Thermoplastics pipes for the conveyance of fluids Nominal outside diameters and nominal pressures Part 1: Metric series |
DIN EN 50086-2-4 : 2001 | CONDUIT SYSTEMS FOR ELECTRICAL INSTALLATIONS - PART 2-4: PARTICULAR REQUIREMENTS FOR CONDUIT SYSTEMS BURIED UNDERGROUND |
DIN EN ISO 1133:2000-02 | PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THE THERMOPLASTICS |
DIN 4060:1998-02 | JOINTS OF SEWER AND DRAIN PIPES WITH ELASTOMERIC SEALS - REQUIREMENTS AND TESTING ON JOINTS WITH ELASTOMERIC SEALS |
DIN 8074:1999-08 | POLYETHYLENE (PE) - PIPES PE 63, PE 80, PE 100, PE-HD - DIMENSIONS |
DIN EN 921:1995-01 | PLASTICS PIPING SYSTEMS - THERMOPLASTICS PIPES - DETERMINATION OF RESISTANCE TO INTERNAL PRESSURE AT CONSTANT TEMPERATURE |
DIN 16928:1979-04 | PIPES OF THERMOPLASTIC MATERIALS; PIPE JOINTS, ELEMENTS FOR PIPES, LAYING; GENERAL DIRECTIONS |
ISO 4065:1996 | Thermoplastics pipes Universal wall thickness table |
DIN EN ISO 9001 E : 1994 | QUALITY SYSTEMS - MODEL FOR QUALITY ASSURANCE IN DESIGN/DEVELOPMENT, PRODUCTION, INSTALLATION AND SERVICING |
DIN EN 763:1994-09 | PLASTICS PIPING AND DUCTING SYSTEMS - INJECTION-MOULDED THERMOPLASTICS FITTINGS - TEST METHOD FOR VISUALLY ASSESSING EFFECTS OF HEATING |
DIN 8075:1999-08 | POLYETHYLENE (PE) PIPES - PE 63, PE 80, PE 100, PE-HD - GENERAL QUALITY REQUIREMENTS, TESTING |
DIN EN ISO 9002 E : 1994 | QUALITY SYSTEMS - MODEL FOR QUALITY ASSURANCE IN PRODUCTION, INSTALLATION AND SERVICING |
DIN EN 728:1997-03 | PLASTICS PIPING AND DUCTING SYSTEMS - POLYOLEFIN PIPES AND FITTINGS - DETERMINATION OF OXIDATION INDUCTION TIME |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.