Skip to content
Please enter a keyword to search

  • DIN EN 681-1:2016-07 (Draft)

    Withdrawn A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

    Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber; German and English version prEN 681-1:2016

    Available format(s):  Hardcopy, PDF

    Withdrawn date:  28-03-2022

    Language(s):  German, German - English

    Published date:  01-07-2016

    Publisher:  German Institute for Standardisation (Deutsches Institut für Normung)

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Classification
    4 Requirements
    5 Test pieces and temperature
    6 Quality
    7 Factory product control tests
    8 Storage
    9 Designation
    10 Marking and labelling
    Annexes
    A (normative) Determination of stress relaxation in
        tension
    B (normative) Determination of compression set in hot
        water at 110 Degree C
    C (normative) Determination of splice strength
    D (informative) Guidance on storage of seals
    ZA (informative) Clauses of this European
        Standard addressing the provisions of the
        EU Construction Products Directive

    Abstract - (Show below) - (Hide below)

    This standard is included in DIN Handbook 12/5, 13-2, 13-5, 15-6 and 62-1. Defines requirements for materials used in vulcanized rubber seals for cold potable water supply (up to 50 degree C), hot potable and non-potable water supply (to 110 degree C) and drainage, sewerage and rainwater systems (continuous flow to 45 degree C and intermittent flow up to 95 degree C). Applies to seals for all materials including iron, steel, clay, fibre cement, concrete, reinforced concrete, plastics and glass-reinforced plastic.

    General Product Information - (Show below) - (Hide below)

    Comment Closes On
    Development Note Partly supersedes DIN 4060 issue 12-1988. (09/2000) DRAFT 2016 issued in July 2016. (07/2016)
    Document Type Draft
    Publisher German Institute for Standardisation (Deutsches Institut für Normung)
    Status Withdrawn

    Standards Referenced By This Book - (Show below) - (Hide below)

    DIN 8063-3:2002-06 PIPE JOINTS AND COMPONENTS OF UNPLASTICIZED POLY(VINYLCHLORIDE) (PVC U) FOR PIPES UNDER PRESSURE - PART 3: UNIONS - DIMENSIONS
    DIN V 4034-1:2004-08 PREFABRICATED CONCRETE MANHOLES, UNREINFORCED, STEEL FIBRE AND REINFORCED FOR DRAINS AND SEWERS - TYPE 1 AND TYPE 2 - PART 1: REQUIREMENTS, TEST METHODS AND EVALUATION OF CONFORMITY
    DIN V 1201:2004-08 CONCRETE PIPES AND FITTINGS, UNREINFORCED, STEEL FIBRE AND REINFORCED FOR DRAINS AND SEWERS - TYPE 1 AND TYPE 2 - REQUIREMENTS, TEST METHODS AND EVALUATION OF CONFORMITY
    DIN 28602:2000-05 DUCTILE IRON PIPES AND FITTINGS - BOLTED GLAND JOINTS - ASSEMBLY, SOCKETS, COUNTER RING, SEALING RING, BOLTS AND NUTS
    DIN 16874:2000-06 PIPES AND FITTINGS OF HIGH-DENSITY POLYETHYLENE (PE-HD) FOR CABLE DUCTING - DIMENSIONS AND TECHNICAL DELIVERY CONDITIONS
    DIN 28601:2000-06 DUCTILE IRON PIPES AND FITTINGS - SCREWED SOCKET JOINTS - ASSEMBLY, SOCKETS, SCREW RINGS, SEALING RINGS AND SLIP RINGS
    DIN 28603:2002-05 DUCTILE IRON PIPES AND FITTINGS - PUSH-IN JOINTS - SURVEY, SOCKETS AND GASKETS
    DIN 16831-7:2004-02 Pipe fittinings and joint assemblies for polybutene pressure pipes - Type PB 125 - Part 7: Dimensions of bushings, flanges and sealing elements for socket welding
    DIN HDBK 190 : 3ED 2006 ROHRE, ROHRLEITUNGSTEILE UND ROHRVERBINDUNGEN AUS THERMOPLASTISCHEN KUNSTSTOFFEN
    DIN HDBK 160 : 4ED 2006 WASSERVERSORGUNG 4 - ROHRE, FORMSTUECKE UND ZUBEHOER FUER WASSERLEITUNGEN (B)
    DIN 16962-12:1999-10 PIPE JOINTS AND COMPONENTS OF POLYPROPYLENE (PP) FOR PIPES UNDER PRESSURE, PP-H 100, PP-B 80 AND PP-R 80 - PART 12: FLANGE ADAPTERS, FLANGES, SEALING RINGS FOR SOCKET WELDING; DIMENSIONS
    DIN 16963-11:1999-10 PIPE JOINTS AND COMPONENTS OF POLYETHYLENE (PE) FOR PIPES UNDER PRESSURE, PE 80 AND PE 100 - PART 11: FLANGE ADAPTERS, FLANGES, SEALING RINGS FOR SOCKET WELDING - DIMENSIONS
    DIN 16917-1:2015-10 PIPES AND FITTINGS MADE OF THERMOPLASTIC MATERIALS WITH PROFILED WALL AND SMOOTH PIPE INSIDE - LARGE PIPES OVER DN 1200 FOR UNDERGROUND INSTALLATION - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS
    DIN 8063-3:1980-07 PIPE JOINT ASSEMBLIES AND FITTINGS FOR UNPLASTICIZED POLYVINYL CHLORIDE (PVC-U) PRESSURE PIPES - PART 3: DIMENSIONS OF SCREWED PIPE JOINT ASSEMBLIES

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 3302:1990 Rubber — Dimensional tolerances for use with products
    ISO 3951:1989 Sampling procedures and charts for inspection by variables for percent nonconforming
    EN 45011:1998 General requirements for bodies operating product certification systems (ISO/IEC Guide 65:1996)
    ISO 188:2011 Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
    EN 45011 : 1998 GENERAL REQUIREMENTS FOR BODIES OPERATING PRODUCT CERTIFICATION SYSTEMS
    ISO 2285:2013 Rubber, vulcanized or thermoplastic Determination of tension set under constant elongation, and of tension set, elongation and creep under constant tensile load
    ISO 1431-1:2012 Rubber, vulcanized or thermoplastic Resistance to ozone cracking Part 1: Static and dynamic strain testing
    ISO 9691:1992 Rubber — Recommendations for the workmanship of pipe joint rings — Description and classification of imperfections
    ISO 4661-1:1993 Rubber, vulcanized or thermoplastic Preparation of samples and test pieces Part 1: Physical tests
    ISO 3384:2005 Rubber, vulcanized or thermoplastic Determination of stress relaxation in compression at ambient and at elevated temperatures
    ISO 3387:2012 Rubber Determination of crystallization effects by hardness measurements
    ISO 37:2017 Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
    ISO 471:1995 Rubber Temperatures, humidities and times for conditioning and testing
    ISO 48:2010 Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD)
    ISO 816:1983 Rubber, vulcanized — Determination of tear strength of small test pieces (Delft test pieces)
    EN 45012 : 1998 GENERAL REQUIREMENTS FOR BODIES OPERATING ASSESSMENT AND CERTIFICATION/REGISTRATION OF QUALITY SYSTEMS
    ISO 1629:2013 Rubber and latices — Nomenclature
    EN ISO 9000:2015 Quality management systems - Fundamentals and vocabulary (ISO 9000:2015)
    ISO 1817:2015 Rubber, vulcanized or thermoplastic Determination of the effect of liquids
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective