DIN 17457:1985-07
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
WELDED CIRCULAR AUSTENITIC STAINLESS STEEL TUBES SUBJECT TO SPECIAL REQUIREMENTS - TECHNICAL DELIVERY CONDITIONS
Hardcopy , PDF
01-05-2005
English
12-01-2013
1 Anwendungsbereich
2 Allgemeines
2.1 Begriff
2.2 Prüfklassen
2.3 Ausnutzung der Berechnungsspannung
3 Sorteneintellung
4 Bezeichnung und Bestellung
5 Anforderungen
5.1 Herstellverfahren
5.2 Lieferzustand
5.3 Chemische Zusammensetzung
5.4 Mechanische und technologische Eigenschaften
5.5 Schweisseigung und Schweissbarkeit
5.6 Weiterverarbeitung und Wärmebehandlung
5.7 Korrosionschemisches Verhalten
5.8 Ausführungsart und Aussehern der Oberfläche und
der Schweissverbindung
5.9 Dichtheit
5.10 Zerstörungsfreie Prüfung
5.11 Masse, längenbezogene Massen (Gewichte) und
zulässige Abweichungen
5.12 Physikalische Eigenschaften
6 Prüfungen und Bescheinigungen über Materialprüfungen
6.1 Allgemeines
6.2 Ort der Prüfung
6.3 Prüfunfang
6.4 Probenahme und Probenvorbereitung
6.5 Durchführung der Prüfungen
6.6 Wiederholungsprüfungen
6.7 Bescheinigungen über Materialprüfungen
7 Kennzeichnung
8 Beanstandungen
This standard is included in DIN Handbook 403 and 405. Applies to welded circular tubes and pipes (hereinafter briefly referred to as tubes) subject to special requirements and made from the austenitic stainless steels listed in Table 1. These tubes are predominantly used in the construction of pressure vessles, chemical plant and pipework.
| DocumentType |
Standard
|
| Pages |
16
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| SNV DIN 17457 : 1985 | Identical |
| ISO 2604-5:1978 | Corresponds |
| ISO 9330-6:1997 | Identical |
| ISO 9329-4:1997 | Identical |
| ISO 2604-5:1978 | Identical |
| DIN 8556-1:1986-05 | FILLER METALS FOR WELDING STAINLESS AND HEAT RESISTANT STEELS; DESIGNATION, TECHNICAL DELIVERY CONDITIONS |
| DIN 17441:1997-02 | STAINLESS STEELS - TECHNICAL DELIVERY CONDITIONS FOR COLD ROLLED STRIPS AND SLIT COILS STRIP AND SHEETS CUT FROM SUCH STRIPS FOR PRESSURE PURPOSES |
| DIN 50930-4:1993-02 | CORROSION OF METALS; CORROSION OF METALLIC MATERIALS UNDER CORROSION LOAD BY WATER INSIDE OF TUBES, TANKS AND APPARATUS; EVALUATION OF THE CORROSION LIKELIHOOD OF STAINLESS STEELS |
| DIN 18160-1:2001-12 | CHIMNEYS - PART 1: DESIGN AND PERFORMANCE |
| DIN 28125-1:1989-08 | DN 150 TO DN 600 ROUND HINGED CLOSURES |
| DIN 28126:1989-04 | DN 125 BOW CLOSURES FOR PROCESS EQUIPMENT |
| DIN 5512-3:2004-05 | MATERIALS FOR RAIL VEHICLES - STEELS - PART 3: STAINLESS STEEL FLAT PRODUCTS - SELECTED STANDARD |
| DIN 25452:1992-04 | MECHANICAL DESIGN OF FUEL ELEMENT STORAGE POOL IN NUCLEAR POWER PLANTS WITH LIGHT-WATER REACTORS |
| DIN 2609:1991-02 | STEEL BUTT-WELDING PIPE FITTINGS - TECHNICAL DELIVERY CONDITIONS |
| DIN 28053:1997-04 | CHEMICAL APPARATUS - ORGANIC COATINGS AND LININGS ON METAL COMPONENTS - REQUIREMENTS FOR METAL SURFACES |
| DIN 2413-1:1993-10 | STEEL PIPES - DESIGN OF STEEL PRESSURE PIPES |
| DIN 4942:1999-01 | THREADED STEEL RISING PIPES FOR RAISING OF WATER - NOMINAL DIAMETER DN 50 TO DN 200 |
| DIN 17441:1997-02 | STAINLESS STEELS - TECHNICAL DELIVERY CONDITIONS FOR COLD ROLLED STRIPS AND SLIT COILS STRIP AND SHEETS CUT FROM SUCH STRIPS FOR PRESSURE PURPOSES |
| DIN 8556-1:1986-05 | FILLER METALS FOR WELDING STAINLESS AND HEAT RESISTANT STEELS; DESIGNATION, TECHNICAL DELIVERY CONDITIONS |
| DIN 50138:1979-05 | TESTING OF METALLIC MATERIALS; RING TENSILE TEST ON TUBES |
| DIN 2413:2011-06 | SEAMLESS STEEL TUBES FOR OIL- AND WATER-HYDRAULIC SYSTEMS - CALCULATION RULES FOR PIPES AND ELBOWS FOR DYNAMIC LOADS |
| DIN 50049:1992-04 | METALLIC PRODUCTS; TYPES OF INSPECTION DOCUMENTS |
| DIN 50145:1975-05 | TESTING OF METALLIC MATERIALS; TENSILE TEST |
| DIN 50104:1983-11 | TESTING OF HOLLOW BODIES BY INTERNAL PRESSURE; LEAK DETECTION UP TO A CERTAIN PRESSURE VALUE; GENERAL SPECIFICATIONS |
| DIN 50135 : 1965 | TESTING OF METALLIC MATERIALS; DRIFT EXPANDING TEST FOR TUBES |
| DIN 50914:1996-09 | TESTING THE RESISTANCE OF STAINLESS STEELS TO INTERGRANULAR CORROSION - METHOD BY USING COPPER SULFATE AND SULFURIC ACID - STRAUSS TEST |
| DIN 50136:1979-06 | TESTING OF METALLIC MATERIALS; FLATTENING TEST ON TUBES |
| DIN 17455:1999-02 | WELDED CIRCULAR STAINLESS STEEL TUBES WITH GENERAL QUALITY REQUIREMENTS - TECHNICAL DELIVERY CONDITIONS |
| DIN 50120-1:1975-09 | TESTING OF STEEL - TENSILE TEST ON FUSION WELDED BUTT JOINTS |
| DIN 40080:1979-04 | SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES |
| DIN 28181:2007-09 | WELDED STEEL TUBES FOR TUBULAR HEAT EXCHANGERS - DIMENSIONS AND MATERIALS |
| DIN 50140:1980-09 | TESTING OF METALLIC MATERIALS; TENSILE TESTING OF TUBES AND TUBE STRIPS |
| DIN 17440:2001-03 | STAINLESS STEELS - TECHNICAL DELIVERY CONDITIONS FOR DRAWN WIRE |
| DIN 50137:1979-06 | TESTING OF STEEL; RING EXPANDING TEST ON TUBES |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.