DIN 18515-1:1998-08
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
CLADDING FOR EXTERNAL WALLS - PART 1: TILES FIXED WITH MORTAR - PRINCIPLES OF DESIGN AND APPLICATION
Hardcopy , PDF
07-03-2021
English
01-01-1998
Foreword
1 Scope and field of application
2 Normative references
3 Concepts
4 Materials
5 Requirements for external walls
6 Claddings fixed to walls without external
thermal insulation
7 Claddings fixed to walls with external
Thermal insulation
Specifies requirements for the installation and design of cladding that comprises tiles or (cast or natural) stone units having a side length no greater than 0,40 m, a thickness no greater than 0,015 m, and an area not exceeding 0,12 m[2] (fluted tiles may be up to 0,02 m thick, including flutes). Also applies to cladding units having a thickness greater than 0,015 m and up to 0,03 m if their mass is not greater than 1,5 kg unit and their bond area is at least 100 cm[2].
DevelopmentNote |
Suspended until publication of a revised English text, due to a new German edition. (05/2015)
|
DocumentType |
Standard
|
Pages |
6
|
PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
Status |
Superseded
|
DIN 18540:2014-09 | SEALING OF EXTERIOR WALL JOINTS IN BUILDING USING JOINT SEALANTS |
DIN 1053-1:1996-11 | MASONRY - PART 1: DESIGN AND CONSTRUCTION |
DIN 17441:1997-02 | STAINLESS STEELS - TECHNICAL DELIVERY CONDITIONS FOR COLD ROLLED STRIPS AND SLIT COILS STRIP AND SHEETS CUT FROM SUCH STRIPS FOR PRESSURE PURPOSES |
DIN 1045 : 1988 AMD 1 1996 | STRUCTURAL USE OF CONCRETE - DESIGN AND CONSTRUCTION |
DIN 4226-1:2001-07 | AGGREGATES FOR CONCRETE AND MORTAR - PART 1: NORMAL AND HEAVY-WEIGHT AGGREGATES |
DIN 18550-2:2015-06 | DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 2: SUPPLEMENTARY PROVISIONS FOR DIN EN 13914-2:2016-09 FOR INTERNAL PLASTERING |
DIN 18516-1:2010-06 | Cladding for external walls, ventilated at rear - Part 1: Requirements, principles of testing |
DIN EN 1322:1999-03 | ADHESIVES FOR TILES - DEFINITIONS AND TERMINOLOGY |
DIN 1053-2:1996-11 | MASONRY - PART 2: MASONRY STRENGTH CLASSES ON THE BASIS OF SUITABILITY TESTS |
DIN 18156-2:1978-03 | MATERIALS FOR CERAMIC LININGS BY THIN MORTAR BED TECHNIQUE - HYDRAULIC MORTAR |
DIN 66133:1993-06 | DETERMINATION OF PORE VOLUME DISTRIBUTION AND SPECIFIC SURFACE AREA OF SOLIDS BY MERCURY INTRUSION |
DIN 18164-1:1992-08 | RIGID CELLULAR PLASTICS INSULATING BUILDING MATERIALS - THERMAL INSULATING MATERIALS |
DIN 18157-1:2016-01 (Draft) | EXECUTION OF TILINGS AND COVERINGS BY THIN MORTAR BED TECHNIQUE - PART 1: CEMENT-BASED MORTARS |
DIN EN 187-1:1991-12 | EXTRUDED CERAMIC TILES WITH A WATER ABSORPTION OF 6% < E = 10% (GROUP A2B) |
DIN EN 187-2:1991-12 | EXTRUDED CERAMIC TILES WITH A WATER ABSORPTION OF 6% < E = 10% (GROUP A2B) |
DIN 18516-3:2013-09 | CLADDING FOR EXTERNAL WALLS, VENTILATED AT REAR - PART 3: NATURAL STONE - REQUIREMENTS, DESIGN |
DIN 105-1:1989-08 | CLAY BRICKS - SOLID BRICKS AND VERTICALLY PERFORATED BRICKS |
DIN 18500:1991-04 | CAST STONES - TERMINOLOGY, REQUIREMENTS, TESTING, INSPECTION |
DIN 1164-1 : 1994 AMD 1 1999 | CEMENT - PART 1: COMPOSITION, SPECIFICATIONS |
DIN 17440:2001-03 | STAINLESS STEELS - TECHNICAL DELIVERY CONDITIONS FOR DRAWN WIRE |
DIN 4108-3:2014-11 | THERMAL PROTECTION AND ENERGY ECONOMY IN BUILDINGS - PART 3: PROTECTION AGAINST MOISTURE SUBJECT TO CLIMATE CONDITIONS - REQUIREMENTS AND DIRECTIONS FOR DESIGN AND CONSTRUCTION |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.