DIN EN 133200 : 2000
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SECTIONAL SPECIFICATION - PASSIVE FILTER UNITS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION (FILTERS, FOR WHICH SAFETY TESTS ARE REQUIRED)
01-05-2006
12-01-2013
1 Allgemeines
1.1 Anwendungsbereich
1.2 Normative Verweisungen
1.3 Angaben in der Bauartspezifikation
1.4 Begriffsbestimmungen
1.5 Kennzeichnung
2 Bevorzugte Bemessungswerte und Eigenschaften
2.1 Bevorzugte Eigenschaften
2.2 Bevorzugte Bemessungswerte
3 Qualitätsbewertungsverfahren
3.1 Primäre Fabrikationsstufe
3.2 Strukturell ähnliche Filter
3.3 Bestätigte Prüfberichte freigegebener Lose
3.4 Anerkennungsprüfungen
3.5 Qualitätskonformitätskontrollen
4 Prüf- und Messverfahren
4.0 Kapazität und Verlustfaktor (tan-[delta]-Messungen)
4.1 Sichtkontrolle und Prüfung der Masse
4.2 Spannungsprüfung
4.3 Isolationswiderstand
4.4 Gleichstromwiderstand oder Spannungsabfall bei
Bemessungsstrom
4.5 Einfügungsdämpfung
4.6 Widerstand
4.7 Mechanische Widerstandsfähigkeit der Anschlüsse
4.8 Lötwärmebeständigkeit
4.9 Lötbarkeit
4.10 Rascher Temperaturwechsel
4.11 Schwingen
4.12 Dauerschocken
4.13 Schocken
4.14 Gehäusedichtheit
4.15 Reihenfolge klimatischer Prüfungen (Klimafolge)
4.16 Feuchte Wärme, konstant
4.17 Temperaturanstieg
4.18 Stossspannung
4.19 Dauerprüfung
4.20 Lade-/Entladeprüfung
4.21 Passive Entflammbarkeit
4.22 Überlaststrom
4.23 Lösemittelbeständigkeit der Kennzeichnung
4.24 Lösemittelbeständigkeit des Bauelementes
Anhang A (normativ) Prüfplan für die Bauartanerkennung
- Qualitätsbewertungsstufe D
Anhang B (normativ) Prüfplan für Sicherheitsprüfungen
Anhang C (normativ) Schaltung für die Stossspannungsprüfung
Anhang D (normativ) Schaltung für die Dauerspannungsprüfung
Anhang E (normativ) Aufbaubeschreibung
Defines passive filter units for electromagnetic interference suppression which fall within the scope of the Generic Specification EN 133000. Specified according to this specification will either be connected to mains supplies, when compliance with the mandatory tests of Table 2 is necessary, or used on other circuit positions where the equipment specification prescribes that some or all of these safety tests are required. Applies to those connected to an a.c. mains or other supply with a nominal voltage not exceeding 1000 V a.c. (r.m.s.) or 1000 V d.c. with a nominal frequency not exceeding 400 Hz.
| DevelopmentNote |
Supersedes DIN 57565-3 and DIN VDE 0565-3. (10/2004)
|
| DocumentType |
Standard
|
| PublisherName |
Verband Deutscher Elektrotechniker
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| I.S. EN 133200:1995 | Identical |
| EN 133200:1999 | Identical |
| BS EN 133200:1999 | Identical |
| SN EN 133200 : 1994 | Identical |
| DIN EN 133201 : 1999 | BLANK DETAIL SPECIFICATION - PASSIVE FILTER UNITS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION - FILTERS FOR WHICH SAFETY TESTS ARE REQUIRED |
| DIN EN 133221 : 1999 | BLANK DETAIL SPECIFICATION - PASSIVE FILTER UNITS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION - FILTERS FOR WHICH SAFETY TESTS ARE REQUIRED (SAFETY TESTS ONLY) |
| DIN 57106-1 : 1982 | PROTECTION AGAINST ELECTRIC SHOCK - CLASSIFICATION OF ELECTRICAL AND ELECTRONIC EQUIPMENT |
| DIN ISO 2859-1:2014-08 | SAMPLING PROCEDURES FOR INSPECTION BY ATTRIBUTES - PART 1: SAMPLING SCHEMES INDEXED BY ACCEPTANCE QUALITY LIMIT (AQL) FOR LOT-BY-LOT INSPECTION (ISO 2859-1:1999 + COR. 1:2001 + AMD.1:2011) |
| DIN EN 133100:1999-03 | SECTIONAL SPECIFICATION: PASSIVE FILTER UNITS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION - FILTERS FOR WHICH SAFETY TESTS ARE NOT REQUIRED |
| DIN IEC 60063:1985-12 | PREFERRED NUMBER SERIES FOR RESISTORS AND CAPACITORS |
| DIN EN 100114-1:1996-11 | RULE OF PROCEDURE - QUALITY ASSESSMENT PROCEDURE - PART 1: CECC REQUIREMENTS FOR THE APPROVAL OF AN ORGANIZATION |
| DIN IEC 60085 : 1993 | THERMAL EVALUATION AND CLASSIFICATION OF ELECTRICAL INSULATION |
| DIN VDE 0106-1 : 1982 | CLASSIFICATION OF ELECTRICAL AND ELECTRONIC EQUIPMENT PROTECTION AGAINST ELECTRIC SHOCK |
| DIN EN 60062:2014-03 (Draft) | MARKING CODES FOR RESISTORS AND CAPACITORS (IEC 60062:2016 + COR1:2016) |
| DIN IEC 60060-1 : 1994 | HIGH VOLTAGE TEST TECHNIQUES - GENERAL SPECIFICATIONS AND TEST REQUIREMENTS |
| DIN IEC 60294:1986-01 | MEASUREMENT OF THE DIMENSIONS OF A CYLINDRICAL COMPONENT HAVING TWO AXIAL TERMINATIONS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.