DIN EN 14782:2015-09 (Draft)

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
  4.1 Materials
  4.2 Nominal thickness
  4.3 Mechanical resistance
       4.3.1 General
       4.3.2 Resistance of roofing products to
             concentrated forces
  4.4 Water permeability
  4.5 Vapour and air permeability
  4.6 Dimensional change
  4.7 Dimensional tolerances
  4.8 Durability
  4.9 External fire performance
  4.10 Reaction to fire
  4.11 Release of regulated dangerous substances
5 Testing, assessment and sampling methods
  5.1 External fire performance for roof covering products
       5.1.1 Products deemed to satisfy the requirements for
             external fire performance
       5.1.2 Products classified without the need for further
             testing (CWFT option)
       5.1.3 Other products
  5.2 Reaction to fire
       5.2.1 Products satisfying the requirements for reaction
             to fire Class A1 without the need for testing
       5.2.2 Products classified without the need for further
             testing (CWFT option)
       5.2.3 Other products
  5.3 Release of regulated dangerous substances
6 Evaluation of conformity
  6.1 General
  6.2 Initial type testing (ITT)
       6.2.1 General
       6.2.2 Sampling for ITT
  6.3 Factory production control (FPC)
       6.3.1 General
       6.3.2 General requirements
7 Designation
8 Product marking
Annex A (normative) Multilayer coated steel sheet
      A.1 General
      A.2 Substrate materials
      A.3 Specific requirements
          A.3.1 Minimum nominal values of thickness
          A.3.2 Bituminous coating specification
          A.3.3 Durability
      A.4 Freedom from defects
Annex B (normative) Determination of resistance to
                    concentrated forces
      B.1 Principle
      B.2 Test spans
      B.3 Test sheets
      B.4 Test procedure
      B.5 Number of tests and analysis of results
      B.6 Acceptance criteria
      B.7 Test report
Annex C (normative) Mounting and fixing conditions of the
                    test specimen for reaction to fire testing
      C.1 General
      C.2 Mounting and fixing conditions
          C.2.1 General
          C.2.2 General configuration
          C.2.3 Securing the overlap vertical joint
          C.2.4 Standard assembly - Steel corner flashings
          C.2.5 Alternative assembly - Corner flashings and seals
          C.2.6 Test arrangement for reaction to fire test
                according to EN ISO 11925-2 (Ignitability test)
      C.3 Direct and extended application of the fire test
          results according to EN 13823
          C.3.1 General
          C.3.2 Direct application: Systems with only one metal
                sheet (single skin system without insulation)
          C.3.3 Direct application: Systems with two (profiled or
                flat) coated metal sheets (or one cassette plus
                one sheet) with an insulation between the two
                sheets (double skin system)
          C.3.4 Extended application: Other insulated systems -
                General methodology
Annex ZA (informative) Clauses of this European Standard
                       addressing the provisions of the EU
                       Construction Products Directive
      ZA.1 Scope and relevant characteristics
      ZA.2 Procedures for the attestation of conformity of
           products
      ZA.3 CE marking and labelling
Bibliography

Describes the terminology, requirements and test methods for factory made self-supporting metal sheets and tiles (for non-structural applications) delivered in the form of manufactured pieces for roofing and wall cladding and lining.