• DIN EN 60252 : 1994

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    CAPACITORS - MOTOR CAPACITORS

    Available format(s): 

    Superseded date:  01-05-2002

    Language(s): 

    Published date:  13-01-2013

    Publisher:  German Institute for Standardisation (Deutsches Institut für Normung)

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Hauptabschnitt 1: Allgemeines
    1.1 Anwendungsbereich und Zweck
    1.2 Normative Verweisungen
    1.3 Begriffe
    1.4 Betriebsbedingungen
    1.5 Vorzugswerte der Grenzabweichungen der Kapazität
    Hauptabschnitt 2: Qualitätsanforderungen und Prüfungen
    2.1 Prüfanforderungen
    2.2 Art der Prüfungen
    2.3 Typprüfungen
    2.4 Stückprüfungen
    2.5 Tangens des Verlustwinkels
    2.6 Sichtprüfung
    2.7 Spannungsprüfung zwischen den Anschlussklemmen
    2.8 Spannungsprüfung zwischen den Anschlussklemmen
         und dem Gehäuse
    2.9 Kapazitätsmessung
    2.10 Prüfung der Masse
    2.11 Mechanische Prüfungen
    2.12 Dichtheitsprüfung
    2.13 Dauerprüfung
    2.14 Prüfung bei feuchter Wärme
    2.15 Selbstheilprüfung
    2.16 Zerstörungsprüfung
    Hauptabschnitt 3: Überlastungen
    3.1 Zulässige Überlastungen
    Hauptabschnitt 4: Sicherheitsanforderungen
    4.1 Kriech- und Luftstrecken
    4.2 Anschlussklemmen und Anschlussleitungen
    4.3 Erdungsanschlüsse
    4.4 Entladeeinrichtungen
    Hauptabschnitt 5: Bemessungswerte
    5.1 Kennzeichnung
    Hauptabschnitt 6: Installations- und Bedienungsanleitung
    6.1 Allgemeines
    6.2 WahlderBemessungsspannung
    6.3 Prüfung der Kondensatortemperatur
    6.4 Prüfung der Ausgleichsvorgänge
    6.5 Ableitstrom
    Anhang A (normativ) Prüfspannung
    Anhang ZA (normativ) Andere in dieser Norm zitierte
              internationale Publikationen mit den
              Verweisungen auf die entsprechenden europäischen
              Publikationen

    Abstract - (Show below) - (Hide below)

    Applies to motor capacitors meant for connection to windings of asynchronous motors supplied from a single-phase system, having a frequency up to 100 Hz, and to capacitors to be connected to a three-phase asynchronous motors so that these motors may be supplied from a single-phase system. Coverage includes definitions, visual examination, check of dimensions, sealing test, endurance test, destruction test, mechanical tests, and tangent of loss angle.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes DIN VDE 0560-8. (10/2004)
    Document Type Standard
    Publisher German Institute for Standardisation (Deutsches Institut für Normung)
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    DIN EN 61642 : 1998 INDUSTRIAL A.C. NETWORKS AFFECTED BY HARMONICS - APPLICATION OF FILTERS AND SHUNT CAPACITORS
    VDE 0560-430 : 1998 INDUSTRIAL A.C. NETWORKS AFFECTED BY HARMONICS - APPLICATION OF FILTERS AND SHUNT CAPACITORS

    Standards Referencing This Book - (Show below) - (Hide below)

    DIN IEC 60068-2-21:1985-08 ELECTRICAL ENGINEERING; BASIC ENVIRONMENTAL TESTING PROCEDURES; TESTS; TEST U: ROBUSTNESS OF TERMINATIONS AND INTEGRAL MOUNTING DEVICES
    DIN IEC 60068-2-1:1985-08 ELECTRICAL ENGINEERING; BASIC ENVIRONMENTAL TESTING PROCEDURES; TESTS; TESTS A: COLD
    DIN IEC 60068-2-3:1986-12 ELECTRICAL ENGINEERING; BASIC ENVIRONMENTAL TESTING PROCEDURES; TESTS; TEST CA: DAMP HEAT, STEADY STATE
    DIN IEC 60068-2-20:1991-04 ELECTRICAL ENGINEERING; BASIC ENVIRONMENTAL TESTING PROCEDURES; TEST T: SOLDERING
    IEC 60068-2-20:2008 Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads
    DIN IEC 60068-2-6:1990-06 ELECTRICAL ENGINEERING; BASIC ENVIRONMENTAL TESTING PROCEDURES; TEST Fc AND GUIDANCE: VIBRATION (SINUSOIDAL)
    IEC 60068-2-21:2006 Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices
    IEC 60068-2-3:1969 Basic environmental testing procedures - Part 2-3: Tests - Test Ca: Damp heat, steady state
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    IEC 60068-2-1:2007 Environmental testing - Part 2-1: Tests - Test A: Cold
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective