DIN EN 60539-2:2011-04
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
DIRECTLY HEATED NEGATIVE TEMPERATURE COEFFICIENT THERMISTORS - PART 2: SECTIONAL SPECIFICATION - SURFACE MOUNT NEGATIVE TEMPERATURE COEFFICIENT THERMISTORS
Hardcopy , PDF
02-12-2020
German
01-01-2011
1 General
1.1 Scope
1.2 Normative references
1.3 Information to be given in a detail specification
1.3.1 Outline drawing and dimensions
1.3.2 Mounting
1.3.3 Ratings and characteristics
1.4 Terminology
2 Preferred ratings and characteristics
2.1 Tolerances on rated zero-power resistance
2.2 Climatic categories
3 Quality assessment procedures
3.1 Primary stage of manufacture
3.2 Structurally similar components
3.3 Qualification approval procedures
3.3.1 The manufacturer shall comply with 3.4 of IEC 60539-1
3.4 Quality conformance inspection
3.4.1 Qualification approval on the basis of the fixed
sample size procedure
3.5 Quality conformance inspection
3.5.1 Formation of inspection lots
3.5.2 Test schedule
3.5.3 Delayed delivery
3.5.4 Assessment level
4 Test and measurement procedures
4.1 Mounting
4.2 Drying and recovery
4.2.1 Drying
4.2.2 Recovery
4.3 Visual examination and check of dimensions
4.3.1 Visual examination
4.3.2 Requirements
4.3.3 Marking
4.3.4 Dimensions
4.4 Electrical tests
4.4.1 Zero-power resistance
4.4.2 B-value or resistance ratio
4.4.3 Resistance/temperature characteristic
4.5 Thermal tests
4.5.1 Dissipation factor (delta)
4.5.2 Thermal time constant by cooling after self-heating (Tau[c])
4.6 Resistance to soldering heat
4.6.1 Initial measurement
4.6.2 Test conditions
4.6.3 Recovery
4.6.4 Final inspection, measurements and requirements
4.7 Solderability
4.7.1 Test conditions
4.7.2 Recovery
4.7.3 Final inspection, measurements and requirements
4.8 Rapid change of temperature
4.9 Thermal shock
4.10 Climatic sequence
4.10.1 Initial measurements
4.10.2 Dry heat
4.10.3 Damp heat (cyclic), first cycle
4.10.4 Cold
4.10.5 Damp heat (cyclic), remaining cycles
4.10.6 Final measurements
4.11 Damp heat, steady state
4.12 Endurance
4.12.1 Endurance at Theta[3] and P[max.]
4.12.2 Endurance at upper category temperature
4.13 Shear (adhesion) test
4.14 Substrate bending test
4.15 Component solvent resistance
4.16 Solvent resistance of marking
Annex A (normative) Guide for the specification and coding of
dimensions of surface mount negative temperature
coefficient thermistors
Annex ZA (normative) Normative references to international
publications with their corresponding European
publications
DevelopmentNote |
Supersedes DIN IEC 60539-2 and DIN IEC 60539-2:DRAFT AMD 1 issue 11-2009. (04/2011) DRAFT 2018 issued in January 2018. (01/2018)
|
DocumentType |
Standard
|
Pages |
22
|
PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
Standards | Relationship |
NF EN 60539-2 : 2005 AMD 1 2011 | Identical |
EN 60539-2:2004/A1:2010 | Identical |
I.S. EN 60539-2:2004 | Identical |
NBN EN 60539-2 : 2005 AMD 1 2010 | Identical |
BS EN 60539-2 : 2004 | Identical |
IEC 60539-2:2003+AMD1:2010 CSV | Identical |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.