DIN EN ISO 11296-4:2011-07
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 4: LINING WITH CURED-IN-PLACE PIPES
Hardcopy , PDF
German, English
01-01-2011
21-09-2018
National foreword
National Annex NA (informative) - Bibliography
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Pipes at the 'M' stage
6 Fittings at the 'M' stage
7 Ancillary components
8 Fitness for purpose of the installed lining
system at the 'I' stage
9 Installation practice
Annex A (informative) - CIPP components and
their functions
Annex B (normative) - Cured-in-place pipes - Modifications
to ISO 178 for flexural testing
Annex C (normative) - Cured-in-place pipes - Test method
or the determination of long-term
flexural modulus under wet conditions
Annex D (normative) - Cured-in-place pipes - Determination
of the creep factor under dry conditions from
a three-point flexural test
Bibliography
This standard is included in DIN Handbook 13-4.
| DevelopmentNote |
Supersedes DIN EN 13566-4. (07/2011) DRAFT 2017 issued in May 2017. (05/2017)
|
| DocumentType |
Standard
|
| Pages |
42
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 11296-4:2009 | Identical |
| EN ISO 11296-4:2011 | Equivalent |
| EN ISO 11296-4:2018 | Identical |
| DIN HDBK 13-4 : 10ED 2015 | ABWASSERTECHNIK 4 - ABWASSERKANAELE, ABWASSERLEITUNGEN - PLANUNG, VERLEGUNG, BETRIEB, SANIERUNG |
| ISO 25780:2011 | Plastics piping systems for pressure and non-pressure water supply, irrigation, drainage or sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin — Pipes with flexible joints intended to be installed using jacking techniques |
| ISO 8773:2006 | Plastics piping systems for non-pressure underground drainage and sewerage — Polypropylene (PP) |
| ISO 7685:1998 | Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Determination of initial specific ring stiffness |
| ISO 10928:2016 | Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Methods for regression analysis and their use |
| ISO 11295:2017 | Classification and information on design and applications of plastics piping systems used for renovation and replacement |
| DIN EN ISO 11295:2016-08 (Draft) | CLASSIFICATION AND INFORMATION ON DESIGN OF PLASTICS PIPING SYSTEMS USED FOR RENOVATION |
| DIN EN ISO 1043-1:2016-09 | PLASTICS - SYMBOLS AND ABBREVIATED TERMS - PART 1: BASIC POLYMERS AND THEIR SPECIAL CHARACTERISTICS (ISO 1043-1:2011 + AMD.1:2016) |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| DIN EN ISO 899-2:2015-06 | Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point loading (ISO 899-2:2003 + Amd.1:2015) (includes Amendment A1:2015) |
| ISO 11296-1:2009 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 1: General |
| ISO 3126:2005 | Plastics piping systems — Plastics components — Determination of dimensions |
| ISO 13002:1998 | Carbon fibre — Designation system for filament yarns |
| DIN EN ISO 11296-1:2011-07 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 1: GENERAL |
| ISO 8513:2016 | Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test methods for the determination of the initial longitudinal tensile strength |
| ISO 899-2:2003 | Plastics — Determination of creep behaviour — Part 2: Flexural creep by three-point loading |
| ISO 7684:1997 | Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the creep factor under dry conditions |
| ISO 4435:2003 | Plastics piping systems for non-pressure underground drainage and sewerage — Unplasticized poly(vinyl chloride) (PVC-U) |
| EN 14364:2013 | Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints |
| ISO 10952:2014 | Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Determination of the resistance to chemical attack for the inside of a section in a deflected condition |
| ISO 178:2010 | Plastics — Determination of flexural properties |
| ISO 1043-1:2011 | Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics |
| DIN EN ISO 13002:1999-01 | |
| DIN EN ISO 75-2:2013-08 | PLASTICS - DETERMINATION OF TEMPERATURE OF DEFLECTION UNDER LOAD - PART 2: PLASTICS AND EBONITE (ISO 75-2:2013) |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.