Skip to content
Please enter a keyword to search

  • DIN EN ISO 14577-4:2015-05 (Draft)

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    METALLIC MATERIALS - INSTRUMENTED INDENTATION TEST FOR HARDNESS AND MATERIALS PARAMETERS - PART 4: TEST METHOD FOR METALLIC AND NON-METALLIC COATINGS (ISO 14577-4:2016)

    Available format(s):  Hardcopy, PDF

    Superseded date:  07-03-2021

    Language(s):  German

    Published date:  01-01-2015

    Publisher:  German Institute for Standardisation (Deutsches Institut für Normung)

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National foreword
    National Annex NA (informative) - Bibliography
    European foreword
    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Symbols and designations
    4 Calibration and direct verification of testing
      machines
    5 Test pieces
    6 Procedure
    7 Data analysis and evaluation of results for
      indentation normal to the surface
    8 Uncertainty of the results
    9 Test report
    Annex A (informative) - Contact point and fully
            elastic regime
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes a method for testing coatings which is particularly suitable for testing in the nano/micro range applicable to thin coatings.

    General Product Information - (Show below) - (Hide below)

    Comment Closes On
    Document Type Draft
    Publisher German Institute for Standardisation (Deutsches Institut für Normung)
    Status Superseded

    Standards Referenced By This Book - (Show below) - (Hide below)

    DIN EN ISO 14577-3:2015-11 METALLIC MATERIALS - INSTRUMENTED INDENTATION TEST FOR HARDNESS AND MATERIALS PARAMETERS - PART 3: CALIBRATION OF REFERENCE BLOCKS (ISO 14577-3:2015)
    DIN HDBK 478 : 1ED 2015 HAERTE UND VERSCHLEISSFESTIGKEIT VON BESCHICHTUNGEN - PRUEFVERFAHREN
    DIN EN ISO 14577-2:2015-11 METALLIC MATERIALS - INSTRUMENTED INDENTATION TEST FOR HARDNESS AND MATERIALS PARAMETERS - PART 2: VERIFICATION AND CALIBRATION OF TESTING MACHINES (ISO 14577-2:2015)
    DIN EN ISO 14577-1:2015-11 Metallic materials - Instrumented indentation test for hardness and materials parameters - Part 1: Test method (ISO 14577-1:2015); German version EN ISO 14577-1:2015
    VDI/VDE 2616 Blatt 1:2012-08 Hardness testing of metallic materials
    DIN 51200:2016-08 MATERIALS TESTING MACHINES - DESIGN AND APPLICATION OF HOLDING DEVICES FOR TEST PIECES IN HARDNESS TESTING MACHINES

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 1514:2016 Paints and varnishes — Standard panels for testing
    ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories
    ISO 4287:1997 Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters
    ISO 4516:2002 Metallic and other inorganic coatings — Vickers and Knoop microhardness tests
    ISO 2808:2007 Paints and varnishes Determination of film thickness
    DIN EN 23270:1991-09 PAINTS, VARNISHES AND THEIR RAW MATERIALS; TEMPERATURES AND HUMIDITIES FOR CONDITIONING AND TESTING
    ISO 14577-1:2015 Metallic materials Instrumented indentation test for hardness and materials parameters Part 1: Test method
    DIN EN ISO 14577-1:2015-11 Metallic materials - Instrumented indentation test for hardness and materials parameters - Part 1: Test method (ISO 14577-1:2015); German version EN ISO 14577-1:2015
    DIN EN ISO 14577-3:2015-11 METALLIC MATERIALS - INSTRUMENTED INDENTATION TEST FOR HARDNESS AND MATERIALS PARAMETERS - PART 3: CALIBRATION OF REFERENCE BLOCKS (ISO 14577-3:2015)
    ISO 14577-3:2015 Metallic materials Instrumented indentation test for hardness and materials parameters Part 3: Calibration of reference blocks
    DIN EN ISO 1514:2005-02 PAINTS AND VARNISHES - STANDARD PANELS FOR TESTING (ISO 1514:2016)
    ISO 3270:1984 Paints and varnishes and their raw materials — Temperatures and humidities for conditioning and testing
    ISO 14577-2:2015 Metallic materials Instrumented indentation test for hardness and materials parameters Part 2: Verification and calibration of testing machines
    DIN EN ISO 14577-2:2015-11 METALLIC MATERIALS - INSTRUMENTED INDENTATION TEST FOR HARDNESS AND MATERIALS PARAMETERS - PART 2: VERIFICATION AND CALIBRATION OF TESTING MACHINES (ISO 14577-2:2015)
    ISO/IEC Guide 98-3:2008 Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995)
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective