DIN EN ISO 14663-2:2006-06
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
PLASTICS - ETHYLENE/VINYL ALCOHOL (EVOH) COPOLYMER MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
Hardcopy , PDF
English
01-01-2006
07-03-2021
Foreword
1 Scope
2 Normative references
3 Preparation of test specimens
4 Conditioning of test specimens
5 Determination of properties
Annex A (normative) Determination of volatile matter
(including water)
Annex B (normative) Determination of ethylene content
Annex C (normative) Determination of steady-state rate
of transmission of oxygen gas through
ethylene/vinyl alcohol copolymer in the form of
film using a coulometric sensor
Specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of EVOH moulding and extrusion materials.
| DocumentType |
Standard
|
| Pages |
20
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| Standards | Relationship |
| NEN EN ISO 14663-2 : 2006 | Identical |
| ISO 14663-2:1999 | Identical |
| NS EN ISO 14663-2 : 1ED 2006 | Identical |
| BS EN ISO 14663-2:2006 | Identical |
| NF EN ISO 14663-2 : 2006 | Identical |
| I.S. EN ISO 14663-2:2006 | Identical |
| NBN EN ISO 14663-2 : 2006 | Identical |
| EN ISO 14663-2:2006 | Identical |
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| ISO 75-1:2013 | Plastics — Determination of temperature of deflection under load — Part 1: General test method |
| ISO 3451-1:2008 | Plastics — Determination of ash — Part 1: General methods |
| ISO 3167:2014 | Plastics — Multipurpose test specimens |
| IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
| ISO 14663-1:1999 | Plastics — Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials — Part 1: Designation system and basis for specifications |
| ISO 10350:1993 | Plastics — Acquisition and presentation of comparable single-point data |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 2039-2:1987 | Plastics — Determination of hardness — Part 2: Rockwell hardness |
| ISO 1183:1987 | Plastics — Methods for determining the density and relative density of non-cellular plastics |
| IEC 60296:2012 RLV | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| IEC 60093:1980 | Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials |
| ISO 180:2000 | Plastics — Determination of Izod impact strength |
| ISO 294-2:1996 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 2: Small tensile bars |
| ISO 3146:2000 | Plastics — Determination of melting behaviour (melting temperature or melting range) of semi-crystalline polymers by capillary tube and polarizing-microscope methods |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| ISO 291:2008 | Plastics — Standard atmospheres for conditioning and testing |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| ISO 306:2013 | Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST) |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
| ISO 178:2010 | Plastics — Determination of flexural properties |
| ISO 1133:2005 | Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| ISO 527-1:2012 | Plastics — Determination of tensile properties — Part 1: General principles |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.