DIN EN ISO 527-2:2012-06
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012)
Available format(s)
Hardcopy , PDF
Language(s)
English, German
Published date
01-06-2012
Superseded date
01-09-2025
Superseded by
€93.83
Excluding VAT
| DevelopmentNote |
Together with DIN EN ISO 527-1 E supersedes DIN 53455 E. (11/1999) Supersedes DIN 53457 E (08/2002)
|
| DocumentType |
Standard
|
| Pages |
18
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| BS EN ISO 527-2:1996 | Identical |
| NS EN ISO 527-2 : 2012 | Identical |
| NF EN ISO 527-2 : 2012 | Identical |
| I.S. EN ISO 527-2:2012 | Identical |
| EN ISO 527-2:2012 | Identical |
| NEN EN ISO 527-2 : 2012 | Identical |
| ISO 527-2:2012 | Identical |
| NBN EN ISO 527-2 : 2012 | Identical |
| ONORM EN ISO 527-2 : 2012 | Identical |
| DIN EN ISO 11833-1:2012-11 | PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS - PART 1: SHEETS OF THICKNESS NOT LESS THAN 1 MM (ISO 11833-1:2012) |
| DIN EN ISO 80369-7:2017-10 | Small-bore connectors for liquids and gases in healthcare applications - Part 7: Connectors for intravascular or hypodermic applications (ISO 80369-7:2016, Corrected version 2016-12-01) |
| DIN EN ISO 11296-7:2013-05 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 7: LINING WITH SPIRALLY-WOUND PIPES (ISO 11296-7:2011) |
| DIN ISO 23013:2017-10 | ROAD VEHICLES - DETERMINATION OF RESISTANCE TO FORCED ENTRY OF SECURITY GLASS CONSTRUCTIONS USED IN VEHICLE GLAZING - TEST OF GLAZING SYSTEMS (ISO 23013:2016) |
| DIN EN ISO 14910-2:2013-06 | PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 14910-2:2013) |
| DIN EN ISO 15013:2008-01 | Plastics - Extruded sheets of polypropylene (PP) - Requirements and test methods (ISO 15013:2007); German version EN ISO 15013:2007 |
| DIN ISO 11040-4:2017-07 | Prefilled syringes - Part 4: Glass barrels for injectables and sterilized subassembled syringes ready for filling (ISO 11040-4:2015) |
| DIN EN ISO 3672-2:2002-07 | PLASTICS - UNSATURATED-POLYESTER RESINS (UP-R) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN ISO 11439:2013-09 | Gas cylinders - High pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles (ISO 11439:2013) |
| DIN EN 12864 E : 2006 AMD 3 2010 | LOW PRESSURE, NON ADJUSTABLE REGULATORS HAVING A MAXIMUM OUTLET PRESSURE OF LESS THAN OR EQUAL TO 200 MBAR, WITH A CAPACITY OF LESS THAN OR EQUAL TO 4 KG/H, AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES |
| DIN EN ISO 11963:2013-03 | PLASTICS - POLYCARBONATE SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS (ISO 11963:2012) |
| DIN EN 10288:2003-12 | STEEL TUBES AND FITTINGS FOR ONSHORE AND OFFSHORE PIPELINES - EXTERNAL TWO-LAYER EXTRUDED POLYETHYLENE BASED COATINGS |
| DIN ISO 9523:2016-05 | TOURING SKI-BOOTS FOR ADULTS - INTERFACE WITH TOURING SKI-BINDINGS - REQUIREMENTS AND TEST METHODS (ISO 9523:2015) |
| DIN 30678:2013-09 | Polypropylene coatings on steel pipes and fittings - Requirements and testing |
| DIN EN ISO 12215-5:2014-10 | SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 5: DESIGN PRESSURES FOR MONOHULLS, DESIGN STRESSES, SCANTLINGS DETERMINATION (ISO 12215-5:2008 + AMD 1:2014) |
| DIN EN ISO 6224:2012-02 | Thermoplastics hoses, textile-reinforced, for general-purpose water applications - Specification (ISO 6224:2011) |
| DIN ISO 7148-2:2001-03 | PLAIN BEARINGS - TESTING OF THE TRIBOLOGICAL BEHAVIOUR OF BEARING MATERIALS - PART 2: TESTING OF POLYMER-BASED PLAIN BEARING MATERIALS (ISO 7148-2:2012) |
| ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
| ISO 3167:2014 | Plastics — Multipurpose test specimens |
| DIN ISO 5725-2:2002-12 | Accuracy (trueness and precision) of measurement methods and results - Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method (ISO 5725-2:1994 including Technical Corrigendum 1:2002) |
| ISO 11403-3:2014 | Plastics — Acquisition and presentation of comparable multipoint data — Part 3: Environmental influences on properties |
| ISO 294-3:2002 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates |
| DIN EN ISO 2818:1997-06 | PLASTICS - PREPARATION OF TEST SPECIMENS BY MACHINING |
| ISO 295:2004 | Plastics — Compression moulding of test specimens of thermosetting materials |
| ISO 10724-1:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens |
| ISO 1926:2009 | Rigid cellular plastics — Determination of tensile properties |
| ISO 294-2:1996 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 2: Small tensile bars |
| ISO 5725-2:1994 | Accuracy (trueness and precision) of measurement methods and results — Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method |
| ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| DIN EN ISO 527-1:2012-06 | PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 1: GENERAL PRINCIPLES (ISO 527-1:2012) |
| ISO 20753:2008 | Plastics — Test specimens |
| ISO 527-1:2012 | Plastics — Determination of tensile properties — Part 1: General principles |
Summarise
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.