DIN EN ISO 6185-3:2014-12
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
INFLATABLE BOATS - PART 3: BOATS WITH A HULL LENGTH LESS THAN 8 M WITH A MOTOR POWER RATING OF 15 KW AND GREATER (ISO 6185-3:2014)
Available format(s)
Hardcopy , PDF
Superseded date
03-06-2019
Superseded by
Language(s)
English, German
Published date
01-01-2014
Important note : Users cannot be edited or removed once added to your Multi user PDF.
National foreword
National Annex NA (informative) - Bibliography
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Structural Materials
6 Functional components
7 Safety requirements of the completed boat
8 Performance
9 Builder's plate(s)
10 Owner's manual
11 Standard equipment
Annex A (informative) - General arrangement
of a typical Type VII boat
Annex B (informative) - General arrangement
of a typical Type VIlI boat
Annex ZA (informative) - Relationship between
this European Standard and the Essential
Requirements of EU Directive 94/25/EC
as amended by Directive 2003/44/EC
Bibliography
Defines the minimum safety characteristics required for the design, materials to use, manufacture and testing of inflatable boats and rigid inflatable boats with a hull length L[H] in accordance with ISO 8666 less than 8 m with a motor power rating of 15 kW and greater.
| DocumentType |
Standard
|
| Pages |
44
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NBN EN ISO 6185-3 : 2014 | Identical |
| BS EN ISO 6185-3:2014 | Identical |
| I.S. EN ISO 6185-3:2014 | Identical |
| ISO 6185-3:2014 | Identical |
| NS EN ISO 6185-3 : 2014 | Identical |
| SN EN ISO 6185-3 : 2015 | Identical |
| NEN EN ISO 6185-3 : 2014 | Identical |
| UNE-EN ISO 6185-3:2015 | Identical |
| UNI EN ISO 6185-3 : 2014 | Identical |
| NF EN ISO 6185-3 : 2014 | Identical |
| ONORM EN ISO 6185-3 : 2014 | Identical |
| EN ISO 6185-3:2014 | Identical |
| BWB TL 1940-0012 : 5ED 2007 | |
| DIN EN ISO 6185-4:2011-10 | INFLATABLE BOATS - PART 4: BOATS WITH A HULL LENGTH OF BETWEEN 8 M AND 24 M WITH A MOTOR POWER RATING OF 15 KW AND GREATER |
| ISO 10239:2014 | Small craft Liquefied petroleum gas (LPG) systems |
| ISO 15083:2003 | Small craft - Bilge-pumping systems |
| ISO 12215-5:2008 | Small craft Hull construction and scantlings Part 5: Design pressures for monohulls, design stresses, scantlings determination |
| ISO 2896:2001 | Rigid cellular plastics Determination of water absorption |
| ISO 11192:2005 | Small craft Graphical symbols |
| ISO 7010:2011 | Graphical symbols Safety colours and safety signs Registered safety signs |
| ISO 14946:2001 | Small craft Maximum load capacity |
| DIN EN ISO 6185-4:2011-10 | INFLATABLE BOATS - PART 4: BOATS WITH A HULL LENGTH OF BETWEEN 8 M AND 24 M WITH A MOTOR POWER RATING OF 15 KW AND GREATER |
| DIN ISO 3864-1:2012-06 | Graphical symbols - Safety colours and safety signs - Part 1: Design principles for safety signs and safety markings (ISO 3864-1:2011) |
| DIN EN ISO 2411:2016-07 (Draft) | RUBBER OR PLASTICS-COATED FABRICS - DETERMINATION OF COATING ADHESION (ISO 2411:2017) |
| ISO 4675:2017 | Rubber- or plastics-coated fabrics — Low-temperature bend test |
| DIN EN ISO 15085:2009-10 | SMALL CRAFT - MAN-OVERBOARD PREVENTION AND RECOVERY |
| ISO 12217-3:2015 | Small craft — Stability and buoyancy assessment and categorization — Part 3: Boats of hull length less than 6 m |
| ISO 10088:2013 | Small craft — Permanently installed fuel systems |
| ISO 11547:1994 | Small craft — Start-in-gear protection |
| DIN EN ISO 11105:1997-07 | SMALL CRAFT - VENTILATION OF PETROL ENGINE AND/OR PETROL TANK COMPARTMENTS |
| ISO 6185-4:2011 | Inflatable boats Part 4: Boats with a hull length of between 8 m and 24 m with a motor power rating of 15 kW and greater |
| DIN EN ISO 16180:2013-07 | SMALL CRAFT - NAVIGATION LIGHTS - INSTALLATION, PLACEMENT AND VISIBILITY (ISO 16180:2013) |
| ISO 2411:2017 | Rubber- or plastics-coated fabrics — Determination of coating adhesion |
| ISO 11105:1997 | Small craft Ventilation of petrol engine and/or petrol tank compartments |
| ISO 11592:2001 | Small craft less than 8 m length of hull Determination of maximum propulsion power rating |
| ISO 8666:2016 | Small craft Principal data |
| DIN EN ISO 10592:1995-06 | Small craft - Hydraulic steering systems (ISO 10592:1994) |
| DIN EN ISO 12216:2002-10 | SMALL CRAFT - WINDOWS, PORTLIGHTS, HATCHES, DEADLIGHTS AND DOORS - STRENGTH AND WATERTIGHTNESS REQUIREMENTS |
| DIN ISO 1817:2016-11 | RUBBER, VULCANIZED OR THERMOPLASTIC - DETERMINATION OF THE EFFECT OF LIQUIDS (ISO 1817:2015) |
| DIN EN ISO 21487:2016-05 | SMALL CRAFT - PERMANENTLY INSTALLED PETROL AND DIESEL FUEL TANKS (ISO 21487:2012 + AMD 1:2014 + AMD 2:2015) |
| ISO 8847:2004 | Small craft Steering gear Cable and pulley systems |
| DIN EN ISO 10240:2015-09 | SMALL CRAFT - OWNER'S MANUAL (ISO 10240:2004 + AMD 1:2015) |
| ISO 15084:2003 | Small craft Anchoring, mooring and towing Strong points |
| ISO 9775:1990 | Small craft Remote steering systems for single outboard motors of 15 kW to 40 kW power |
| ISO 10133:2012 | Small craft Electrical systems Extra-low-voltage d.c. installations |
| ISO 8469:2013 | Small craft Non-fire-resistant fuel hoses |
| ISO 12217-1:2015 | Small craft — Stability and buoyancy assessment and categorization — Part 1: Non-sailing boats of hull length greater than or equal to 6 m |
| ISO 12215-3:2002 | Small craft — Hull construction and scantlings — Part 3: Materials: Steel, aluminium alloys, wood, other materials |
| DIN EN ISO 10088:2013-12 | Small craft - Permanently installed fuel systems (ISO 10088:2013) |
| DIN EN ISO 11812:2003-07 | SMALL CRAFT - WATERTIGHT COCKPITS AND QUICK-DRAINING COCKPITS |
| ISO 8846:1990 | Small craft — Electrical devices — Protection against ignition of surrounding flammable gases |
| ISO 8849:2003 | Small craft Electrically operated direct-current bilge pumps |
| ISO 8848:1990 | Small craft Remote steering systems |
| DIN EN ISO 10239:2015-05 | SMALL CRAFT - LIQUEFIED PETROLEUM GAS (LPG) SYSTEMS (ISO 10239:2014) |
| ISO 16180:2013 | Small craft — Navigation lights — Installation, placement and visibility |
| ISO 10592:1994 | Small craft Hydraulic steering systems |
| ISO 15652:2003 | Small craft Remote steering systems for inboard mini jet boats |
| ISO 11812:2001 | Small craft Watertight cockpits and quick-draining cockpits |
| DIN EN ISO 8099:2015-11 (Draft) | SMALL CRAFT - TOILET WASTE RETENTION SYSTEMS |
| ISO 12215-1:2000 | Small craft — Hull construction and scantlings — Part 1: Materials: Thermosetting resins, glass-fibre reinforcement, reference laminate |
| ISO 10240:2004 | Small craft Owner's manual |
| ISO 21487:2012 | Small craft — Permanently installed petrol and diesel fuel tanks |
| ISO 3864-1:2011 | Graphical symbols Safety colours and safety signs Part 1: Design principles for safety signs and safety markings |
| ISO 13297:2014 | Small craft Electrical systems Alternating current installations |
| ISO 15085:2003 | Small craft — Man-overboard prevention and recovery |
| ISO 9094:2015 | Small craft — Fire protection |
| EN 314-2:1993 | Plywood - Bonding quality - Part 2: Requirements |
| DIN EN ISO 9094:2016-05 | Small craft - Fire protection (ISO 9094:2015) |
| DIN EN 29775:1993-10 | Small craft; remote steering systems for single outboard motors of 15 kW to 40 kW (ISO 9975:1990); German version EN 29975:1993 |
| ISO 16147:2002 | Small craft Inboard diesel engines Engine-mounted fuel and electrical components |
| ISO 15584:2001 | Small craft Inboard petrol engines Engine-mounted fuel and electrical components |
| DIN EN ISO 4674-1:2015-04 (Draft) | RUBBER- OR PLASTICS-COATED FABRICS - DETERMINATION OF TEAR RESISTANCE - PART 1: CONSTANT RATE OF TEAR METHODS (ISO 4674-1:2016) |
| DIN EN ISO 8666:2014-12 (Draft) | SMALL CRAFT - PRINCIPAL DATA (ISO 8666:2016) |
| ISO 8665:2006 | Small craft Marine propulsion reciprocating internal combustion engines Power measurements and declarations |
| ISO 12216:2002 | Small craft Windows, portlights, hatches, deadlights and doors Strength and watertightness requirements |
| DIN EN ISO 12217-3:2016-03 | SMALL CRAFT - STABILITY AND BUOYANCY ASSESSMENT AND CATEGORIZATION - PART 3: BOATS OF HULL LENGTH LESS THAN 6 M (ISO 12217-3:2015) |
| DIN EN ISO 7010:2012-10 | GRAPHISCHE SYMBOLE - SICHERHEITSFARBEN UND SICHERHEITSZEICHEN - REGISTRIERTE SICHERHEITSZEICHEN (ISO 7010:2011/AMD 5:2014) |
| DIN EN ISO 13297:2015-04 | SMALL CRAFT - ELECTRICAL SYSTEMS - ALTERNATING CURRENT INSTALLATIONS (ISO 13297:2014) |
| ISO 3011:1997 | Rubber- or plastics-coated fabrics Determination of resistance to ozone cracking under static conditions |
| DIN EN ISO 10133:2013-04 | Small craft - Electrical systems - Extra-low-voltage d.c. installations (ISO 10133:2012) |
| ISO 4674-1:2016 | Rubber- or plastics-coated fabrics Determination of tear resistance Part 1: Constant rate of tear methods |
| ISO 10087:2006 | Small craft Craft identification Coding system |
| ISO 12215-6:2008 | Small craft — Hull construction and scantlings — Part 6: Structural arrangements and details |
| DIN EN ISO 12215-3:2002-09 | SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 3: MATERIALS: STEEL, ALUMINIUM ALLOYS, WOOD, OTHER MATERIALS |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
| ISO 14945:2004 | Small craft Builder's plate |
| ISO 8099:2000 | Small craft Toilet waste retention systems |
| DIN EN ISO 12217-1:2016-08 | SMALL CRAFT - STABILITY AND BUOYANCY ASSESSMENT AND CATEGORIZATION - PART 1: NON-SAILING BOATS OF HULL LENGTH GREATER THAN OR EQUAL TO 6 M (ISO 12217-1:2015) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.