EN 14035-21:2005

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Construction
  4.1 Means of ignition
  4.2 Attachment of initial fuse
  4.3 Protection of initial fuse
      4.3.1 General
      4.3.2 Initial fuse protected by fuse cover
      4.3.3 Initial fuse protected by primary pack
            or selection pack
      4.3.4 Initial fuse designed to resist side
            ignition
  4.4 Materials of firework case
  4.5 Integrity
  4.6 Net explosive content
  4.7 Visibility of fuse
5 Performance
  5.1 Initial fuse
  5.2 Principal effects
  5.3 Functioning
  5.4 Explosions
  5.5 Motion of the jumping ground spinner
  5.6 Burning matter
  5.7 Projected debris
6 Primary pack or selection pack
7 Minimum labelling requirements
  7.1 General
  7.2 Type name and category
  7.3 Safety information
      7.3.1 General
      7.3.2 Jumping ground spinners
      7.3.3 Identification of top side
  7.4 Name, address and telephone number of
      manufacturer or distributor or importer
  7.5 Reference to this document
  7.6 Printing
      7.6.1 Labelling
      7.6.2 Type size
  7.7 Marking of very small jumping ground spinners
      7.7.1 Reduced size
      7.7.2 Reduced information
  7.8 Additional information on the primary pack
      (if applicable)
8 Test methods
  8.1 Attachment of initial fuse (type test and
      batch test)
      8.1.1 Apparatus
      8.1.2 Procedure
  8.2 Performance (type test and batch test)
      8.2.1 Test environment
      8.2.2 Apparatus
      8.2.3 Procedure
  8.3 Determination of net explosive content (type
      test)
      8.3.1 Apparatus
      8.3.2 Procedure
  8.4 Side ignition of initial fuse (type test)
      8.4.1 Material
      8.4.2 Test area
      8.4.3 Apparatus
      8.4.4 Test specimen
      8.4.5 Procedure
  8.5 Labelling (type test and batch test)
Annex A (normative) Type testing
Annex B (normative) Batch testing
Annex C (normative) Method for determination of
                      smouldering rate of cigarette
Annex D (informative) A-Deviations

This European Standard specifies requirements for the construction, performance, primary packaging and labelling of jumping ground spinners and the corresponding test methods. It is applicable to fireworks which are classified as jumping ground spinners of category 2 in EN 14035-2.It is not applicable to jumping ground spinners containing any report charge.It is not applicable to jumping ground spinners containing pyrotechnic composition that includes any of the following substances:-arsenic or arsenic compounds;-mixtures containing a mass fraction of chlorates greater than 80 percent;-mixtures of chlorates with metals;-mixtures of chlorates with red phosphorus;-mixtures of chlorates with potassium hexacyanoferrate(II);-mixtures of chlorates with sulfur;-mixtures of chlorates with sulfides;-lead or lead compounds;-mercury compounds;-white phosphorus;-picrates or picric acid;-potassium chlorate with a mass fraction of bromates greater than 0,15 percent;-sulfur with an acidity, expressed as mass fraction of sulfuric acid, greater than 0,002 percent;-zirconium with a particle size of less than 40 mm.NOTEIn EN 14035-2, jumping ground spinners are classified as follows:- brief description: non-metallic tubes containing gas- and sparks-producing pyrotechnic composition, with or without an aural pyrotechnic composition;- principal effects: rotation on the ground frequently interrupted by a jumping motion and emission of sparks and flames with or without whistling effect.Schemes for type testing of jumping ground spinners and batch testing of jumping ground spinners are specified in Annex A and Annex B respectively.