EN 14764:2005
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
City and trekking bicycles - Safety requirements and test methods
05-11-2021
EN ISO 4210-3:2014
EN ISO 4210-5:2014
EN ISO 4210-8:2014
EN ISO 4210-4:2014
EN ISO 4210-7:2014
EN ISO 4210-9:2014
EN ISO 4210-6:2015
EN ISO 4210-1:2014
EN ISO 4210-2:2015
EN ISO 4210-4 : 2014 COR 2014
07-12-2005
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements and test methods
4.1 Brake tests and strength tests - Special
requirements
4.1.1 Definition of brake tests
4.1.2 Definition of strength tests
4.1.3 Numbers and condition of specimens for
the strength tests
4.1.4 Accuracy tolerances of test conditions for
brake tests and strength tests
4.2 Sharp edges
4.3 Security and strength of safety-related fasteners
4.3.1 Security of screws
4.3.2 Minimum failure torque
4.3.3 Folding bicycles
4.4 Crack detection methods
4.5 Protrusions
4.5.1 Requirement
4.5.2 Test method
4.6 Brakes
4.6.1 Braking-systems
4.6.2 Hand-operated brakes
4.6.3 Attachment of brake assembly and cable
requirements
4.6.4 Brake-block and brake-pad assemblies - Security test
4.6.5 Brake adjustment
4.6.6 Hand-operated braking-system - Strength test
4.6.7 Back-pedal braking system
4.6.8 Braking performance
4.6.9 Brakes - Heat-resistance test
4.7 Steering
4.7.1 Handlebar - Dimensions
4.7.2 Handlebar grips and plugs
4.7.3 Handlebar stem - Insertion-depth mark or
positive stop
4.7.4 Handlebar stem-extension to fork-stem -
Clamping requirements
4.7.5 Steering stability
4.7.6 Steering assembly - Static strength and security
tests
4.7.7 Handlebar and stem assembly - Fatigue test
4.8 Frames
4.8.1 Suspension-frames - Special requirements
4.8.2 Frame and front-fork assembly - Impact
test (falling mass)
4.8.3 Frame - Fatigue test with pedalling forces
4.8.4 Frame - Fatigue test with a vertical force
4.9 Front fork
4.9.1 General
4.9.2 Means of location of the axle and wheel retention
4.9.3 Suspension-forks - Special requirements
4.9.4 Front fork - Static bending test
4.9.5 Front fork - Rearward impact test
4.9.6 Front fork - Bending fatigue test
4.9.7 Forks intended for use with hub- or disc-brakes
4.10 Wheels and wheel/tyre assembly
4.10.1 Rotational accuracy
4.10.2 Wheel/tyre assembly - Clearance
4.10.3 Wheels - Static strength test
4.10.4 Wheels - Wheel retention
4.10.5 Wheels - Quick-release devices
4.11 Rims, tyres and tubes
4.11.1 Tyre inflation pressure
4.11.2 Tyre and rim compatibility
4.11.3 Rim-wear
4.12 Mudguards
4.12.1 Requirement
4.12.2 Stage 1: Test method - Tangential obstruction
4.12.3 Stage 2: Test method - Radial force
4.13 Pedals and pedal/crank drive system
4.13.1 Pedal tread
4.13.2 Pedal clearance
4.13.3 Pedal/pedal-spindle assembly - Static strength test
4.13.4 Pedal-spindle - Impact test
4.13.5 Pedal/pedal-spindle - Dynamic durability test
4.13.6 Drive-system - Static strength test
4.13.7 Crank assembly - Fatigue test
4.14 Saddles and seat-pillar
4.14.1 General
4.14.2 Limiting dimensions
4.14.3 Seat-pillar - Insertion-depth mark or positive stop
4.14.4 Saddle/seat pillar
4.14.5 Saddle - Static strength test
4.14.6 Saddle and seat-pillar clamp - Fatigue test
4.14.7 Seat-pillar - Fatigue test
4.15 Drive-chain
4.16 Chainguard
4.16.1 Requirement
4.16.2 Chain-wheel disc diameter
4.16.3 Chain protective de
4.16.4 Combined front gear-change guide
4.17 Spoke protector
4.18 Luggage carriers
4.19 Handling and operation of a fully-assembled bicycle
4.19.1 Requirement
4.19.2 Test method
4.20 Lighting systems and reflectors
4.20.1 Lighting and reflectors
4.20.2 Wiring harness
4.21 Warning device
5 Manufacturer's instructions
6 Marking
6.1 Requirement
6.2 Durability test
6.2.1 Requirement
6.2.2 Test method
Annex A (informative) Explanation of the method of least
squares for obtaining line of best
fit and +/-20 % limit lines for
braking performance linearity
Annex B (informative) Steering geometry
Annex C (informative) Structural integrity of the fully
assembled bicycle
Annex D (informative) Wheel/tyre assembly - Fatigue test
Bibliography
This European Standard specifies safety and performance requirements for the design, assembly, and testing of bicycles and sub-assemblies intended for use on public roads, and lays down guide lines for instructions on the use and care of such bicycles.This European Standard applies to bicycles that have a maximum saddle height of 635 mm or more and that are in-tended for use on public roads.This standard does not apply to mountain bicycles and racing bicycles, tradesman's delivery bicycles, recumbent bicycles, tandems and bicycles designed and equipped for use in sanctioned competitive events.NOTE For bicycles with a maximum saddle height of 435 mm see EN 71 and with a maximum saddle height of more than 435 mm and less than 635 mm see EN 14765.
Committee |
CEN/TC 333
|
DocumentType |
Standard
|
PublisherName |
Comite Europeen de Normalisation
|
Status |
Superseded
|
SupersededBy |
Standards | Relationship |
DIN EN 14764 E : 2006 | Identical |
UNE-EN 14764:2006 | Identical |
I.S. EN 14764:2006 | Identical |
SN EN 14764 : 2006 | Identical |
PN EN 14764 : 2007 | Identical |
NBN EN 14764 : 2006 | Identical |
UNI EN 14764 : 2006 | Identical |
NS EN 14764 : 1ED 2006 | Identical |
NEN EN 14764 : 2006 | Identical |
NF EN 14764 : 2006 | Identical |
UNE-EN 15764:2010 | Identical |
BS EN 14764:2005 | Identical |
DIN EN 14764:2006-03 | Identical |
BS EN 15918 : 2011 | CYCLES - CYCLE TRAILER - SAFETY REQUIREMENTS AND TEST METHODS |
S.R. CEN TR 16041:2010 | BICYCLES - REPLIES TO REQUESTS FOR INTERPRETATION OF EN 14764 |
S.R. CEN TR 16043:2010 | BICYCLES - REPLIES TO REQUESTS FOR INTERPRETATION OF EN 14766 |
DIN EN 14872:2006-04 | BICYCLES - ACCESSORIES FOR BICYCLES - LUGGAGE CARRIERS |
PD CEN/TR 16044:2010 | Bicycles. Replies to requests for interpretation of EN 14781 |
S.R. CEN TR 16042:2010 | BICYCLES - REPLIES TO REQUESTS FOR INTERPRETATION OF EN 14765 |
PD CEN/TR 16041:2010 | Bicycles. Replies to requests for interpretation of EN 14764 |
VDI 6224 Blatt 3:2017-09 | Biomimetics - Integrated product development process for biomimetic optimisation |
CEN/TR 16041:2010 | Bicycles - Replies to requests for interpretation of EN 14764 |
PD CEN/TR 16043:2010 | Bicycles. Replies to requests for interpretation of EN 14766 |
I.S. EN 15918:2011 | CYCLES - CYCLE TRAILERS - SAFETY REQUIREMENTS AND TEST METHODS |
CEN/TR 16042:2010 | Bicycles - Replies to requests for interpretation of EN 14765 |
UNI CEN/TR 16042 : 2010 | BICYCLES - REPLIES TO REQUESTS FOR INTERPRETATION OF EN 14765 |
UNI CEN/TR 16043 : 2010 | BICYCLES - REPLIES TO REQUESTS FOR INTERPRETATION OF EN 14766 |
UNI CEN/TR 16044 : 2010 | BICYCLES - REPLIES TO REQUESTS FOR INTERPRETATION OF EN 14781 |
UNI EN 15918 : 2013 | CYCLES - CYCLE TRAILERS - SAFETY REQUIREMENTS AND TEST METHODS |
CEN/TR 16043:2010 | Bicycles - Replies to requests for interpretation of EN 14766 |
UNE-EN 15918:2012 | Cycles - Cycle trailer - Safety requirements and test methods |
UNI CEN/TR 16041 : 2010 | Bicycles - Replies to requests for interpretation of EN 14764 |
S.R. CEN TR 16044:2010 | BICYCLES - REPLIES TO REQUESTS FOR INTERPRETATION OF EN 14781 |
CEN/TR 16044:2010 | Bicycles - Replies to requests for interpretation of EN 14781 |
BS EN 14872:2006 | Bicycles. Accessories for bicycles. Luggage carriers |
EN 15918:2011+A2:2017 | Cycles - Cycle trailers - Safety requirements and test methods |
EN 14872:2006 | Bicycles - Accessories for bicycles - Luggage carriers |
I.S. EN 14872:2006 | BICYCLES - ACCESSORIES FOR BICYCLES - LUGGAGE CARRIERS |
PD CEN/TR 16042:2010 | Bicycles. Replies to requests for interpretation of EN 14765 |
DIN EN 15918:2013-04 | CYCLES - CYCLE TRAILERS - SAFETY REQUIREMENTS AND TEST METHODS |
ISO 7636:1984 | Bells for bicycles and mopeds Technical specifications |
ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
ISO 9633:2001 | Cycle chains — Characteristics and test methods |
ISO 3452:1984 | Non-destructive testing — Penetrant inspection — General principles |
ISO 5775-1:2014 | Bicycle tyres and rims — Part 1: Tyre designations and dimensions |
ISO 3452-3:2013 | Non-destructive testing — Penetrant testing — Part 3: Reference test blocks |
ISO 5775-2:2015 | Bicycle tyres and rims Part 2: Rims |
ISO 3452-2:2013 | Non-destructive testing Penetrant testing Part 2: Testing of penetrant materials |
ISO 3452-4:1998 | Non-destructive testing Penetrant testing Part 4: Equipment |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.