• Shopping Cart
    There are no items in your cart

EN 15657-1:2009

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Acoustic properties of building elements and of buildings - Laboratory measurement of airborne and structure borne sound from building equipment - Part 1: Simplified cases where the equipment mobilities are much higher than the receiver mobilities, taking whirlpool baths as an example

Superseded date

01-07-2017

Superseded by

EN 15657:2017

Published date

24-06-2009

Sorry this product is not available in your region.

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Principle of the test method
6 Measuring equipment
7 Test facilities
8 Mounting of the specimen
9 Test procedure and evaluation
10 Calculation of single number descriptors
11 Precision
12 Expression of results
13 Test report
Annex A (normative) - List of symbols
Annex B (informative) - Link to EN 12354-5
Annex C (normative) - Calculation of the reference
                      structure borne sound pressure level
Annex D (informative) - Example of an existing test rig
Annex E (informative) - Measurement procedure for the tub
                        filling phase, using a reference
                        water jet
Bibliography

Part 1 of the standard shall apply to any source -receiver configuration where the receiver mobility is 10 dB below the source mobility (see definition of mobility in Clause 3 below). However, part 1 is restricted for the moment to whirlpool baths since only this type of building equipment has been experimentally studied so far; for other types of building equipment, the principle of the method is still valid, but some details in the standard might not be relevant.Therefore, this first part:- specifies methods for the measurement under laboratory conditions of airborne and structure borne sound produced by whirlpool baths connected to low mobility structures; for the case of whirlpool baths, building structures of mass per unit area equal or greater than 220 kg/m2, hollow elements excluded, are considered as low mobility elements;- defines the expression of the results, including data for comparison between products (single value descriptors) and input data for the prediction method (link to standard prEN 12354-5 explained in Annex B).

Committee
CEN/TC 126
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

BS EN 15657:2017 Acoustic properties of building elements and of buildings. Laboratory measurement of structure-borne sound from building service equipment for all installation conditions
DIN EN 15657:2016-02 (Draft) ACOUSTIC PROPERTIES OF BUILDING ELEMENTS AND OF BUILDINGS - LABORATORY MEASUREMENT OF STRUCTURE-BORNE SOUND FROM BUILDING SERVICE EQUIPMENT FOR ALL INSTALLATION CONDITIONS
I.S. EN 15657:2017 ACOUSTIC PROPERTIES OF BUILDING ELEMENTS AND OF BUILDINGS - LABORATORY MEASUREMENT OF STRUCTURE-BORNE SOUND FROM BUILDING SERVICE EQUIPMENT FOR ALL INSTALLATION CONDITIONS
16/30333609 DC : 0 BS EN 15657 - ACOUSTIC PROPERTIES OF BUILDING ELEMENTS AND OF BUILDINGS - LABORATORY MEASUREMENT OF STRUCTURE-BORNE SOUND FROM BUILDING SERVICE EQUIPMENT FOR ALL INSTALLATION CONDITIONS
DIN EN 15657:2017-10 ACOUSTIC PROPERTIES OF BUILDING ELEMENTS AND OF BUILDINGS - LABORATORY MEASUREMENT OF STRUCTURE-BORNE SOUND FROM BUILDING SERVICE EQUIPMENT FOR ALL INSTALLATION CONDITIONS

ISO 3822-1:1999 Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 1: Method of measurement
ISO 10848-1:2017 Acoustics — Laboratory and field measurement of flanking transmission for airborne, impact and building service equipment sound between adjoining rooms — Part 1: Frame document
ISO 16063-21:2003 Methods for the calibration of vibration and shock transducers — Part 21: Vibration calibration by comparison to a reference transducer
ISO 7626-1:2011 Mechanical vibration and shock — Experimental determination of mechanical mobility — Part 1: Basic terms and definitions, and transducer specifications
EN ISO 3741:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Precision methods for reverberation test rooms (ISO 3741:2010)
ISO 140-3:1995 Acoustics — Measurement of sound insulation in buildings and of building elements — Part 3: Laboratory measurements of airborne sound insulation of building elements
ISO 7626-2:2015 Mechanical vibration and shock Experimental determination of mechanical mobility Part 2: Measurements using single-point translation excitation with an attached vibration exciter
ISO 140-1:1997 Acoustics Measurement of sound insulation in buildings and of building elements Part 1: Requirements for laboratory test facilities with suppressed flanking transmission
EN ISO 10848-1:2017 Acoustics - Laboratory and field measurement of flanking transmission for airborne, impact and building service equipment sound between adjoining rooms - Part 1: Frame document (ISO 10848-1:2017)
ISO 5348:1998 Mechanical vibration and shock Mechanical mounting of accelerometers
ISO 3741:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Precision methods for reverberation test rooms
EN 60651:1994/A2:2001 SOUND LEVEL METERS (IEC 60651:1979/A2:2000)
IEC 60651:1979+AMD1:1993+AMD2:2000 CSV Sound level meters

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.