EN 16506:2014
Current
Current
The latest, up-to-date edition.
Systems for renovation of drains and sewers - Lining with a rigidly anchored plastics inner layer (RAPL)
Published date
15-10-2014
Publisher
Sorry this product is not available in your region.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviations
5 Pipes at the 'M' stage
6 Marking
7 Fittings at the 'M' stage
8 Lining system at the 'I' stage
9 Installation
10 Documentation
Annex A (normative) - Test method for anchoring strength of
plastics inner layer by pull-off
Annex B (normative) - 'I' stage crushing strength test
Bibliography
This European Standard specifies performance requirements and describes test methods for pipes and fittings for the renovation of underground drain and sewer systems by lining with a single rigid annulus of structural cementitious grout formed behind a plastics inner layer. This plastics layer serves as permanent formwork anchored to the grout. It is applicable to plastics inner layers and grout systems with or without steel reinforcement.This European Standard does not apply to the structural design of the lining system.NOTESystems with multiple annuli are available, but these are controlled by patent rights and not covered by this European Standard.
| Committee |
CEN/TC 165
|
| DevelopmentNote |
Supersedes PREN 16506. (10/2014)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| NS EN 16506 : 2014 | Identical |
| NF EN 16506 : 2014 | Identical |
| NBN EN 16506 : 2014 | Identical |
| NEN EN 16506 : 2014 | Identical |
| UNE-EN 16506:2015 | Identical |
| DIN EN 16506:2014-12 | Identical |
| PN EN 16506 : 2014 | Identical |
| I.S. EN 16506:2014 | Identical |
| BS EN 16506:2014 | Identical |
| UNI EN 16506 : 2014 | Identical |
| SN EN 16506 : 2014 | Identical |
| I.S. EN ISO 11295:2017 | CLASSIFICATION AND INFORMATION ON DESIGN AND APPLICATIONS OF PLASTICS PIPING SYSTEMS USED FOR RENOVATION AND REPLACEMENT (ISO 11295:2017) |
| EN ISO 11295:2017 | Classification and information on design and applications of plastics piping systems used for renovation and replacement (ISO 11295:2017) |
| BS EN ISO 11295:2017 | Classification and information on design and applications of plastics piping systems used for renovation and replacement |
| ISO 11295:2017 | Classification and information on design and applications of plastics piping systems used for renovation and replacement |
| EN 10048:1996 | Hot rolled narrow steel strip - Tolerances on dimensions and shape |
| EN 15885:2010 | Classification and characteristics of techniques for renovation and repair of drains and sewers |
| EN 728:1997 | Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time |
| EN 1107-2:2001 | Flexible sheets for waterproofing - Determination of dimensional stability - Part 2: Plastic and rubber sheets for roof waterproofing |
| ISO 1133-1:2011 | Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method |
| EN ISO 527-2:2012 | Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012) |
| EN 1542:1999 | Products and systems for the protection and repair of concrete structures - Test methods - Measurement of bond strength by pull-off |
| ISO 2039-1:2001 | Plastics — Determination of hardness — Part 1: Ball indentation method |
| EN 14654-1:2014 | Management and control of operational activities in drain and sewer systems outside buildings - Part 1: Cleaning |
| EN ISO 1133-2:2011 | Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 2: Method for materials sensitive to time-temperature history and/or moisture (ISO 1133-2:2011) |
| EN ISO 11296-7:2013 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 7: Lining with spirally-wound pipes (ISO 11296-7:2011) |
| EN 10025-1:2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions |
| EN ISO 6259-1:2015 | Thermoplastics pipes - Determination of tensile properties - Part 1: General test method (ISO 6259-1:2015) |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| EN 13380:2001 | General requirements for components used for renovation and repair of drain and sewer systems outside buildings |
| CEN/TR 14920:2005 | Jetting resistance of drain and sewer pipes - Moving jet test method |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 11296-1:2009 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 1: General |
| ISO 6259-1:2015 | Thermoplastics pipes Determination of tensile properties Part 1: General test method |
| EN 445:2007 | Grout for prestressing tendons - Test methods |
| EN 196-1:2016 | Methods of testing cement - Part 1: Determination of strength |
| EN ISO 75-2:2013 | Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013) |
| EN 13412:2006 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of modulus of elasticity in compression |
| ISO 4624:2016 | Paints and varnishes — Pull-off test for adhesion |
| ISO 11296-7:2011 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 7: Lining with spirally-wound pipes |
| EN ISO 1133-1:2011 | Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2011) |
| EN 1979:1999 | Plastics piping and ducting systems - Thermoplastics spirally-formed structured-wall pipes - Determination of the tensile strength of a seam |
| EN ISO 2039-1:2003 | Plastics - Determination of hardness - Part 1: Ball indentation method (ISO 2039-1:2001) |
| ISO 1183-1:2012 | Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 11296-4:2009 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 4: Lining with cured-in-place pipes |
| EN 13100-4:2012 | Non destructive testing of welded joints of thermoplastics semifinished products - Part 4: High voltage testing |
| EN 12814-2:2000 | Testing of welded joints of thermoplastics semi-finished products - Part 2: Tensile test |
| EN ISO 4624:2016 | Paints and varnishes - Pull-off test for adhesion (ISO 4624:2016) |
| EN 1610:2015 | Construction and testing of drains and sewers |
| EN 13067:2012 | Plastics welding personnel - Qualification testing of welders - Thermoplastics welded assemblies |
| ISO 1133-2:2011 | Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 2: Method for materials sensitive to time-temperature history and/or moisture |
| ISO 527-3:1995 | Plastics Determination of tensile properties Part 3: Test conditions for films and sheets |
| EN 14117:2004 | Products systems for the protection and repair of concrete structures - Test methods - Determination of time of efflux of cementitious injection products |
| EN 206:2013+A1:2016 | Concrete - Specification, performance, production and conformity |
| EN ISO 1183-1:2012 | Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.