Skip to content
Please enter a keyword to search
  • Preview

    I.S. EN ISO 11295:2017

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    CLASSIFICATION AND INFORMATION ON DESIGN AND APPLICATIONS OF PLASTICS PIPING SYSTEMS USED FOR RENOVATION AND REPLACEMENT (ISO 11295:2017)

    Available format(s):  Hardcopy, PDF

    Superseded date:  10-03-2022

    Language(s):  English

    Published date:  01-01-2017

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National Foreword
    European foreword
    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Abbreviated terms
    5 Classification of renovation and replacement techniques
    6 Classification of renovation techniques
    7 Classification of trenchless replacement techniques
    8 Information on design
    9 Aspects affecting installation
    Bibliography

    Abstract - (Show below) - (Hide below)

    Defines families of techniques for the renovation and trenchless replacement (on or off the line of an existing pipeline) of non-pressure and pressure pipelines through the use of plastics pipes, including plastics composites formed in situ into pipes, fittings and ancillary components.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes I.S. EN 13689. (03/2010)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 25780:2011 Plastics piping systems for pressure and non-pressure water supply, irrigation, drainage or sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin — Pipes with flexible joints intended to be installed using jacking techniques
    EN 14636-1:2009 Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 1: Pipes and fittings with flexible joints
    ISO 10467:2004 Plastics piping systems for pressure and non-pressure drainage and sewerage Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
    ISO 11296-1:2009 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 1: General
    ISO 10639:2017 Plastics piping systems for pressure and non-pressure water supply Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
    ISO 11296-3:2009 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 3: Lining with close-fit pipes
    ISO 11299-1:2011 Plastics piping systems for renovation of underground gas supply networks Part 1: General
    ISO 11296-7:2011 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 7: Lining with spirally-wound pipes
    ISO 24511:2007 Activities relating to drinking water and wastewater services — Guidelines for the management of wastewater utilities and for the assessment of wastewater services
    EN 12889:2000 Trenchless construction and testing of drains and sewers
    ISO 18672-1:2009 Plastics piping systems for non-pressure drainage and sewerage — Polyester resin concrete (PRC) — Part 1: Pipes and fittings with flexible joints
    ISO 24512:2007 Activities relating to drinking water and wastewater services — Guidelines for the management of drinking water utilities and for the assessment of drinking water services
    ISO 11299-3:2011 Plastics piping systems for renovation of underground gas supply networks Part 3: Lining with close-fit pipes
    ISO 11298-3:2010 Plastics piping systems for renovation of underground water supply networks Part 3: Lining with close-fit pipes
    ISO 11296-4:2009 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 4: Lining with cured-in-place pipes
    ISO 11298-1:2010 Plastics piping systems for renovation of underground water supply networks Part 1: General
    ISO 16611:2017 Plastics piping systems for drainage and sewerage without pressure — Non-circular pipes and joints made of glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resins (UP) — Dimensions, requirements and tests
    ISO 24510:2007 Activities relating to drinking water and wastewater services — Guidelines for the assessment and for the improvement of the service to users
    ISO 11297-1:2013 Plastics piping systems for renovation of underground drainage and sewerage networks under pressure Part 1: General
    ISO 1043-1:2011 Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
    EN 16506:2014 Systems for renovation of drains and sewers - Lining with a rigidly anchored plastics inner layer (RAPL)
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective