EN 50216-10:2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Power transformer and reactor fittings - Part 10: Oil-to-air heat exchangers
28-01-2022
06-03-2009
1 Scope
2 Normative references
3 Definitions
4 Requirements
4.1 Rated values
4.2 Rated cooling capacity
4.3 Mechanical design
4.4 Protection of surfaces
5 Designation
5.1 Designation of the heat exchangers
5.2 Rating plate information
6 Tests
6.1 Routine tests
6.2 Type tests
7 Preparation for transport and storage
8 Mounting and service, service conditions
Annex A (normative) - Design details of heat exchangers
Annex B (normative) - Performance of heat exchangers
Bibliography
EN 50216-10 describes oil-to-air heat exchangers that means a heat exchanger for the cooling of the transformer oil using a forced oil circuit and a forced air circuit. The oil-to-air heat exchangers are not included in the scope of the Pressure Equipment Directive 97/23/EC according to Article 1, § 3.12. This standard establishes essential dimensions and the requirements to ensure interchangeability and adequate mounting of the oil-to-air heat exchangers. This standard applies for dimensions and requirements of oil-to-air heat exchangers. The increase of ratings and constructional changes as well are considered in the revised standard.
| Committee |
CLC/TC 14
|
| DevelopmentNote |
To be read in conjunction with EN 50216-1. (03/2009)
|
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| UNE-EN 50216-10:2010 | Identical |
| SN EN 50216-10 : 2009 | Identical |
| NEN EN 50216-10 : 2009 | Identical |
| NF EN 50216-10 : 2009 | Identical |
| NBN EN 50216-10 : 2009 | Identical |
| DIN EN 50216-10 : 2009 | Identical |
| PN EN 50216-10 : 2009 | Identical |
| I.S. EN 50216-10:2009 | Identical |
| BS EN 50216-10:2009 | Identical |
| VDE 0532-216-10 : 2009 | Identical |
| CEI EN 50216-10 : 2010 | Identical |
| I.S. EN 50216-12:2011 | POWER TRANSFORMER AND REACTOR FITTINGS - PART 12: FANS |
| UNE-EN 50216-12:2011 | Power transformer and reactor fittings - Part 12: Fans |
| EN 50216-12:2011 | Power transformer and reactor fittings - Part 12: Fans |
| BS EN 50216-12:2011 | Power transformer and reactor fittings Fans |
| ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs |
| EN 10027-2:2015 | Designation systems for steels - Part 2: Numerical system |
| EN ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:2009) |
| EN ISO 1461:2009 | Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods (ISO 1461:2009) |
| EN 10025:1990/A1:1993 | HOT ROLLED PRODUCTS OF NON-ALLOY STRUCTURAL STEELS - TECHNICAL DELIVERY CONDITIONS |
| ISO 1461:2009 | Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods |
| EN 10088-2:2014 | Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes |
| IEC 60296:2012 RLV | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| EN 60296:2012 | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| EN 10130:2006 | Cold rolled low carbon steel flat products for cold forming - Technical delivery conditions |
| EN 754-2:2016 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 2: Mechanical properties |
| EN 1386:2007 | Aluminium and aluminium alloys - Tread plate - Specifications |
| EN 60721-3-4:1995/A1:1997 | CLASSIFICATION OF ENVIRONMENTAL CONDITIONS - PART 3: CLASSIFICATION OF GROUPS OF ENVIRONMENTAL PARAMETERS AND THEIR SEVERITIES - SECTION 4: STATIONARY USE AT NON-WEATHER-PROTECTED LOCATIONS |
| EN 12451:2012 | Copper and copper alloys - Seamless, round tubes for heat exchangers |
| 1997/23/EC : 1997 | DIRECTIVE 97/23/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 MAY 1997 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING PRESSURE EQUIPMENT |
| EN 50216-1:2002 | Power transformer and reactor fittings - Part 1: General |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.