• EN 60068-2-13 : 1999

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    ENVIRONMENTAL TESTING - PART 2: TESTS - TEST M: LOW AIR PRESSURE

    Available format(s): 

    Superseded date:  26-04-2021

    Language(s): 

    Published date:  13-01-2013

    Publisher:  European Committee for Standards - Electrical

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    PREFACE
    Clause
    1. Introduction
    2. General description
    3. Description of test apparatus
    4. Severities
    5. Pre-conditioning
    6. Initial measurements
    7. Conditioning
    8. Recovery
    9. Final measurements
    10. Information to be given in the relevant
        specification
    Annex ZA (normative) Normative references to international
                         publications with their corresponding
                         European publications

    Abstract - (Show below) - (Hide below)

    Covers low pressure tests at room temperature. The aim of the test is to determine the ability of components, equipment or other articles to be stored, transported or used under low air pressure conditions.

    General Product Information - (Show below) - (Hide below)

    Committee SR 104
    Development Note Supersedes HD 323.2.13. (03/2004)
    Document Type Standard
    Publisher European Committee for Standards - Electrical
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS EN 61337-1:2004 Filters using waveguide type dielectric resonators Generic specification
    BS EN 60689:2009 Measurement and test methods for tuning fork quartz crystal units in the range from 10 kHz to 200 kHz and standard values
    CEI EN 62341-5 : 2011 ORGANIC LIGHT EMITTING DIODE (OLED) DISPLAYS - PART 5: ENVIRONMENTAL TESTING METHODS
    BS EN 62575-1:2016 Radio frequency (RF) bulk acoustic wave (BAW) filters of assessed quality Generic specification
    14/30311384 DC : 0 BS EN 60115-2:2014+A1 - FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT - PART 2: SECTIONAL SPECIFICATION: LEADED FIXED LOW POWER FILM RESISTORS
    BS EN 61757-1:2012 (published 2012-08) Fibre optic sensors Generic specification
    BS EN 62040-5-3:2017 Uninterruptible power systems (UPS) DC output UPS. Performance and test requirements
    BS EN 60862-1:2015 Surface acoustic wave (SAW) filters of assessed quality Generic specification
    CEI EN 60512-11-11 : 2003 CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 11-11: CLIMATIC TESTS - TEST 11K: LOW AIR PRESSURE
    BS EN 60384-1 : 2016 FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT - PART 1: GENERIC SPECIFICATION
    BS EN 60938-1 : 2000 FIXED INDUCTORS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION - PART 1: GENERIC SPECIFICATION
    BS EN 140101:2008 Blank Detail Specification. Fixed low power film resistors
    BS EN 61169-8 : 2007 RADIO-FREQUENCY CONNECTORS - PART 8: SECTIONAL SPECIFICATION - RF COAXIAL CONNECTORS WITH INNER DIAMETER OF OUTER CONDUCTOR 6,5 MM (0,256 IN) WITH BAYONET LOCK - CHARACTERISTICS IMPEDANCE 50 OHMS (TYPE BNC)
    I.S. EN 61051-1:2008 VARISTORS FOR USE IN ELECTRONIC EQUIPMENT - PART 1: GENERIC SPECIFICATION
    I.S. EN 61757-1:2012 FIBRE OPTIC SENSORS - PART 1: GENERIC SPECIFICATION (IEC 61757-1:2012 (EQV))
    I.S. EN 61810-7:2006 ELECTROMECHANICAL ELEMENTARY RELAYS - PART 7: TEST AND MEASUREMENT PROCEDURES
    I.S. EN 140402-801:2015 DETAIL SPECIFICATION: FIXED LOW POWER WIREWOUND SURFACE MOUNT (SMD) RESISTORS - RECTANGULAR - STABILITY CLASSES 0,5; 1; 2
    I.S. EN 62575-1:2016 RADIO FREQUENCY (RF) BULK ACOUSTIC WAVE (BAW) FILTERS OF ASSESSED QUALITY - PART 1: GENERIC SPECIFICATION
    I.S. EN 62341-5:2009 ORGANIC LIGHT EMITTING DIODE (OLED) DISPLAYS - PART 5: ENVIRONMENTAL TESTING METHODS
    I.S. EN 60939-1:2010 PASSIVE FILTER UNITS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION - PART 1: GENERIC SPECIFICATION
    EN 60512-9-3:2011 CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 9-3: ENDURANCE TESTS - TEST 9C: MECHANICAL OPERATION (ENGAGING/SEPARATING) WITH ELECTRICAL LOAD
    EN 61337-1:2004 FILTERS USING WAVEGUIDE TYPE DIELECTRIC RESONATORS - PART 1: GENERIC SPECIFICATION
    EN 61019-1 : 2005 Surface acoustic wave (SAW) resonators - Part 1: Generic specification
    EN 62246-1:2015 REED SWITCHES - PART 1: GENERIC SPECIFICATION (IEC 62246-1:2015)
    EN 140402-801:2015 DETAIL SPECIFICATION: FIXED LOW POWER WIREWOUND SURFACE MOUNT (SMD) RESISTORS - RECTANGULAR - STABILITY CLASSES 0,5; 1; 2
    EN 60939-1:2010 PASSIVE FILTER UNITS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION - PART 1: GENERIC SPECIFICATION
    EN 140101:2008 Blank Detail Specification: Fixed low power film resistors
    EN 62341-5 : 2009 ORGANIC LIGHT EMITTING DIODE (OLED) DISPLAYS - PART 5: ENVIRONMENTAL TESTING METHODS
    EN 62040-5-3 : 2017 UNINTERRUPTIBLE POWER SYSTEMS (UPS) - PART 5-3: DC OUTPUT UPS - PERFORMANCE AND TEST REQUIREMENTS (IEC 62040-5-3:2016)
    EN 61051-1 : 2008 VARISTORS FOR USE IN ELECTRONIC EQUIPMENT - PART 1: GENERIC SPECIFICATION
    EN 60738-1:2006/A1:2009 THERMISTORS - DIRECTLY HEATED POSITIVE TEMPERATURE COEFFICIENT - PART 1: GENERIC SPECIFICATION
    EN 62604-1:2015 Surface acoustic wave (SAW) and bulk acoustic wave (BAW) duplexers of assessed quality - Part 1: Generic specification
    EN 60115-2 : 2015 FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT - PART 2: SECTIONAL SPECIFICATION: LEADED FIXED LOW POWER FILM RESISTORS (IEC 60115-2:2014, MODIFIED)
    EN 60068-2-40 : 1999 Environmental testing - Part 2: Tests - Test Z/AM: Combined cold/low air pressure tests
    EN 140401:2009 BLANK DETAIL SPECIFICATION: FIXED LOW POWER FILM SURFACE MOUNT (SMD) RESISTORS
    EN 60068-2-41 : 1999 ENVIRONMENTAL TESTING - PART 2-41 - TESTS - TEST Z/BM - COMBINED DRY HEAT/LOW AIR PRESSURE TESTS
    EN 140402:2015/A1:2016 BLANK DETAIL SPECIFICATION: FIXED LOW POWER WIREWOUND SURFACE MOUNT (SMD) RESISTORS
    BS EN 60738-1 : 2006 THERMISTORS - DIRECTLY HEATED POSITIVE TEMPERATURE COEFFICIENT - PART 1: GENERIC SPECIFICATION
    BS EN 62341-5:2009 (published 2010-02) Organic light emitting diode (OLED) displays Environmental testing methods
    BS EN 61051-1 : 2008 VARISTORS FOR USE IN ELECTRONIC EQUIPMENT - PART 1: GENERIC SPECIFICATION
    I.S. EN 61337-2:2004 FILTERS USING WAVEGUIDE TYPE DIELECTRIC RESONATORS - PART 2: GUIDANCE FOR USE
    BS EN 61338-1:2005 Waveguide type dielectric resonators Generic specification
    BS EN 60115-8-1 : 2015 FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT - PART 8-1: BLANK DETAIL SPECIFICATION: FIXED SURFACE MOUNT (SMD) LOW POWER FILM RESISTORS FOR GENERAL ELECTRONIC EQUIPMENT, CLASSIFICATION LEVEL G
    BS EN 62884-1:2017 Measurement techniques of piezoelectric, dielectric and electrostatic oscillators Basic methods for the measurement
    BS EN 61988-4 : 2007 PLASMA DISPLAY PANELS - PART 4: CLIMATIC AND MECHANICAL TESTING METHODS
    I.S. EN 61337-1:2005 FILTERS USING WAVEGUIDE TYPE DIELECTRIC RESONATORS - PART 1: GENERIC SPECIFICATION
    CEI EN 60393-1 : 2010 POTENTIOMETERS FOR USE IN ELECTRONIC EQUIPMENT - PART 1: GENERIC SPECIFICATION
    CEI EN 62884-1 : 1ED 2018 MEASUREMENT TECHNIQUES OF PIEZOELECTRIC, DIELECTRIC AND ELECTROSTATIC OSCILLATORS - PART 1: BASIC METHODS FOR THE MEASUREMENT
    I.S. EN 140402:2015 BLANK DETAIL SPECIFICATION: FIXED LOW POWER WIREWOUND SURFACE MOUNT (SMD) RESISTORS
    BS EN 60115-1 : 2011 FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT - PART 1: GENERIC SPECIFICATION
    I.S. EN 60115-8-1:2015 FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT - PART 8-1: BLANK DETAIL SPECIFICATION: FIXED SURFACE MOUNT (SMD) LOW POWER FILM RESISTORS FOR GENERAL ELECTRONIC EQUIPMENT, CLASSIFICATION LEVEL G
    EN 62884-1 : 2017 MEASUREMENT TECHNIQUES OF PIEZOELECTRIC, DIELECTRIC AND ELECTROSTATIC OSCILLATORS - PART 1: BASIC METHODS FOR THE MEASUREMENT (IEC 62884-1:2017)
    I.S. EN 60115-8:2012 FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT - PART 8: SECTIONAL SPECIFICATION - FIXED SURFACE MOUNT RESISTORS (IEC 60115-8:2009 (MOD))
    I.S. EN 60384-1:2016 FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT - PART 1: GENERIC SPECIFICATION
    I.S. EN 140401:2009 BLANK DETAIL SPECIFICATION: FIXED LOW POWER FILM SURFACE MOUNT (SMD) RESISTORS
    CEI EN 60512-9-3 : 2012 CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 9-3: ENDURANCE TESTS - TEST 9C: MECHANICAL OPERATION (ENGAGING/SEPARATING) WITH ELECTRICAL LOAD
    I.S. EN 60368-1:2000 PIEZOELECTRIC FILTERS OF ASSESSED QUALITY - PART 1: GENERIC SPECIFICATION
    I.S. EN 60393-1:2009 POTENTIOMETERS FOR USE IN ELECTRONIC EQUIPMENT - PART 1: GENERIC SPECIFICATION
    I.S. EN 140100:2008 SECTIONAL SPECIFICATION: FIXED LOW POWER FILM RESISTORS
    I.S. EN 60512-9-3:2011 CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 9-3: ENDURANCE TESTS - TEST 9C: MECHANICAL OPERATION (ENGAGING/SEPARATING) WITH ELECTRICAL LOAD
    I.S. EN 60512-11-11:2002 CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 11-11: CLIMATIC TESTS - TEST 11K: LOW AIR PRESSURE
    BS EN 60115-2:2015 Fixed resistors for use in electronic equipment Sectional specification: Leaded fixed low power film resistors
    CEI EN 60115-8-1 : 2016 FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT - PART 8-1: BLANK DETAIL SPECIFICATION: FIXED SURFACE MOUNT (SMD) LOW POWER FILM RESISTORS FOR GENERAL ELECTRONIC EQUIPMENT, CLASSIFICATION LEVEL G
    BS EN 60393-1 : 2009 POTENTIOMETERS FOR USE IN ELECTRONIC EQUIPMENT - PART 1: GENERIC SPECIFICATION
    BS EN 60939-1 : 2010 PASSIVE FILTER UNITS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION - PART 1: GENERIC SPECIFICATION
    BS EN 60068-2-41 : 2000 ENVIRONMENTAL TESTING - TEST METHODS - TESTS - TEST Z/BM: COMBINED DRY HEAT/LOW AIR PRESSURE TESTS
    BS EN 61019-1:2005 Surface acoustic wave (SAW) resonators Generic specification
    BS EN 140401-801 : 2007 DETAIL SPECIFICATION: FIXED LOW POWER FILM SMD RESISTORS - RECTANGULAR - STABILITY CLASSES 0,1; 0,25; 0,5; 1
    BS EN 140401-803 : 2007 DETAIL SPECIFICATION: FIXED LOW POWER FILM SMD RESISTORS - CYLINDRICAL - STABILITY CLASSES 0,05; 0,1; 0,25; 0,5; 1; 2
    BS EN 61169-1 : 2013 RADIO-FREQUENCY CONNECTORS - PART 1: GENERIC SPECIFICATION - GENERAL REQUIREMENTS AND MEASURING METHODS
    CEI EN 60368-1 : 2006 PIEZOELECTRIC FILTERS OF ASSESSED QUALITY - PART 1: GENERIC SPECIFICATION
    BS EN 60512-11-11:2002 (published 2002-05) Connectors for electronic equipment. Tests and measurements. Climatic tests Test 11k. Low air pressure
    I.S. EN 60115-2:2015 FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT - PART 2: SECTIONAL SPECIFICATION: LEADED FIXED LOW POWER FILM RESISTORS
    BS EN 60068-2-40 : 2000 ENVIRONMENTAL TESTING - TEST METHODS - TEST Z/AM - COMBINED COLD/LOW AIR PRESSURE TESTS
    06/30155922 DC : 0 BS EN 140100 - SECTIONAL SPECIFICATION - FIXED LOW POWER FILM RESISTORS
    06/30155905 DC : DRAFT SEP 2006 BS EN 140401-803 - DETAIL SPECIFICATION - FIXED LOW POWER FILM SMD RESISTORS - CYLINDRICAL - STABILITY CLASSES 0,05; 0,1; 0,25; 0,5; 1; 2
    14/30317306 DC : 0 BS EN 60115-8-1:2014+A1 - FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT - PART 8-1: BLANK DETAIL SPECIFICATION: FIXED SURFACE MOUNT (SMD) LOW POWER FILM RESISTORS FOR GENERAL ELECTRONIC EQUIPMENT, CLASSIFICATION LEVEL G
    BS EN 60368-1:2000 Piezoelectric filters Generic specification
    BS EN 60512-9-3 : 2011 CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 9-3: ENDURANCE TESTS - TEST 9C: MECHANICAL OPERATION (ENGAGING/SEPARATING) WITH ELECTRICAL LOAD
    OVE/ONORM EN 61051-1 : 2009 VARISTORS FOR USE IN ELECTRONIC EQUIPMENT - PART 1: GENERIC SPECIFICATION
    I.S. EN 62604-1:2015 SURFACE ACOUSTIC WAVE (SAW) AND BULK ACOUSTIC WAVE (BAW) DUPLEXERS OF ASSESSED QUALITY - PART 1: GENERIC SPECIFICATION
    I.S. EN 140401-804:2011 DETAIL SPECIFICATION: FIXED LOW POWER FILM HIGH STABILITY SMD RESISTORS - RECTANGULAR - STABILITY CLASSES 0,1; 0,25
    BS EN 140402 : 2015 BLANK DETAIL SPECIFICATION: FIXED LOW POWER WIREWOUND SURFACE MOUNT (SMD) RESISTORS
    I.S. EN 140101-806:2009 DETAIL SPECIFICATION: FIXED LOW POWER FILM RESISTORS - METAL FILM RESISTORS ON HIGH GRADE CERAMIC, CONFORMAL COATED OR MOLDED, AXIAL OR PREFORMED LEADS
    I.S. EN 60749-2:2002 SEMICONDUCTOR DEVICES - MECHANICAL AND CLIMATIC TEST METHODS - PART 2: LOW AIR PRESSURE
    I.S. EN 61338-1:2005 WAVEGUIDE TYPE DIELECTRIC RESONATORS - PART 1: GENERIC SPECIFICATION
    BS EN 140401-804 : 2011 DETAIL SPECIFICATION: FIXED LOW POWER FILM HIGH STABILITY SMD RESISTORS - RECTANGULAR - STABILITY CLASSES 0,1; 0,25
    BS EN 140401 : 2009 BLANK DETAIL SPECIFICATION: FIXED LOW POWER FILM SURFACE MOUNT (SMD) RESISTORS
    I.S. EN 62884-1:2017 MEASUREMENT TECHNIQUES OF PIEZOELECTRIC, DIELECTRIC AND ELECTROSTATIC OSCILLATORS - PART 1: BASIC METHODS FOR THE MEASUREMENT
    I.S. EN 61019-1:2005 SURFACE ACOUSTIC WAVE (SAW) RESONATORS - PART 1: GENERIC SPECIFICATION
    CEI EN 60068-2-40 : 2000 ENVIRONMENTAL TESTING - PART 2: TESTS - TEST Z/AM: COMBINED COLD/LOW AIR PRESSURE TESTS
    I.S. EN 60938-1:1999 FIXED INDUCTORS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION - PART 1: GENERIC SPECIFICATION
    I.S. EN 60068-2-41:1999 ENVIRONMENTAL TESTING - PART 2: TESTS - TEST Z/BM: COMBINED DRY HEAT/LOW AIR PRESSURE TESTS
    I.S. EN 60115-1:2011 FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT - PART 1: GENERIC SPECIFICATION (IEC 60115-1:2008, MODIFIED)
    EN 140401-804:2011/A1:2013 DETAIL SPECIFICATION: FIXED LOW POWER FILM HIGH STABILITY SMD RESISTORS - RECTANGULAR - STABILITY CLASSES 0,1; 0,25
    BS EN 62604-1:2015 Surface acoustic wave (SAW) and bulk acoustic wave (BAW) duplexers of assessed quality Generic specification
    BS EN 140100 : 2008 SECTIONAL SPECIFICATION: FIXED LOW POWER FILM RESISTORS
    BS EN 60115-8 : 2012 FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT - PART 8: SECTIONAL SPECIFICATION - FIXED SURFACE MOUNT RESISTORS
    10/30237986 DC : 0 BS EN 140401-804 - DETAIL SPECIFICATION: FIXED LOW POWER FILM HIGH STABILITY SMD RESISTORS - RECTANGULAR - STABILITY CLASSES 0,1; 0,25
    08/30186808 DC : DRAFT JULY 2008 BS EN 140401 - BLANK DETAIL SPECIFICATION - FIXED LOW POWER NON-WIRE-WOUND SURFACE MOUNT (SMD) RESISTORS
    BS EN 140401-802 : 2007 DETAIL SPECIFICATION: FIXED LOW POWER FILM SMD RESISTORS - RECTANGULAR - STABILITY CLASSES 1; 2
    CEI EN 61051-1 : 2010 VARISTORS FOR USE IN ELECTRONIC EQUIPMENT - PART 1: GENERIC SPECIFICATION
    BS EN 61337-2:2004 Filters using waveguide type dielectric resonators Guide for use
    BS EN 60122-1 : 2002 QUARTZ CRYSTAL UNITS OF ASSESSED QUALITY - PART 1: GENERIC SPECIFICATION
    BS EN 60749-2 : 2002 SEMICONDUCTOR DEVICES - MECHANICAL AND CLIMATIC TEST METHODS - LOW AIR PRESSURE
    BS EN 61810-7:2006 Electromechanical elementary relays Test and measurement procedures
    I.S. EN 140101:2008 BLANK DETAIL SPECIFICATION: FIXED LOW POWER FILM RESISTORS
    I.S. EN 62246-1:2015 REED SWITCHES - PART 1: GENERIC SPECIFICATION
    EN 140401-802:2007/A3:2017 DETAIL SPECIFICATION: FIXED LOW POWER FILM SMD RESISTORS - RECTANGULAR - STABILITY CLASSES 1; 2
    CEI EN 61810-7 : 2006 ELECTROMECHANICAL ELEMENTARY RELAYS - PART 7: TEST AND MEASUREMENT PROCEDURES
    EN 60384-1:2016 FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT - PART 1: GENERIC SPECIFICATION (IEC 60384-1:2016)
    I.S. EN 60738-1:2006 THERMISTORS - DIRECTLY HEATED POSITIVE TEMPERATURE COEFFICIENT - PART 1: GENERIC SPECIFICATION
    I.S. EN 61020-1:2009 ELECTROMECHANICAL SWITCHES FOR USE IN ELECTRICAL AND ELECTRONIC EQUIPMENT - PART 1: GENERIC SPECIFICATION
    I.S. EN 140401-803:2007 DETAIL SPECIFICATION: FIXED LOW POWER FILM SMD RESISTORS - CYLINDRICAL - STABILITY CLASSES 0,05; 0,1; 0,25; 0,5; 1; 2
    I.S. EN 140401-802:2007 DETAIL SPECIFICATION: FIXED LOW POWER FILM SMD RESISTORS - RECTANGULAR - STABILITY CLASSES 1; 2
    I.S. EN 61169-1:2013 RADIO-FREQUENCY CONNECTORS - PART 1: GENERIC SPECIFICATION - GENERAL REQUIREMENTS AND MEASURING METHODS
    EN 61169-1:2013/AC:2016-02 RADIO-FREQUENCY CONNECTORS - PART 1: GENERIC SPECIFICATION - GENERAL REQUIREMENTS AND MEASURING METHODS (IEC 61169-1:2013)
    EN 60938-1:1999/A1:2007 FIXED INDUCTORS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION - PART 1: GENERIC SPECIFICATION
    EN 60115-1:2011/A11:2015 FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT - PART 1: GENERIC SPECIFICATION
    BS EN 140402-801 : 2015 DETAIL SPECIFICATION: FIXED LOW POWER WIREWOUND SURFACE MOUNT (SMD) RESISTORS - RECTANGULAR - STABILITY CLASSES 0,5; 1; 2
    EN 60862-1:2015 SURFACE ACOUSTIC WAVE (SAW) FILTERS OF ASSESSED QUALITY - PART 1: GENERIC SPECIFICATION (IEC 60862-1:2015)
    CEI EN 61988-4 : 2008 PLASMA DISPLAY PANELS - PART 4: CLIMATIC AND MECHANICAL TESTING METHODS
    CEI EN 60115-2 : 2016 FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT - PART 2: SECTIONAL SPECIFICATION: LEADED FIXED LOW POWER FILM RESISTORS
    CEI EN 140401 : 2009 BLANK DETAIL SPECIFICATION: FIXED LOW POWER FILM SURFACE MOUNT (SMD) RESISTORS
    CEI EN 60115-8 : 2013 FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT - PART 8: SECTIONAL SPECIFICATION - FIXED SURFACE MOUNT RESISTORS
    BS EN 61020-1:2009 (published 2013-05) Electromechanical switches for use in electrical and electronic equipment Generic specification
    BS EN 62246-1:2015 Reed switches Generic specification
    CEI EN 60749-2 : 2004 SEMICONDUCTOR DEVICES - MECHANICAL AND CLIMATIC TEST METHODS - PART 2: LOW AIR PRESSURE
    06/30155911 DC : DRAFT SEP 2006 BS EN 140401-801 - DETAIL SPECIFICATION - FIXED LOW POWER FILM SMD RESISTORS - RECTANGULAR - STABILITY CLASSES 0,1; 0,25; 0,5; 1
    05/30129971 DC : DRAFT FEB 2005 EN 140402-801 - DETAIL SPECIFICATION - FIXED LOW POWER WIRE-WOUND SURFACE MOUNT (SMD) RESISTORS - RECTANGULAR - STABILITY CLASSES 0,5; 1; 2
    BS EN 60068-2-39:2016 ENVIRONMENTAL TESTING - PART 2-39: TESTS - TESTS AND GUIDANCE: COMBINED TEMPERATURE OR TEMPERATURE AND HUMIDITY WITH LOW AIR PRESSURE TESTS
    BS EN 140101-806 : 2008 DETAIL SPECIFICATION: FIXED LOW POWER FILM RESISTORS - METAL FILM RESISTORS ON HIGH GRADE CERAMIC, CONFORMAL COATED OR MOLDED, AXIAL OR PREFORMED LEADS
    I.S. EN 60122-1:2002 AMD 1 2018 QUARTZ CRYSTAL UNITS OF ASSESSED QUALITY - PART 1: GENERIC SPECIFICATION
    CEI EN 60068-2-41 : 2000 ENVIRONMENTAL TESTING - PART 2: TESTS - TEST Z/BM: COMBINED DRY HEAT/LOW AIR PRESSURE TESTS
    I.S. EN 60862-1:2015 SURFACE ACOUSTIC WAVE (SAW) FILTERS OF ASSESSED QUALITY - PART 1: GENERIC SPECIFICATION
    CEI EN 60939-1 : 2011 PASSIVE FILTER UNITS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION - PART 1: GENERIC SPECIFICATION
    I.S. EN 61988-4:2007 PLASMA DISPLAY PANELS - PART 4: CLIMATIC AND MECHANICAL TESTING METHODS
    I.S. EN 140401-801:2007 DETAIL SPECIFICATION: FIXED LOW POWER FILM SMD RESISTORS - RECTANGULAR - STABILITY CLASSES 0,1; 0,25; 0,5; 1
    I.S. EN 60068-2-40:1999 ENVIRONMENTAL TESTING - PART 2: TESTS - TEST Z/AM: COMBINED COLD/LOW AIR PRESSURE TESTS
    EN 140401-803 : 2007 AMD 3 2017 DETAIL SPECIFICATION: FIXED LOW POWER FILM SMD RESISTORS - CYLINDRICAL - STABILITY CLASSES 0,05; 0,1; 0,25; 0,5; 1; 2
    EN 140101-806 : 2008 COR 2014 DETAIL SPECIFICATION: FIXED LOW POWER FILM RESISTORS - METAL FILM RESISTORS ON HIGH GRADE CERAMIC, CONFORMAL COATED OR MOLDED, AXIAL OR PREFORMED LEADS
    EN 140401-801:2007/A1:2013 DETAIL SPECIFICATION: FIXED LOW POWER FILM SMD RESISTORS - RECTANGULAR - STABILITY CLASSES 0,1; 0,25; 0,5; 1
    EN 60749-2:2002 SEMICONDUCTOR DEVICES - MECHANICAL AND CLIMATIC TEST METHODS - PART 2: LOW AIR PRESSURE
    EN 61169-8 : 2007 RADIO-FREQUENCY CONNECTORS - PART 8: SECTIONAL SPECIFICATION - RF COAXIAL CONNECTORS WITH INNER DIAMETER OF OUTER CONDUCTOR 6,5 MM (0,256 IN) WITH BAYONET LOCK - CHARACTERISTICS IMPEDANCE 50 OHMS (TYPE BNC)
    EN 61757-1 : 2012 FIBRE OPTIC SENSORS - PART 1: GENERIC SPECIFICATION (IEC 61757-1:2012)
    EN 60068-2-39:2016 ENVIRONMENTAL TESTING - PART 2-39: TESTS - TESTS AND GUIDANCE: COMBINED TEMPERATURE OR TEMPERATURE AND HUMIDITY WITH LOW AIR PRESSURE TESTS (IEC 60068-2-39:2015)
    EN 60122-1:2002/A1:2018 QUARTZ CRYSTAL UNITS OF ASSESSED QUALITY - PART 1: GENERIC SPECIFICATION (IEC 60122-1:2002/A1:2017)
    EN 60368-1:2000/A1:2004 PIEZOELECTRIC FILTERS OF ASSESSED QUALITY - PART 1: GENERIC SPECIFICATION
    EN 60115-8 : 2012 FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT - PART 8: SECTIONAL SPECIFICATION - FIXED SURFACE MOUNT RESISTORS (IEC 60115-8:2009, MODIFIED)
    EN 61810-7 : 2006 ELECTROMECHANICAL ELEMENTARY RELAYS - PART 7: TEST AND MEASUREMENT PROCEDURES
    EN 62575-1 : 2016 RADIO FREQUENCY (RF) BULK ACOUSTIC WAVE (BAW) FILTERS OF ASSESSED QUALITY - PART 1: GENERIC SPECIFICATION (IEC 62575-1:2015)
    EN 60115-8-1 : 2015 FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT - PART 8-1: BLANK DETAIL SPECIFICATION: FIXED SURFACE MOUNT (SMD) LOW POWER FILM RESISTORS FOR GENERAL ELECTRONIC EQUIPMENT, CLASSIFICATION LEVEL G (IEC 60115-8-1:2014, MODIFIED)
    EN 140100:2008 SECTIONAL SPECIFICATION: FIXED LOW POWER FILM RESISTORS
    EN 61338-1 : 2005 WAVEGUIDE TYPE DIELECTRIC RESONATORS - PART 1: GENERIC SPECIFICATION
    EN 60393-1 : 2009 POTENTIOMETERS FOR USE IN ELECTRONIC EQUIPMENT - PART 1: GENERIC SPECIFICATION
    EN 61337-2 : 2004 FILTERS USING WAVEGUIDE TYPE DIELECTRIC RESONATORS - PART 2: GUIDANCE FOR USE
    EN 60512-11-11 : 2002 CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 11-11: CLIMATIC TESTS - TEST 11K: LOW AIR PRESSURE
    EN 61020-1 : 2009 ELECTROMECHANICAL SWITCHES FOR USE IN ELECTRICAL AND ELECTRONIC EQUIPMENT - PART 1: GENERIC SPECIFICATION
    EN 61988-4 : 2007 PLASMA DISPLAY PANELS - PART 4: CLIMATIC AND MECHANICAL TESTING METHODS

    Standards Referencing This Book - (Show below) - (Hide below)

    HD 323.2.40 : 200S1 BASIC ENVIRONMENTAL TESTING PROCEDURES - TESTS - TEST Z AM: COMBINED COLD LOW AIR PRESSURE TESTS
    ISO 2533:1975 Standard Atmosphere
    HD 323.2.41 : 200S1 BASIC ENVIRONMENTAL TESTING PROCEDURES - TESTS - TEST Z/BM: COMBINED DRY HEAT/LOW AIR PRESSURE TESTS
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective