• There are no items in your cart

EN 60204-11:2000/corrigendum:2010

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 11: REQUIREMENTS FOR HV EQUIPMENT FOR VOLTAGES ABOVE 1000 V A.C. OR 1500 V D.C. AND NOT EXCEEDING 36 KV

Superseded date

10-02-2022

Published date

19-02-2010

INTRODUCTION
1 Scope
2 Normative references
3 Definitions
4 General requirements
5 Incoming supply conductor terminations, devices for
   disconnecting and switching off, and means for earthing
6 Protection against electric shock
7 Protection of HV equipment
8 Equipotential bonding
9 Control circuits and control functions
10 Operator interface and machine-mounted control devices
11 Electronic equipment
12 Controlgear: location, mounting, and enclosures
13 Conductors and cables
14 Wiring practices
15 Electric motors and associated equipment
16 Accessories
17 Marking, warning signs and reference designations
18 Technical documentation
19 Testing and verification
Annex A (informative) - Examples of machines covered by this
        part of IEC 60204
Annex B (informative) - Inquiry form for the HV equipment
         of machines
Annex C (informative) - Method of calculation for the
        cross-sectional area of bare protective conductors
        in supply systems with direct earthing or low
        impedance earthing of the neutral
Annex D (informative) - Relationship between cable rated
        voltages and highest voltage for HV equipment
Annex E (informative) - Rationalization of the use of terms
        relating to earthing and protective bonding
Annex ZA (normative) - Normative references to international
         publications with their corresponding European
         publications
Annex ZZ (informative) - Coverage of Essential Requirements
         of EC Directives
Index

Pertains the electrical and electronic equipment and systems of machines, including a group of machines working together in a coordinated manner, but excluding higher level system aspects (i.e. communications between systems).

Committee
TC 44X
DevelopmentNote
To be used in conjunction with EN 60204-1 (04/2004)
DocumentType
Standard
PublisherName
European Committee for Standards - Electrical
Status
Superseded
SupersededBy

UNE-EN 61400-24:2011 Wind turbines - Part 24: Lightning protection
BS EN 1034-16:2012 Safety of machinery. Safety requirements for the design and construction of paper making and finishing machines Paper and board making machines
BS EN 60703:2009 Test methods for electroheating installations with electron guns
12/30243084 DC : 0 BS EN 1034-21 - SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 21: COATING MACHINES
BS EN 61400-1 : 2005 WIND TURBINES - PART 1: DESIGN REQUIREMENTS
BS EN 60034-1:2010 Rotating electrical machines Rating and performance
DIN EN 1034-16:2012-06 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 16: PAPER AND BOARD MAKING MACHINES
I.S. EN 1012-3:2013 COMPRESSORS AND VACUUM PUMPS - SAFETY REQUIREMENTS - PART 3: PROCESS COMPRESSORS
I.S. EN 15700:2011 SAFETY FOR CONVEYOR BELTS FOR WINTER SPORT OR LEISURE USE
UNE-EN 14985:2012 Cranes - Slewing jib cranes
I.S. EN 1034-17:2012 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 17: TISSUE MAKING MACHINES
DIN EN 1034-3:2012-02 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 3: REREELERS AND WINDERS
BS EN 60519-1:2015 Safety in installations for electroheating and electromagnetic processing General requirements
BS EN 12111:2014 Tunnelling machines. Road headers and continuous miners. Safety requirements
BS EN 618 : 2002
11/30235014 DC : 0 BS EN 13135 - CRANES - SAFETY - DESIGN - REQUIREMENTS FOR EQUIPMENT
I.S. EN 14985:2012 CRANES - SLEWING JIB CRANES
EN 1034-17:2012 Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 17: Tissue making machines
EN 60703:2009 Test methods for electroheating installations with electron guns
EN 16191:2014 Tunnelling machinery - Safety requirements
EN 1034-8:2012 Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 8: Refining plants
EN 12336:2005+A1:2008 Tunnelling machines - Shield machines, thrust boring machines, auger boring machines, lining erection equipment - Safety requirements
EN 60519-1:2015 Safety in installations for electroheating and electromagnetic processing - Part 1: General requirements
DIN EN ISO 12100-1:2004-04 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY
EN 1034-21:2012 Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 21: Coating machines
DIN EN 1034-21:2012-11 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 21: COATING MACHINES
DIN EN 16191 E : 2014 TUNNELLING MACHINERY - SAFETY REQUIREMENTS
03/306578 DC : DRAFT APR 2003 EN 14658 - CONTINUOUS HANDLING EQUIPMENT AND SYSTEMS - SAFETY REQUIREMENTS FOR CONTINUOUS HANDLING EQUIPMENT FOR OPENCAST LIGNITE MINING
UNI EN 16191 : 2014 TUNNELLING MACHINERY - SAFETY REQUIREMENTS
BS EN 61800-4:2003 Adjustable speed electrical power drive systems General requirements. Rating specifications for a.c. power drive systems above 1000 V a.c. and not exceeding 35 kV
UNI EN 15700 : 2012 SAFETY FOR CONVEYOR BELTS FOR WINTER SPORT OR LEISURE USE
BS EN 16191:2014 Tunnelling machinery. Safety requirements
18/30366946 DC : 0 BS EN 17206 - ENTERTAINMENT TECHNOLOGY - LIFTING AND LOAD-BEARING EQUIPMENT FOR STAGES AND OTHER PRODUCTION AREAS WITHIN THE ENTERTAINMENT INDUSTRY - SPECIFICATIONS FOR GENERAL REQUIREMENTS (EXCLUDING ALUMINUM AND STEEL TRUSSES AND TOWERS)
CEI EN 60034-1 : 2015 ROTATING ELECTRICAL MACHINES - PART 1: RATING AND PERFORMANCE
BS EN 13135 : 2013 CRANES - SAFETY - DESIGN - REQUIREMENTS FOR EQUIPMENT
EN 13135:2013+A1:2018 Cranes - Safety - Design - Requirements for equipment
PREN 17206 : DRAFT 2018 ENTERTAINMENT TECHNOLOGY - LIFTING AND LOAD-BEARING EQUIPMENT FOR STAGES AND OTHER PRODUCTION AREAS WITHIN THE ENTERTAINMENT INDUSTRY - SPECIFICATIONS FOR GENERAL REQUIREMENTS (EXCLUDING ALUMINUM AND STEEL TRUSSES AND TOWERS)
I.S. EN 13135:2013 CRANES - SAFETY - DESIGN - REQUIREMENTS FOR EQUIPMENT
I.S. EN 61800-5-1:2007 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY
S.R. CWA 15902-1:2009 LIFTING AND LOAD-BEARING EQUIPMENT FOR STAGES AND OTHER PRODUCTION AREAS WITHIN THE ENTERTAINMENT INDUSTRY - PART 1: GENERAL REQUIREMENTS (EXCLUDING ALUMINIUM AND STEEL TRUSSES AND TOWERS)
DIN EN 1034-22:2010-06 Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 22: Wood grinders (includes Amendment A1:2009)
DIN EN 1012-1:2011-02 Compressors and vacuum pumps - Safety requirements - Part 1: Air compressors
DIN EN 620:2011-07 Continuous handling equipment and systems - Safety and EMC requirements for fixed belt conveyors for bulk materials (includes Amendment A1:2010)
DIN EN 14681:2010-10 Safety of machinery - Safety requirements for machinery and equipment for production of steel by electric arc furnaces (includes Amendment A1:2010)
DIN EN 15011:2014-09 Cranes - Bridge and gantry cranes (includes Amendment A1:2014)
UNE-EN 1034-3:2012 Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 3: Rereelers and winders
BS EN 620 : 2002
I.S. EN 619:2002
I.S. EN 1012-1:2010 COMPRESSORS AND VACUUM PUMPS - SAFETY REQUIREMENTS - PART 1: AIR COMPRESSORS
I.S. EN 1034-22:2005 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 22: WOOD GRINDERS
I.S. EN 14658:2005 CONTINUOUS HANDLING EQUIPMENT AND SYSTEMS - GENERAL SAFETY REQUIREMENTS FOR CONTINUOUS HANDLING EQUIPMENT FOR OPENCAST LIGNITE MINING
I.S. EN 12111:2014 TUNNELLING MACHINES - ROAD HEADERS AND CONTINUOUS MINERS - SAFETY REQUIREMENTS
I.S. EN 14681:2006 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR MACHINERY AND EQUIPMENT FOR PRODUCTION OF STEEL BY ELECTRIC ARC FURNACES
EN 61400-1:2005/A1:2010 WIND TURBINES - PART 1: DESIGN REQUIREMENTS
EN 15011:2011+A1:2014 Cranes - Bridge and gantry cranes
I.S. EN 618:2002
I.S. EN 620:2002
EN 61800-5-1:2007/A1:2017 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY (IEC 61800-5-1:2007/A1:2016)
DIN EN 12336:2010-03 TUNNELLING MACHINES - SHIELD MACHINES, THRUST BORING MACHINES, AUGER BORING MACHINES, LINING ERECTION EQUIPMENT - SAFETY REQUIREMENTS
I.S. EN 1034-3:2011 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 3: REREELERS AND WINDERS
NF EN 619 : 2003 + A1 2010
10/30233949 DC : 0 BS EN 12111 - TUNNELLING MACHINES - ROAD HEADERS, CONTINUOUS MINERS AND IMPACT RIPPERS - SAFETY REQUIREMENTS
15/30296744 DC : 0 BS EN 12013 - PLASTICS AND RUBBER MACHINES - INTERNAL MIXERS - SAFETY REQUIREMENTS
09/30175678 DC : 0 BS EN 14681:2006/A1 - SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR MACHINERY AND EQUIPMENT FOR PRODUCTION OF STEEL BY ELECTRIC ARC FURNACES
11/30243078 DC : 0 BS EN 1034-16 - SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 16: PAPER AND BOARD MAKING MACHINES
BS EN 1034-17:2012 Safety of machinery. Safety requirements for the design and construction of paper making and finishing machines Tissue making machines
BS EN 1034-21:2012 Safety of machinery. Safety requirements for the design and construction of paper making and finishing machines Coating machines
DIN EN 16191:2014-09 TUNNELLING MACHINERY - SAFETY REQUIREMENTS
I.S. EN 1034-16:2012 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 16: PAPER AND BOARD MAKING MACHINES
BS EN 1012-3:2013 Compressors and vacuum pumps. Safety requirements Process compressors
PREN 16191 : DRAFT 2010 TUNNELLING MACHINERY - SAFETY REQUIREMENTS
UNE-EN 60034-1:2011 Rotating electrical machines - Part 1: Rating and performance
UNI EN 1034-8 : 2012 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 8: REFINING PLANTS
I.S. EN 1034-21:2012 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 21: COATING MACHINES
UNI EN 1034-16 : 2012 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 16: PAPER AND BOARD MAKING MACHINES
UNE-EN 13135:2013 Cranes - Safety - Design - Requirements for equipment
DIN EN 1710:2008-08 EQUIPMENT AND COMPONENTS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES
DIN EN 14658:2010-06 Continuous handling equipment and systems - General safety requirements for continuous handling equipment for opencast lignite mining (includes Amendment A1:2010)
BS EN 1034-3:2011 Safety of machinery. Safety requirements for the design and construction of paper making and finishing machines Rereelers and winders
BS EN 61800-5-1:2007 Adjustable speed electrical power drive systems Safety requirements. Electrical, thermal and energy
CEI EN 60519-1 : 2016 SAFETY IN INSTALLATIONS FOR ELECTROHEATING AND ELECTROMAGNETIC PROCESSING - PART 1: GENERAL REQUIREMENTS
EN 618:2002+A1:2010 Continuous handling equipment and systems - Safety and EMC requirements for equipment for mechanical handling of bulk materials except fixed belt conveyors
UNI EN 1012-1 : 2010 COMPRESSORS AND VACUUM PUMPS - SAFETY REQUIREMENTS - PART 1: AIR COMPRESSORS
UNI EN 619 : 2011 CONTINUOUS HANDLING EQUIPMENT AND SYSTEMS - SAFETY AND EMC REQUIREMENTS FOR EQUIPMENT FOR MECHANICAL HANDLING OF UNIT LOADS
UNI EN 1012-3 : 2014 COMPRESSORS AND VACUUM PUMPS - SAFETY REQUIREMENTS - PART 3: PROCESS COMPRESSORS
UNI EN 618 : 2011 CONTINUOUS HANDLING EQUIPMENT AND SYSTEMS - SAFETY AND EMC REQUIREMENTS FOR EQUIPMENT FOR MECHANICAL HANDLING OF BULK MATERIALS EXCEPT FIXED BELT CONVEYORS
UNI EN 1034-6 : 2010 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 6: CALENDER
UNI EN 14985 : 2012 CRANES - SLEWING JIB CRANES
UNI EN 12336 : 2009 TUNNELLING MACHINES - SHIELD MACHINES, THRUST BORING MACHINES, AUGER BORING MACHINES, LINING ERECTION EQUIPMENT - SAFETY REQUIREMENTS
UNI EN 12111 : 2014 TUNNELLING MACHINES - ROAD HEADERS AND CONTINUOUS MINERS - SAFETY REQUIREMENTS
UNI EN 1710 : 2008 EQUIPMENT AND COMPONENTS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES
UNI EN 1034-3 : 2012 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 3: REREELERS AND WINDERS
UNI EN 1034-22 : 2010 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 22: WOOD GRINDERS
UNI EN 14658 : 2010 CONTINUOUS HANDLING EQUIPMENT AND SYSTEMS - GENERAL SAFETY REQUIREMENTS FOR CONTINUOUS HANDLING EQUIPMENT FOR OPENCAST LIGNITE MINING
UNI EN 14681 : 2010 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR MACHINERY AND EQUIPMENT FOR PRODUCTION OF STEEL BY ELECTRIC ARC FURNACES
CEI EN 61400-24 : 2011 WIND TURBINES - PART 24: LIGHTNING PROTECTION
PREN 12013 : DRAFT 2015 PLASTICS AND RUBBER MACHINES - INTERNAL MIXERS - SAFETY REQUIREMENTS
UNI EN 1034-17 : 2012 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 17: TISSUE MAKING MACHINES
11/30227089 DC : 0 BS EN 1034-3 - SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 3: REREELERS AND WINDERS
BS EN 15906:2011 Winter maintenance equipment. Snow removal machines with rotating tools. Specification and clearing capacity
I.S. EN 61400-1:2005 WIND TURBINES - PART 1: DESIGN REQUIREMENTS
DIN EN 15700:2012-01 Safety for conveyor belts for winter sport or leisure use
PREN 1034-3 : DRAFT 2011 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 3: REREELERS AND WINDERS
DIN EN 1034-17:2012-11 Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 17: Tissue making machines
UNE-EN 15700:2012 Safety for conveyor belts for winter sport or leisure use
NF EN 15700 : 2011 SAFETY FOR CONVEYOR BELTS FOR WINTER SPORT OR LEISURE USE
I.S. EN 16191:2014 TUNNELLING MACHINERY - SAFETY REQUIREMENTS
CEI EN 60703 : 2010 TEST METHODS FOR ELECTROHEATING INSTALLATIONS WITH ELECTRON GUNS
DIN EN 13135:2013-05 CRANES - SAFETY - DESIGN - REQUIREMENTS FOR EQUIPMENT
I.S. EN 15011:2011 CRANES - BRIDGE AND GANTRY CRANES
DIN EN 14985:2012-05 Cranes - Slewing jib cranes
EN 620:2002+A1:2010 Continuous handling equipment and systems - Safety and EMC requirements for fixed belt conveyors for bulk materials
DIN EN 618:2011-06 Continuous handling equipment and systems - Safety and EMC requirements for equipment for mechanical handling of bulk materials except fixed belt conveyors
BS EN 619 : 2002
BS EN 12336 : 2005 TUNNELLING MACHINES - SHIELD MACHINES, THRUST BORING MACHINES, AUGER BORING MACHINES, LINING ERECTION EQUIPMENT - SAFETY REQUIREMENTS
BS EN 14985:2012 Cranes. Slewing jib cranes
UNE-EN 619:2003 Continuous handling equipment and systems - Safety and EMC requirements for equipment for mechanical handling of unit loads.
UNE-EN 617:2002 Continuous handling equipment and systems- Safety and EMC requirements for the equipment for the storage of bulk materials in silos, bunkers, bins and hoppers.
BS EN 15011 : 2011 CRANES - BRIDGE AND GANTRY CRANES
BS EN 1710 : 2005 EQUIPMENT AND COMPONENTS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES
10/30218104 DC : 0 BS EN 15011 - CRANES - BRIDGE & GANTRY CRANES
UNE-EN 620:2002 Continuous handling equipment and systems - Safety and EMC requirements for fixed belt conveyors for bulk materials
UNE-EN 618:2002 Continuous handling equipment and systems - Safety and EMC requirements for equipment for mechanical handling of bulk materials except fixed belt conveyors.
EN 619:2002+A1:2010 Continuous handling equipment and systems - Safety and EMC requirements for equipment for mechanical handling of unit loads
EN 14985:2012 Cranes - Slewing jib cranes
EN 15700:2011 Safety for conveyor belts for winter sport or leisure use
EN 14681:2006+A1:2010 Safety of machinery - Safety requirements for machinery and equipment for production of steel by electric arc furnaces
EN 14658:2005+A1:2010 Continuous handling equipment and systems - General safety requirements for continuous handling equipment for opencast lignite mining
EN 15906:2011 Winter maintenance equipment - Snow removal machines with rotating tools - Specification and clearing capacity
BS EN 1034-8:2012 Safety of machinery. Safety requirements for the design and construction of paper making and finishing machines Refining plants
DIN EN 1034-8:2012-06 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 8: REFINING PLANTS
I.S. EN 60703:2009 TEST METHODS FOR ELECTROHEATING INSTALLATIONS WITH ELECTRON GUNS
12/30243081 DC : 0 BS EN 1034-17 - SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 17: TISSUE MAKING MACHINES
10/30233953 DC : 0 BS EN 16191 - TUNNELLING MACHINERY - SAFETY REQUIREMENTS
13/30273033 DC : 0 BS EN 1012-3 - COMPRESSORS AND VACUUM PUMPS - SAFETY REQUIREMENTS - PART 3: PROCESS COMPRESSORS
BS EN 15700:2011 Safety for conveyor belts for winter sport or leisure use
BS EN 60950-23:2006 Information technology equipment. Safety Large data storage equipment
11/30245401 DC : 0 BS EN 1034-8 - SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 8: REFINING PLANTS
I.S. EN 60034-1:2010 ROTATING ELECTRICAL MACHINES - PART 1: RATING AND PERFORMANCE
BS EN 61400-24:2010 Wind turbines Lightning protection
I.S. EN 1034-8:2012 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 8: REFINING PLANTS
I.S. EN 61400-24:2010 WIND TURBINES - PART 24: LIGHTNING PROTECTION
UNI EN 1034-21 : 2012 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 21: COATING MACHINES
CEI EN 61800-4 : 2003 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 4: GENERAL REQUIREMENTS - RATING SPECIFICATIONS FOR A/C/ POWER DRIVE SYSTEMS ABOVE 1000 V A.C. AND NOT EXCEEDING 35 KV
DIN EN 619:2011-02 Continuous handling equipment and systems - Safety and EMC requirements for equipment for mechanical handling of unit loads (includes Amendment A1:2010)
I.S. EN 61800-4:2003 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 4: GENERAL REQUIREMENTS - RATING SPECIFICATIONS FOR A.C. POWER DRIVE SYSTEMS ABOVE 1000 V A.C. AND NOT EXCEEDING 35 KV
I.S. EN 60519-1:2015 SAFETY IN INSTALLATIONS FOR ELECTROHEATING AND ELECTROMAGNETIC PROCESSING - PART 1: GENERAL REQUIREMENTS
BS EN 1012-1:2010 Compressors and vacuum pumps. Safety requirements Air compressors
BS EN 1034-22 : 2005 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 22: WOOD GRINDERS
BS EN 14658 : 2005 CONTINUOUS HANDLING EQUIPMENT AND SYSTEMS - GENERAL SAFETY REQUIREMENTS FOR CONTINUOUS HANDLING EQUIPMENT FOR OPENCAST LIGNITE MINING
BS EN 14681 : 2006 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR MACHINERY AND EQUIPMENT FOR PRODUCTION OF STEEL BY ELECTRIC ARC FURNACES
17/30357380 DC : 0 BS EN 15011 - CRANES - BRIDGE AND GANTRY CRANES
EN 1012-3:2013 Compressors and vacuum pumps - Safety requirements - Part 3: Process compressors
EN 1034-22:2005+A1:2009 Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 22: Wood Grinders
EN 1034-3:2011 Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 3: Rereelers and winders
UNI EN 620 : 2011 CONTINUOUS HANDLING EQUIPMENT AND SYSTEMS - SAFETY AND EMC REQUIREMENTS FOR FIXED BELT CONVEYORS FOR BULK MATERIALS
EN 1034-16:2012 Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 16: Paper and board making machines
EN 61800-4:2003 Adjustable speed electrical power drive systems - Part 4: General requirements - Rating specifications for a.c. power drive systems above 1 000 V a.c. and not exceeding 35 kV
EN 1012-1:2010 Compressors and vacuum pumps - Safety requirements - Part 1: Air compressors
EN 60034-1:2010/corrigendum Oct. 2010 ROTATING ELECTRICAL MACHINES - PART 1: RATING AND PERFORMANCE
EN 61400-24:2010 Wind turbines - Part 24: Lightning protection
EN 12111:2014 Tunnelling machines - Road headers and continuous miners - Safety requirements
UNI EN 15011 : 2014 CRANES - BRIDGE AND GANTRY CRANES
UNE-EN 1034-22:2006 Safety of machinerie - Safety requirements for the design and construction of paper making and finishing machines - Part 22: Wood Grinders
UNE-EN 15011:2011 Cranes - Bridge and gantry cranes
UNE-EN 14658:2006 Continuous handling equipment and systems. General safety requirements for continuous handling equipment for opencast lignite mining
UNE-EN 1034-6:2006 Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 6: Calender

IEC 60364-5-54:2011 Low-voltage electrical installations - Part 5-54: Selection and erection of electrical equipment - Earthing arrangements and protective conductors
EN 60129:1994/A2:1996 ALTERNATING CURRENT DISCONNECTORS AND EARTHING SWITCHES
IEC 60050-195:1998 International Electrotechnical Vocabulary (IEV) - Part 195: Earthing and protection against electric shock
HD 384.4.41 S2:1996/A1:2002 ELECTRICAL INSTALLATIONS OF BUILDINGS - PART 4: PROTECTION FOR SAFETY - CHAPTER 41: PROTECTION AGAINST ELECTRIC SHOCK
EN 60034-1:2010/corrigendum Oct. 2010 ROTATING ELECTRICAL MACHINES - PART 1: RATING AND PERFORMANCE
IEC 60364-4-41:2005+AMD1:2017 CSV Low voltage electrical installations - Part 4-41: Protection for safety - Protection against electric shock
HD 384.2 : 200S2 INTERNATIONAL ELECTROTECHNICAL VOCABULARY - ELECTRICAL INSTALLATIONS OF BUILDINGS
EN 61230:2008 LIVE WORKING - PORTABLE EQUIPMENT FOR EARTHING OR EARTHING AND SHORT-CIRCUITING
IEC 60050-441:1984 International Electrotechnical Vocabulary (IEV) - Part 441: Switchgear, controlgear and fuses
IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
EN 61310-3:2008 Safety of machinery - Indication, marking and actuation - Part 3: Requirements for the location and operation of actuators
IEC 61310-3:2007 Safety of machinery - Indication, marking and actuation - Part 3: Requirements for the location and operation of actuators
IEC 60076-5:2006 Power transformers - Part 5: Ability to withstand short circuit
HD 637 S1:1999/corrigendum:2005 POWER INSTALLATIONS EXCEEDING 1 KV A.C.
IEC 61243-1:2003+AMD1:2009 CSV Live working - Voltage detectors - Part 1: Capacitive type to be used for voltages exceeding 1 kV a.c.
EN 50178:1997 Electronic equipment for use in power installations
IEC 60694:1996+AMD1:2000+AMD2:2001 CSV Common specifications for high-voltage switchgear and controlgear standards
EN 60298:1996/A11:1999 A.C. METAL-ENCLOSED SWITCHGEAR AND CONTROLGEAR FOR RATED VOLTAGES ABOVE 1 KV AND UP TO AND INCLUDING 52 KV
IEC 60865-1:2011 Short-circuit currents - Calculation of effects - Part 1: Definitions and calculation methods
IEC 60129:1984 Alternating current disconnectors and earthing switches
HD 398.5 : S1 AMD 1 POWER TRANSFORMERS - ABILITY TO WITHSTAND SHORT CIRCUIT
HD 384.4.42 : S1 AMD 2 ELECTRICAL INSTALLATIONS OF BUILDINGS - PROTECTION FOR SAFETY - PROTECTION AGAINST THERMAL EFFECTS
EN 60694:1996/A2:2001 COMMON SPECIFICATIONS FOR HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR STANDARDS
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
EN 60865-1:2012 Short-circuit currents - Calculation of effects - Part 1: Definitions and calculation methods
EN 61243-1:2005/A1:2010 LIVE WORKING - VOLTAGE DETECTORS - PART 1: CAPACITIVE TYPE TO BE USED FOR VOLTAGES EXCEEDING 1 KV A.C.
EN 60071-1:2006/A1:2010 INSULATION CO-ORDINATION - PART 1: DEFINITIONS, PRINCIPLES AND RULES
IEC 61230:2008 Live working - Portable equipment for earthing or earthing and short-circuiting
IEC 60034-1:2017 Rotating electrical machines - Part 1: Rating and performance
HD 384.5.54 : 200S1 ELECTRICAL INSTALLATION OF BUILDINGS - SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - EARTHING ARRANGEMENTS AND PROTECTIVE CONDUCTORS
IEC 60071-2:1996 Insulation co-ordination - Part 2: Application guide
EN 60071-2:1997 Insulation co-ordination - Part 2: Application guide
IEC 60050-826:2004 International Electrotechnical Vocabulary (IEV) - Part 826: Electrical installations
ISO 12100-1:2003 Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology
EN 60420:1993 High-voltage alternating current switch-fuse combinations
IEC 61310-1:2007 Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
IEC 60071-1:2006+AMD1:2010 CSV Insulation co-ordination - Part 1: Definitions, principles and rules
ISO 3864:1984 Safety colours and safety signs
IEC 60364-4-42:2010+AMD1:2014 CSV Low-voltage electrical installations - Part 4-42: Protection forsafety - Protection against thermal effects
EN 61310-1:2008 Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals
IEC 60445:2017 Basic and safety principles for man-machine interface, marking and identification - Identification of equipment terminals, conductor terminations and conductors
IEC 60298:1990 A.C. metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV
EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
IEC 60420:1990 High-voltage alternating current switch-fuse combinations

Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.