• Shopping Cart
    There are no items in your cart

EN 60317-25:2010

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Specifications for particular types of winding wires - Part 25: Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200

Superseded date

29-01-2022

Superseded by

EN IEC 60317-25

Published date

07-05-2010

Sorry this product is not available in your region.

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms, definitions and general notes on methods
   of test and appearance
4 Dimensions
5 Electrical resistance
6 Elongation
7 Springiness
8 Flexibility and adherence
9 Heat shock
10 Cut-through
11 Resistance to abrasion (nominal conductor diameters up
   to and including 2,500 mm)
12 Resistance to solvents
13 Breakdown voltage
14 Continuity of insulation
15 Temperature index
16 Resistance to refrigerants
17 Solderability
18 Heat or solvent bonding
19 Dielectric dissipation factor
20 Resistance to transformer oil
21 Loss of mass
23 Pin hole test
30 Packaging
Annex ZA (normative) - Normative references to international
         publications with their corresponding European
         publications

IEC 60317-25:2010 specifies the requirements of enamelled round aluminium winding wires of class 200 with a dual coating. The underlying coating is based on polyester or polyesterimide resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. The superimposed coating is based on polyamide-imide resin. The main changes with respect to the previous edition are: - Clause 3: addition of 3.3: Appearance; - Clause 16: reference to the test for resistance to refrigerants in IEC 60851-4; - Clause 22: deletion of the high temperature failure requirement; - Clause 23: addition of pin hole test requirement.

Committee
CLC/TC 55
DevelopmentNote
Supersedes HD 555.25. (05/2010)
DocumentType
Standard
PublisherName
European Committee for Standards - Electrical
Status
Superseded
SupersededBy
Supersedes

I.S. EN 61858:2008 ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED WIRE-WOUND EIS
BS EN 61858-1:2014 Electrical insulation systems. Thermal evaluation of modifications to an established electrical insulation system (EIS) Wire-wound winding EIS
BS EN 61858:2008 Electrical insulation systems. Thermal evaluation of modifications to an established wire-wound EIS
I.S. EN 60317-0-3:2008 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-3: GENERAL REQUIREMENTS - ENAMELLED ROUND ALUMINIUM WIRE
I.S. EN 61858-1:2014 ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED ELECTRICAL INSULATION SYSTEM (EIS) - PART 1: WIRE-WOUND WINDING EIS
EN 61858-1:2014 Electrical insulation systems - Thermal evaluation of modifications to an established electrical insulation system (EIS) - Part 1: Wire-wound winding EIS
EN 61858:2008 ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED WIRE-WOUND EIS
EN 60317-0-3:2008/A1:2013 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-3: GENERAL REQUIREMENTS - ENAMELLED ROUND ALUMINIUM WIRE (IEC 60317-0-3:2008/A1:2013)

IEC 60317-0-3:2008+AMD1:2013 CSV Specifications for particular types of winding wires - Part 0-3:General requirements - Enamelled round aluminium wire
IEC 60851-5:2008+AMD1:2011 CSV Winding wires - Test methods - Part 5: Electrical properties
EN 60317-0-3:2008/A1:2013 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-3: GENERAL REQUIREMENTS - ENAMELLED ROUND ALUMINIUM WIRE (IEC 60317-0-3:2008/A1:2013)
EN 60851-4:2016 Winding wires - Test methods - Part 4: Chemical properties
EN 60851-5:2008/A1:2011 WINDING WIRES - TEST METHODS - PART 5: ELECTRICAL PROPERTIES (IEC 60851-5:2008)
IEC 60851-4:2016 Winding wires - Test methods - Part 4: Chemical properties

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.